Skip to content
Sign in Sign up
Categories
Power tools DrillsScrewdriversGrindersSaws Measure Laser levels Protection Protective equipment Site Ladders and stepladdersHand tools
Support
Change language: French
Practical guide

External Thermal Insulation Composite System (ETICS - CFC 226) Fasteners Without Point Thermal Bridging (Chi <= 0,002 W/K)

Technical guide to ETICS anchors without thermal bridging Chi <= 0.002 W/K under CFC 226, standard SIA 118, and revised Swiss CO defect liability rules.

Table of contents
The 3 Major Site Risks
  1. Financial / Margin: Inappropriate anchoring without a thermal bridge break or pulled out under wind suction exposes the contractor to a complete overhaul of the facade build-up. Under art. 368 CO, the client may demand remediation without any admissible restrictive clause, representing an illustrative cost in the region of 180 to 320 CHF per square metre of scaffolding and ETICS build-up to replace.
  2. Legal / Joint committee / SUVA: Drilling and fastening operations on facades require certified safety measures. The absence of facade scaffolding compliant with art. 26 OTConst above a 3 m fall height, or failure to comply with the safety plan prescribed by art. 4 OTConst, exposes site management and the employer to a work stoppage. Intentional endangerment falls under art. 229 CP.
  3. Administrative / Acceptance: The emergence of thermal ghosting or spot condensation leads to defect notifications by the client. Under art. 367 CO, the client has a 60-day deadline to give notice of defects in an immovable work upon inspection, suspending final acceptance under standard SIA 118 and blocking the release of performance bonds.

This technical guide is aimed directly at facade installers, plasterer-painters, civil engineers, and site managers responsible for trade lot CFC 226 (Insulated and ventilated facades, rendered external thermal insulation). Mechanically fastening external thermal insulation requires absolute control over point energy losses. Using anchors with a point thermal bridge coefficient Chi less than or equal to 0,002 W/K prevents visible appearance defects, such as anchor plate ghosting caused by morning moisture, while safeguarding the overall energy performance of the building envelope in the Swiss climate.

Choosing correctly between anchors with a metal core and thermal bridge break, synthetic screw-in plugs with an expanding core, or drive-in hammer anchors depends strictly on the nature of the mineral substrate (concrete, clay brickwork, or calcium silicate masonry) and the required resistance to wind suction loads. Pursuant to art. 365 CO, the contractor is liable for the materials installed and must immediately give notice of any unsuitable or deteriorated substrate prior to mechanical fastening. With the limitation period for defect claims extending over five years under art. 371 CO for an immovable work, anchoring rigour forms the core technical safeguard for the durability of external wall insulation.

Technical and normative selection criteria for ETICS fasteners (CFC 226)

Selecting a rendered external wall insulation anchor in Switzerland meets strict thermal, mechanical, and hygrothermal requirements. The essential requirement of capping the point thermal bridge coefficient Chi at a value less than or equal to 0,002 W/K is designed to eliminate ghosting on the facade render. This phenomenon occurs when the anchor head conducts heat differently from the adjacent insulation, causing variations in the drying of morning condensation that reveal the circular outline of the fixings. The contractor is liable for the good quality of the materials used in accordance with art. 365 CO.

Mechanically, the anchor must absorb wind suction loads acting perpendicular to the wall. These loads vary depending on geographical zone, building height, and roof geometry. The fasteners transfer tensile forces to the load-bearing substrate through the insulation board. Shear forces generated by the self-weight of the insulation and render system are absorbed by the adhesive mortar, reinforced by friction and the flexural rigidity of the anchor shaft.

Planning these operations demands continuous care. Under art. 3 OTConst, work must be planned so that the risk of occupational accidents, occupational illnesses, or harm to health is kept as low as possible. An employer acting as a contractor must examine occupational safety and health protection measures prior to concluding the contract pursuant to art. 3 para. 3 OTConst, with site-specific measures set out in the works contract pursuant to art. 3 para. 5 OTConst.

Anchor Typology and Compatibility with Mineral Substrates

Common anchor substrates across Switzerland fall into various material categories: in situ cast solid concrete, perforated clay brickwork, lightweight concrete blocks, or aerated concrete. The design of the anchor expansion zone must match the density of the mineral substrate with precision:

  • Solid concrete: pure friction expansion anchoring using a glass-fibre-reinforced synthetic expansion nail or a metal screw with an overmoulded plastic head.
  • Hollow masonry and perforated bricks: anchoring through friction and plastic deformation of the sleeve, forming a positive interlock behind the ceramic walls without shattering internal webs.
  • Aerated concrete or porous materials: extended expansion with a dedicated helical thread providing an increased bearing surface without pulverising the mineral matrix.

Installation Methods: Flush Mounting Versus Recessed Counter-Bored Mounting

Two installation methods coexist on Swiss construction sites, dictated by the insulation type (expanded polystyrene EPS, rock or glass mineral wool, rigid polyurethane):

Flush mounting involves tightening or hammering the anchor plate until it sits perfectly flush with the outer face of the insulation. This method requires an anchor fitted with an integrated insulating plug or a solid polyamide overmoulding to guarantee the required Chi value. Setting the anchor too deep creates a depression that collects excess base coat during mesh embedding, locally increasing thermal mass and producing permanent moisture stains.

Recessed mounting (counter-bored or countersunk screw-in) represents the method recommended by best trade practice for high-end facades and thick insulation layers. The anchor plate is recessed 15 to 20 mm below the insulation surface using a dedicated setting tool fitted with a depth stop. An insulation plug cut from the same material as the insulation board closes off the recess. This technique delivers a near-zero Chi value, shielding the work from any uneven surface water absorption.

Comparative matrix of external insulation fixing systems

Fastener categoryThermal and mechanical requirementSwiss construction site usageSite management checkpointConsequence of non-compliance
Drive-in hammer anchor with composite pinChi less than or equal to 0,002 W/K, 60 mm diameter plateStandard EPS boards on shuttered concrete, small multi-family homesMinimum drilling depth, drill hole cleaningAnchor rebound, plate cracking, increased thermal bridging
Screw-in anchor for recessed counter-bored mountingChi less than or equal to 0,001 W/K, EPS or mineral wool plugMinergie buildings, high insulation thicknesses (from 160 mm)Accurate flush alignment of the surface-mounted insulation plugPermanent visual ghosting under raking light
Long-expansion universal anchorGrip in modular perforated bricks and clay masonryRenovations of older facades and mixed masonryDisabling hammer action when drilling into hollow brickShattering of internal webs, zero pull-out resistance
Fastener for offset heavy loadsFull thermal break, fibre-reinforced coneAwnings, railings, hinged shutters on ETICSLoad-bearing chemical anchoring into masonry or concreteLoad sagging, water ingress beneath the render
Supplementary enlarged anchor plate (90-140 mm diameter)Restraint of flexible boards with low tensile strengthRock wool and lamella mineral wool boardsCentred positioning without crushing the rock fibresBoard tear-off under severe wind suction

Common procurement and installation mistakes and their financial impacts

Using an unsuitable drilling method is the leading cause of technical failures. Operating a rotary hammer drill with percussion in clay brick masonry shatters the internal cellular webs. The anchor finds no reliable mechanical anchorage, reducing its pull-out resistance to zero. Drilling in rotary-only mode is imperative to preserve the ceramic structure.

Insufficient drilling depth prevents full expansion of the synthetic anchor sleeve. The contractor must ensure that drilling dust is cleared out and that the free hole depth exceeds the embedment depth of the anchor by at least 10 to 15 mm. If the anchor bottoms out before being fully seated, hammering forces the pin and destroys the plastic sleeve, immediately creating an uneven surface.

Financially, the consequences of non-compliant anchoring are severe. Art. 368 CO governs the client's rights in the event of defects, prohibiting any exclusion clause for immovable structures. If a facade exhibits unevenness or partial delamination, the cost of a complete overhaul—comprising the erection of working scaffolding compliant with art. 26 OTConst, stripping the render and insulation, and reinstalling a full system—ranges typically between 190 and 310 CHF per square metre. For a typical facade area of 650 m², total damages routinely exceed 150 000 CHF.

On the construction site, operative safety remains paramount. During repetitive facade drilling phases from scaffolding, mineral dust concentrations must be controlled. Art. 33 OTConst mandates safeguarding ambient air quality through extraction, filtration, or ventilation, supplemented where necessary by respiratory protective equipment if technical measures do not suffice.

Illustrative practical cases (typical scenarios on Swiss construction sites)

The figures and parameters presented below are illustrative examples intended to guide methodological decisions on Swiss construction sites.

Scenario 1: Residential Rental Building in Canton Vaud

In the Nyon district, a multi-family residential development of 18 housing units undergoes installation of a 200 mm rendered external thermal insulation system using grey expanded polystyrene over 17,5 cm perforated brick masonry. The installation crew comprises 4 facade installers under the supervision of a foreman designated as a competent person under art. 5 OTConst.

Given the high target thermal resistance, a universal screw-in anchor installed using the recessed mounting method is selected. Operatives use twist drill bits operating strictly in rotary-only mode. The dedicated drive tool cuts into the insulation and drives the plate 20 mm beneath the outer face, after which a matching EPS plug is inserted by hand.

This technical choice ensures compliance with the limit value Chi less than or equal to 0,002 W/K, guaranteeing complete freedom from circular ghosting marks once the scraped mineral finish coat is applied. On-site pull-out testing confirms load capacities exceeding the maximum wind suction loads calculated for the Lake Geneva basin plain.

Scenario 2: Energy Retrofit of a School Building in Canton Fribourg

In Bulle, a municipal administrative and school building constructed in 1974 features facades made of exposed aggregate precast concrete panels. The energy retrofit project entails installing 220 mm of non-combustible rigid rock wool boards. The mobilised workforce consists of 5 plasterer-facade installers working from facade scaffolding fitted with compliant perimeter edge protection satisfying art. 22 OTConst and art. 26 OTConst.

The fibrous and dense structure of mineral wool requires increased clamping stiffness. The technical selection settles on steel-pin anchors equipped with a 30 mm long overmoulded insulating polyamide head, combined with 90 mm diameter spreader plates to prevent punch-through into the insulation slab. Pneumatic drilling into the solid concrete is carried out to an embedment depth of 45 mm, followed by meticulous dust removal. The system delivers an adequate thermal bridge break while providing the mechanical strength needed to support the self-weight of the build-up and the wind loads typical of the Pre-Alpine region.

Free construction site calculators

Thirty-five trade calculators: site installations, waste, concrete, screeds, insulation, scaffolding. No sign-up required.

View trade calculators

Frequently asked questions

Which point Chi-value guarantees a thermal break according to CFC 226?

To prevent localised heat loss, the Chi-value must not exceed 0,002 W/K. An anchor with a composite pin or plastic head limits heat transfer through the insulation. This prevents the risk of surface condensation and ensures the building envelope complies with the works contract.

What criminal liability does the site management face if ETICS pulls off?

Under art. 229 CP, anyone who intentionally or through negligence breaches the recognised rules of construction while carrying out or directing work, endangering life or limb, faces a custodial sentence or a monetary penalty. Assessing wind resistance anchorage is therefore essential.

For an immovable work, the client has 60 days to report defects identified after delivery under art. 367 CO. Any shorter contractual deadline is considered null and void. If water ingress occurs due to a poorly installed anchor, the site management must act immediately.

Can the contractor refuse to rectify poorly positioned anchors?

No, art. 368 CO provides that any advance agreement restricting or excluding the right to have defects repaired is void for construction work. If anchors cause damage on the facade, the site management can demand full rectification at no additional cost.

Which collective protection measure applies during facade dowelling work?

Art. 26 OTConst requires facade scaffolding whenever the fall height exceeds 3 m, with a top guard rail extending 80 cm above the working area. Furthermore, under art. 6 OTConst, safety helmets remain mandatory at exposed workstations.

What is the average extra installation cost for a thermal break fastening?

The additional material cost for a thermal break anchor remains modest, around 0,40 CHF to 0,90 CHF per unit. For a typical 300 m² facade, the overall extra cost is in the region of 800 CHF to 1 500 CHF, which quickly pays for itself by preventing building defects.

Carefully selecting fasteners for external thermal insulation composite systems ensures the energy performance and structural stability of the building envelope according to recognised Swiss building practice. Explore our technical guides and engineering tools to complete the dimensioning of your structures:

Art Construction is an independent company: it is not affiliated with the SIA, CRB, SUVA, or KBOB. Referenced norms and standards point to publications from these bodies; only official versions are legally binding.