Skip to content
Candidates
Jobs
Employers
Companies
Pricing
Change language: French
Practical guide

Employer Day 1 Obligation (CFST 6508 Directive & SUVA): Signed Safety Briefing and Handover of PPE

Employer Day 1 obligations on Swiss sites: PPE issue, safety induction under CFST 6508 directive, and SUVA safety rules.

Table of contents
The 3 Major Site Risks
  1. Financial / Margin: Failing to provide compliant equipment can generate unexpected indirect costs of around 10 000 CHF to 25 000 CHF in an accident attributable to an organisational defect under the Federal Law on Accident Insurance.
  2. Legal / Joint Body / SUVA: Under art. 6 LTr, the employer takes all measures shown by experience to be necessary, applicable according to the state of technology, and suited to the firm's operating conditions; failure to do so exposes the firm to work stoppages by the labour inspectorate.
  3. Administrative / Acceptance: Failing to have the safety induction sheet and the personal protective equipment handover slip signed blocks access to construction sites audited by the site management and the joint committee.

From the moment work begins under art. 319 CO, construction employers in Switzerland must formalise the safety induction of every new recruit. This operational process complies with the requirements of CFST 6508 directive and SUVA safety rules to protect workers' physical integrity against the specific risks of structural work or finishing work.

This guide details the mandatory day-one protocol for general contractors, trade contractors, and HR managers: physical issue of personal protective equipment against written discharge, delivery of vital rules, and documentation onboarding before any work starts on the construction site.

Day 1 operational protocol: formal induction and tracked handover

Carrying out a safety induction when starting a job is not merely good workshop manners, but a direct requirement of the health protection rules under art. 6 LTr. The employer must provide clear instructions suited to the realities of the position and ensure that the worker cooperates fully in following them. To pass SUVA audits and comply with directives from the Federal Coordination Commission for Occupational Safety, each company applies a precise sequence before assigning staff to production tasks.

The process begins with a guided tour of the construction site facilities, identifying plant routes, pinpointing storage zones, and locating first-aid equipment precisely. The instructor then presents the vital rules set for the trade in question. Finally, full personal protective equipment is fitted on the worker, followed by the joint signing of the induction sheet and the handover register.

Day 1 compliance checklist matrix

The table below summarises the mandatory integration checkpoints, their Swiss regulatory basis, and the documentary proof to file in the personnel record.

Control area Operational requirement Official reference Required documentary proof
Health protection Awareness of trade-specific risks and site traffic Labour Act (art. 6 LTr) Dated and signed induction sign-off sheet
Safety organisation Designation of the safety officer and integration into the industry solution CFST 6508 directive Certificate of company safety concept training
Personal equipment Handover of suitable, fully compliant, and fitted PPE Ordinance on Accident Prevention Initialled kit distribution slip with equipment list
Vital rules Explicit briefing on the right to stop dangerous work SUVA safety regulations Initialled commitment form on vital rules
Working hours and rest periods Information on schedules, breaks, and the clocking system Ordinance 1 to the Labour Act (art. 73 OLT 1) Validated working time record sheet

Common induction errors and financial consequences

On Swiss construction sites, rushing to meet delivery deadlines frequently leads to three major errors when a new worker arrives:

  • Handing over PPE without a discharge slip: Providing a helmet, safety boots, and hearing protection without a written signature leaves management unable to prove the equipment was actually issued and checked.
  • Delegating instructions verbally without written backup: Relying on a brief informal briefing by a colleague without recording the topics covered leaves the company vulnerable during cantonal labour inspections.
  • Failing to verify operating competence: Supplying complex fall protection gear without confirming the worker holds a training certificate exposes the team to improper use.

These lapses have major financial repercussions. During an inspection by cantonal authorities or SUVA, finding workers operating without appropriate protection can prompt an immediate work stoppage on the unsecured area. The cost of an entire team sitting idle, combined with contractual delay penalties, commonly adds an unexpected expense of 8 000 CHF to 25 000 CHF per day of shutdown.

Illustrative practical cases (typical scenarios on Swiss construction sites)

The amounts, headcounts, and situations described below are illustrative examples to guide the implementation of company induction protocols.

Scenario A: Arrival of three bricklayers for structural work in the canton of Vaud

A construction general contractor hires three bricklayers to build a residential complex in Lausanne. At 07h00 on their first day, the safety officer gathers the newcomers for a one-hour briefing. He issues their PPE pack, including helmets with chinstraps, safety glasses, hearing protection, cut-resistant gloves, and high-ankle boots. Following a slide presentation on structural work vital rules and a walk through the formwork areas, each worker signs the induction agreement. During an unannounced labour inspection at 11h00, the company immediately produces the signed forms and initialised time records, confirming the site's full compliance.

Scenario B: Hiring an installation electrician in the canton of Geneva

An electrical installation SME hires an installation electrician for a commercial refurbishment construction site in downtown Geneva. Before any work begins in the service shafts, the branch manager reviews the specific risks of live installations and work at height. The tradesperson receives insulating PPE and signs the register confirming they have read the emergency procedures and instructions on stopping work in case of serious danger. The scanned file is immediately saved in the personnel folder, protecting the company against any future disputes regarding compliance with art. 6 LTr obligations.

Wages and social charges: free tools

Real cost of a tradesperson, employer contributions by canton, meal and travel allowances, notice periods under the collective agreement.

View payroll and HR tools

Frequently asked questions

Who pays for personal protective equipment at onboarding?

The employer bears the full cost under the Labour Act. Plan on an indicative budget of around 450 CHF per worker for a baseline pack complying with SUVA guidelines.

Can a worker refuse to use the protective gear provided on the construction site?

No. Under art. 6 LTr, workers are required to support the employer. A deliberate refusal constitutes a breach of contract that justifies a formal warning, or even dismissal with immediate effect for just cause.

How should you handle a worker who speaks none of the national languages?

Safety induction must be delivered using translated visual materials or an appointed language mentor. Signing the induction form confirms mutual understanding of the SUVA vital rules.

What direct financial risk does a company run without a documented safety induction?

In the event of a serious accident, the lack of records exposes the company to retroactive increases in LAA premiums by SUVA, often amounting to tens of thousands of CHF.

How should signed equipment handover slips be kept on record?

Forms must be scanned and kept throughout employment in the worker's personnel folder. This written proof protects the employer during cantonal labour inspectorate audits.

Must safety induction be repeated for a temporary worker?

Yes. The host company remains responsible for workplace induction from day 1. Rigorous application of CFST 6508 directive applies regardless of the contractual arrangement.

Systematically documenting the safety induction and issuing personal protective gear from the very first hour establishes the vital legal basis protecting your firm against disputes. To reinforce your hiring procedures and secure your contractual relationships, consult our expert guides:

Art Construction is an independent company: it is not affiliated with the SIA, CRB, SUVA, or KBOB. Referenced norms and standards point to publications from these bodies; only official versions are legally binding.