Skip to content
Practical guide

IBUS / IUS Bonus for High Energy Performance (Minergie / CECB A) by Romand Canton

Optimise your plans with the Minergie or CECB A IBUS and IUS density bonus in Romandie. SIA 416 standard, calculations, and cantonal permit requirements.

Table of contents
The 3 Major Site Risks
  1. Financial / Margin: Loss of fees and extra cost of revising land-use plans if the density bonus, representing 5% to 10% of floor area, is rejected, resulting in a loss in the region of 40 000 CHF to 80 000 CHF depending on the contract for work.
  2. Legal / Joint Body / SUVA: Refusal or revocation of the building permit by the competent authority pursuant to art. 22 LAT in the event of an unjustified envelope violation not covered by a certified energy exemption.
  3. Administrative / Acceptance: Refusal of the occupancy permit or suspension of CECB A compliance by the municipal authority, requiring additional expert appraisals and a delay in handover of the work according to SIA 118.

Granting a floor area index (IUS) or gross floor area index (IBUS) bonus for high energy performance provides an opportunity for targeted densification in French-speaking Switzerland. Designed for architects, draftspersons, and engineers, this mechanism rewards Minergie or CECB A certifications during the preparation of permit plans.

However, application rules differ depending on cantonal energy laws and municipal building regulations. Rigorous quantification of areas according to the SIA 416 standard prevents envelope errors and secures the compliance of the permit application file with building authority requirements.

Application criteria and transposition of cantonal energy law

Granting an increase in the floor area index (IUS) or gross floor area index (IBUS) relies on project compliance with the heightened requirements of cantonal energy legislation, modelled on the Cantonal Energy Prescriptions Model (MoPEC). To obtain this exemption when the building permit is issued under art. 22 LAT, the designer must demonstrate compliance with a high energy performance standard, such as Minergie, Minergie-P, or Class A of the Cantonal Building Energy Certificate (CECB). This increase in determining floor area does not apply automatically: it requires close coordination with the municipality and compliance with municipal zoning regulations.

In geometrical terms, the permitted increase must not breach alignment rules, boundary setbacks, or maximum ridge or eaves heights, unless an express exemption clause in cantonal law applies. The permit application file must demonstrate the strict demarcation of areas according to the SIA 416 standard in order to separate the baseline regulatory envelope from the supplement granted for energy efficiency.

Romand comparison of density index exemptions for high performance

Calculation rules and allocation thresholds vary significantly from one canton to another, requiring a rigorous reading of local legal foundations when laying out zoning plans.

CantonCantonal legal basisEnergy requirementMaximum increaseSpatial constraints
VaudSpatial Planning and Building ActMinergie or CECB AUp to 5% IBUSMandatory compliance with property boundary setbacks
GenevaBuildings and Diverse Installations ActHigh Energy Performance Standard (HPE)Up to 10% IUSArchitectural integration subject to cantonal preliminary opinion
FribourgSpatial Planning and Building ActMinergie or CECB Class AUp to 10% IBUSPreservation of roof profiles and alignments
ValaisBuilding ActCertified Minergie standard5% index increaseCompatibility with natural hazard zones
NeuchâtelSpatial Planning ActPerformance exceeding the statutory standardBonus of 5% to 10% IBUSClause on integration into the surrounding built fabric

Recurring layout errors and financial repercussions

Failing to clearly isolate the density bonus in the area tables according to the SIA 416 standard is the primary reason building authorities suspend preliminary reviews. A frequent point of confusion is the inclusion of external thermal insulation thickness: in cantons harmonised under the Intercantonal Agreement on the Harmonisation of Building Terminology, excess insulation thickness is already deducted or omitted from the determining area, which prevents combining insulation deductions and the full density bonus without an explicit municipal basis.

Misinterpretation leads to the requirement of submitting a supplementary permit application or modifying an entire floor while the application is under review. Direct financial consequences for the design office routinely run in the region of 25 000 CHF to 60 000 CHF in revised plans, envelope reassessments, and administrative delays, not to mention contractual disputes under the contract for work governed by the Code of Obligations (CO).

Illustrative practical cases (typical scenarios on Swiss construction sites)

The figures and situations presented below are illustrative examples constructed for practical use and do not represent actual construction sites.

Standard scenario: Multi-family building with 14 residential units in a residential zone (Canton of Vaud)

In a multi-family housing project developed by a design team comprising an architect, a civil engineer, and two building draftspersons, the plot has an area of 2 000 m² subject to a baseline municipal IBUS set at 0,60, equating to 1 200 m² of authorised determining floor area. The client wishes to incorporate the Minergie-P label in order to apply for the 5% IBUS increase provided for by the regulations.

The technical approach focused on precise modelling from the preliminary design phase: applying the bonus enables an effective IBUS of 0,63, equating to 1 260 m² of floor area, which generates an additional 60 m² apartment. On the section and elevation drawings, the team formalised an envelope that did not exceed the maximum ridge height permitted by municipal building regulations, absorbing the gained area through interior grid optimisation and a reduction of non-determining circulation areas under the SIA 416 standard. The municipal authority approved the coordinated permit application file without requesting volumetric alterations, avoiding estimated design rework costs in the region of 45 000 CHF.

Surfaces, standards and permits: free tools

SIA 416 floor areas and volumes, cantonal zoning ratios, U-values and dew points, acoustics, planning enquiry requirements.

View engineering tools

Frequently asked questions

How do you justify the IBUS bonus during the public inquiry?

Pursuant to art. 22 LAT, attach the pre-certificate to the municipal file. Plan for a thermal study in the region of 4500 CHF to secure the plans before filing for the inquiry.

Does increased insulation reduce interior usable floor area?

The intercantonal agreement harmonising terminology neutralises external thermal insulation. An investment in the region of 18000 CHF preserves interior usable area without penalising the permitted regulatory building envelopes.

What are the project risks if the label is not obtained?

The municipality may refuse the occupancy permit for non-compliance of the executed works. Bringing the building into compliance requires corrective technical interventions in the region of 35000 CHF.

Does the density bonus authorise exceeding the maximum height?

Municipal zoning regulations permit very narrowly defined envelope adjustments. A structural timber adjustment in the region of 12000 CHF ensures strict geometric compliance of the roof structures.

Can you combine an energy bonus with a housing bonus?

Under the Federal Act on Spatial Planning, combining these bonuses is governed by cantonal law. A preliminary appraisal in the region of 2800 CHF clarifies development rights.

How do you coordinate the thermal assessment with the plans?

The project manager transfers insulation thicknesses onto the execution plans. A geometric check in the region of 5000 CHF prevents any dispute during the municipal inspection.

To learn more about calculating envelopes on your plans, consult our methodological guides:

Art Construction is an independent company: it is not affiliated with the SIA, CRB, SUVA, or KBOB. Referenced norms and standards point to publications from these bodies; only official versions are legally binding.