Table of contents
The 3 Major Site Risks
- Financial / Margin: Debonding or cracking of the final floor covering (parquet, tiling) due to excessive residual moisture or thermal shock, resulting in full repair costs in the region of 120 to 280 CHF per square metre, borne entirely by the defaulting parties under art. 368 CO.
- Legal / Joint Body / SUVA: Cross-claims between the screed contractor (CFC 251), the heating contractor (CFC 281) and the floor installer following a failure to comply with the duty of notice under art. 365 para. 3 CO, triggering contractual liability of the appointed parties for lack of technical coordination.
- Administrative / Acceptance: Refusal or deferral of the acceptance of the work under standard SIA 118 due to the absence of a written commissioning protocol or a non-compliant calcium carbide (CM) test record, blocking the release of advance payments and disrupting the overall schedule.
Installing floating screeds over underfloor heating demands rigorous technical coordination between site management, the screed layer covered by CFC 251, the heating installer under CFC 281 and the flooring installer. Under standard SIA 251, pipe embedment and perimeter edge insulation are the primary defences against sound bridging and differential mechanical stresses. Any oversight in monitoring drying times or omitting a thermal temperature stage causes major failures in finishing coverings. Site managers and project supervisors must ensure strict compliance with curing times before any heat is applied, recording every milestone through formal joint inspections on the tracking portal.
Residual moisture testing using the calcium carbide method (CM) is the only approved reference procedure for clearing the installation of sensitive coverings such as parquet or resin coatings. A contractor who identifies a non-compliant substrate or an incomplete heating protocol must notify the client immediately pursuant to art. 365 para. 3 CO, in order to safeguard their rights and avoid liability for subsequent damage. This operational guide details temperature ramp-up curves, representative core sampling points within the screed thickness, and the document traceability required to secure acceptance of the work under standard SIA 118.
Free website tool
Floating Screed Calculator (Cement / Anhydrite), Drying & Commissioning Heat-Up (SIA 251)
SIA 251 regulations and CFC 251 / CFC 281 trade interfaces
The success of a heated floor assembly depends on strict coordination between the heating installer (CFC 281) and the screed layer (CFC 251). Standard SIA 251 sets out the rules of execution for floating screeds, while pipe embedment demands strict adherence to flatness and thickness tolerances. Under standard SIA 251, the nominal screed thickness over heating pipes must meet a precise minimum to ensure heat distribution and prevent punch-through under design service loads. A perimeter insulation strip at least ten millimetres thick must be installed continuously along all vertical elements, columns and door thresholds to eliminate acoustic bridges and allow unrestrained thermal expansion of the floating slab.
The plumbing and heating contractor under CFC 281 must perform a pressure test on the hydronic pipe circuits before the screed is poured. This test pressure must be maintained throughout the screed placing or self-levelling pour to immediately detect any pipe crushing or puncture. The screed contractor checks the compliance of the underlying thermal and acoustic insulation in line with art. 365 CO. If defects are found on the substrate or manifold retaining brackets are missing, the contractor informs the client or their representative in writing.
Occupational safety during aggregate transport and binder pumping requires compliance with art. 3 OPA and art. 82 LAA, ensuring personal protective equipment is worn and pressurised discharge lines are properly anchored. Site management formalises these checks in a joint pour authorisation log.
Methodical functional commissioning heating protocol
Commissioning heating must never begin prematurely to make up lost time on project handovers. For traditional cement screeds governed by standard SIA 251, a minimum wet curing period of twenty-one days is required before any heat input. For calcium sulphate (anhydrite) flowing screeds, the minimum waiting time before heating is typically seven days, in accordance with the binder manufacturer's technical specifications.
The heating protocol comprises two stages: functional commissioning heating to stabilise the binder, followed by drying heating to lower residual moisture:
- Gradual temperature rise: Starting with a flow water temperature of twenty to twenty-five degrees for three full days.
- Thermal increments: Daily increases of five degrees per twenty-four-hour period until reaching the maximum design operating temperature established by the HVAC sizing (typically forty-five to fifty degrees for low-temperature underfloor heating).
- Constant temperature hold: Maintaining this maximum temperature for at least four consecutive days for cement screeds, and until proper drying is achieved for anhydrite screeds.
- Controlled cooling: Stepping down temperatures in five-degree decrements per day until returning to an ambient temperature of approximately twenty degrees.
All temperature readings (flow, return, room ambient) are logged daily on a chart posted at the distribution manifold of each unit. This written traceability provides technical proof of due diligence should micro-cracking or map cracking emerge later.
Carbide method (CM) residual moisture measurement procedure
The calcium carbide method (CM apparatus) remains the only recognised procedure for certifying that a floating screed is ready to receive bonded coverings under standard SIA 251. Electronic dielectric moisture meters provide only qualitative surface readings and carry no contractual weight under Swiss construction law.
The sampling protocol must follow a meticulous operational sequence:
- Circuit locating: Mandatory review of the pipe installation as-built drawings provided by the CFC 281 contractor to avoid striking pipes while chiselling. Measurement points are best pinpointed using screed sensor markers set during pouring.
- Core depth sampling: Taking a sample of around fifty grams for a cement screed (or twenty to twenty-five grams for an anhydrite screed) across the full screed thickness, discarding the top five millimetres of surface exposed to ambient air.
- Crushing and weighing: The sample is finely crushed in a mortar using a steel pestle or hammer, then weighed with a calibrated precision balance.
- Sealed chemical reaction: The screed powder and four steel balls are introduced into the steel testing bottle, followed by the glass ampoule of calcium carbide. After sealing the pressure gauge airtight, vigorous shaking shatters the ampoule. Free water reacts with the carbide to release acetylene, raising internal pressure in proportion to the free water content.
- Stabilised reading: The result in CM percentage is recorded after ten to fifteen minutes of stabilised chemical reaction.
The maximum permissible limit values specified by standard SIA 251 prior to installing parquet or waterproof coverings are 1,5 % CM for cement screeds on underfloor heating, and 0,3 % CM for calcium sulphate screeds on underfloor heating. For bonded or bedded tiles over a cement screed with underfloor heating, the required limit is 1,8 % CM.
Comparative screed table and drying requirements
| Binder type | Waiting time before heating | Max CM rate (tiling) | Max CM rate (parquet) | Moisture sensitivity |
|---|---|---|---|---|
| Traditional cement screed (CFC 251) | 21 days | 1,8 % CM | 1,5 % CM | Low (stable hydraulic binder) |
| Rapid-drying cement screed (with additives) | 7 to 14 days | 1,8 % CM | 1,5 % CM | Low after full hardening |
| Calcium sulphate flowing screed (anhydrite) | 7 days | 0,5 % CM | 0,3 % CM | Very high (loss of strength if rewetted) |
| High-conductivity calcium sulphate screed | 5 days | 0,5 % CM | 0,3 % CM | Very high (requires waterproof protection) |
| Self-levelling pumped cement screed | 14 to 21 days | 1,8 % CM | 1,5 % CM | Low (beware of surface bleed water) |
Common execution errors and financial consequences
Failures observed on Swiss construction sites frequently stem from inadequate coordination between trades. Omitting contraction joints is the leading cause of claims. Under standard SIA 251, any screed bay exceeding forty square metres or running longer than eight metres must incorporate a contraction joint. Door openings must also feature an isolation joint profile to accommodate differential thermal movements between separately controlled heating zones.
Excessively fast heating causes a sharp thermal gradient between the base of the screed and its surface. The binder curls (concave or convex slab-corner curling), ruining floor flatness and shearing skirting joints. Should disputes arise over completed works, client rights regarding rectification or price reductions are governed by art. 368 CO. Under art. 367 CO, the client must promptly inspect the work and notify defects within the statutory sixty-day window for immovable structures.
Remediation costs for curled or cracked screeds beneath bonded parquet range from 140 to 320 CHF per square metre, covering flooring removal, screed grinding, crack stitching with epoxy resin and steel dowel staples, and fully reinstalling the finish flooring. If CFC 281 pipework is damaged during demolition work, contractual liability under art. 97 CO applies fully against the at-fault contractor.
Illustrative practical cases (typical scenarios on Swiss construction sites)
The costs and operational figures provided below serve as illustrative examples to guide site management protocols.
Scenario A: Residential rental building in the Canton of Vaud
On a twelve-apartment residential project in Lausanne, site management oversees the installation of 850 square metres of traditional cement screed on acoustic insulation. The contractor awarded the CFC 251 package deploys a four-person crew. Facing a delayed connection to the district heating substation, the contractor proposes temporary mobile electric boilers to keep the project on track. The heating protocol begins twenty-five days after pouring: three days at twenty degrees, then five-degree increases per day up to forty-five degrees, held for four days. The final CM carbide bomb test performed by the parquet installer indicates 1,3 % CM. The formal joint inspection log is signed, clearing immediate installation of engineered oak without any moisture disputes.
Scenario B: Renovation of an office complex in the canton of Geneva
During the refurbishment of a 420-square-metre administrative floor in Meyrin, a self-levelling anhydrite screed was poured over thin underfloor heating mats. The workforce comprised three workers. Under pressure from site management seeking to avoid contractual delay penalties under art. 160 CO, the heat-up cycle was initiated after only four days, with a direct temperature jump to forty degrees without progressing through incremental steps. Ten days later, the floor installer noted widespread crazing and edge debonding of the screed along the lightweight partitions. CM testing revealed a moisture content still stuck at 1,1 % CM in the lower layer, while the surface crust had detached due to thermal shock. Pursuant to art. 368 CO, the client demanded the full reconstruction of the damaged screed. The cost of complete sanding, pouring a fibre-reinforced self-levelling compound, and the overall delay amounted to around 68 000 CHF, split between site management for lack of supervision and the screed layer for failing to meet their duty of notification under art. 365 CO.
Contracts and SIA 118: free tools
Advance payments and retentions, surety bonds, price escalations, daywork reports, subcontractor monitoring.
Frequently asked questions
Which moisture measurement method is authoritative prior to laying the floor covering under standard SIA 251?
Only the calcium carbide method (CM) measurement is contractually authoritative in Switzerland. Electronic surface tests merely provide non-binding preliminary indications. Taking crushed samples across the full depth of the screed remains required before clearing the work of the floor layer or parquet installer.
What is the permissible residual moisture threshold for laying parquet on a heated cement screed?
The permissible limit is 1,5 % CM for a cement screed with embedded heating (CFC 251 / CFC 281). Exceeding this threshold exposes the floor to wood deformation or severe debonding. The measurement record must be set down in writing prior to any installation.
Does the functional heat-up replace the natural drying of the screed?
No, the functional heat-up is intended to thermally stabilise the mortar and expose potential shrinkage cracks. It in no way waives compliance with the initial curing period, nor does it replace carrying out the final CM measurement before authorising the installation of the floor covering.
What risks does the contractor run if they lay tiles on a screed that is still too damp?
If the contractor installs tiles without prior CM testing, they incur liability for defects in the work under art. 365 CO. In the event of a claim, the full repair costs and substrate rework can represent around 18 000 CHF at their expense.
What is the liability of site management during the recording of the heating protocol?
Site management ensures that daily flow and return temperatures are rigorously logged in accordance with standard SIA 251. It incurs agent liability under art. 398 CO if it authorises covering the floors without requiring the completed, signed heating protocol.
What are the applicable notice of defects deadlines for a defective screed since 2026?
For immovable structures, the client now has 60 days to give notice of defects following their discovery, pursuant to art. 367 CO. The limitation period for claims regarding construction defects is set at five years under art. 371 CO.
Mastering drying kinetics and ensuring the traceability of carbide measurements in accordance with standard SIA 251 are vital safeguards against failures on heated screeds. To consolidate the overall quality of your projects and ensure seamless coordination of finishing work interfaces, consult our specialised technical guides:
- On-Site Technical Quality Control by CFC: Structural Work, MEP and Finishing Work (SIA 414 / 180 / 181)
- Structural Work Inspection (CFC 211): Reinforcement Handover, Concrete Cover (SIA 262) and SIA 414 Tolerances
- Waterproofing Flat Roofs (SIA 271) and Basements (SIA 272): Critical Details and Inspections
- External Joinery and Facades (CFC 221 / 226): Installation in Insulation and Thermal Bridges (SIA 331 / 180)
