Table of contents
The 3 Major Site Risks
- Financial / Margin: Purchasing unsuitable equipment leads to operational cost overruns of around 4 500 CHF per workstation over a quarter, caused by premature cartridge clogging and loss of suction on power tools. Under art. 364 CO, the contractor is liable for the resources and equipment deployed. Unplanned manual cleaning time reduces gross margin by 3 % to 7 % on sawing, wall chasing and sanding items.
- Legal / Joint body / SUVA: Failure to comply with recognised occupational safety rules exposes the firm to immediate compliance orders from SUVA inspectors or joint committees. Art. 82 LAA obliges employers to take all preventive measures that are necessary and recognised by state-of-the-art technology. Operating without a certified dust extraction system approved for mineral dust halts surfacing work, with fixed stoppage costs estimated at more than 1 200 CHF per half-day.
- Administrative / Acceptance: The spread of fine quartz particles into adjacent finishing areas jeopardises the acceptance of the work under SIA 118. Art. 366 CO allows the client to set a completion deadline whenever deficient site resources threaten the compliance of the work, with the right to have specialised clearing or cleaning carried out by a third party at the contractor's expense. Delays during joint inspection verifications result in withholdings on advance payments of around 5 % to 10 % of the trade package amount.
Managing solid aerosols and mineral dust is a central technical requirement for conducting construction operations in Switzerland. During concrete cutting, screed surfacing or masonry milling, the concentration of respirable quartz can reach critical levels within minutes in confined or semi-open spaces. The Ordinance on the Safety and Health Protection of Workers in Construction Work specifies these obligations: under art. 33 OTConst, ambient air at workstations must contain between 19 and 21 % oxygen by volume, exposure limit values for hazardous substances must not be exceeded, and these substances must be discharged into the open air, filtered, or diluted through artificial ventilation. Choosing between filter classes L, M or H is therefore not a matter of user preference, but of strict compliance with EN 60335-2-69 and SUVA directives on mineral dust. While class L units are widespread for non-hazardous domestic dust, they do not meet the demands of a structural work or mineral finishing work construction site, where class M is the mandatory minimum technical threshold to protect the respiratory health of crews and the integrity of work areas.
For the site manager, engineer or foreman, setting up an effective extraction system requires coordinated analysis of the entire airflow chain: a suction hood adapted to the power tool, automatic start-stop coupling, continuous pneumatic filter cleaning via sonic or mechanical pulses, and a final filter medium reaching HEPA H14 levels for toxic substances or respirable fibres. The Ordinance on the Prevention of Accidents and Occupational Diseases states, under art. 3 OPA, that employers must take all protective measures and precautions that meet recognised safety engineering rules. By pairing industrial dust extractor selection with mobile air scrubbers creating controlled negative pressure in occupied or renovated areas, the contractor prevents fine dust migration toward service ducts and previously accepted surfaces. This technical guide outlines maximum permeability thresholds under EN 60335-2-69, compares dust-free disposal protocols using sealed safety bags, and provides the methodological keys to dimension your source extraction points in compliance with federal requirements and safety regulations in force across Switzerland.
Swiss regulatory framework: duty of stakeholders and SUVA prevention doctrine
Deploying industrial dust extraction and air filtration systems in Switzerland rests on a set of legal obligations shared among employers, workers and occupational safety inspection bodies. The Ordinance on the Safety and Health Protection of Workers in Construction Work mandates rigorous site planning to guarantee respirable ambient air at all times and prevent the dispersion of hazardous solid aerosols. This requirement applies right from the tender preparation phase through to site decommissioning. The employer is responsible for providing equipment tailored to the physical and chemical risks identified on site, taking into account the friability and toxicity characteristics of the materials processed.
Under art. 364 CO, the contractor procures at its own expense the means, machinery and tools required to execute the work, encompassing all extraction and air treatment systems needed to deliver work in accordance with trade best practice. Consequently, structural work, finishing work or demolition firms cannot evade the duty to provide compliant extractors and air scrubbers by citing the absence of explicit specifications in the call for tenders quote descriptions. Recognised rules of technology form an integral part of the contractual and statutory duties owed by contractors to the site management.
Responsibilities of employers and workers on Swiss construction sites
The employer must verify the operating condition and compliance of dust capture devices before each deployment on site. Industrial extractors equipped with airflow monitoring systems and undamaged filters, matched to the hazard class of the dust generated, must be placed at the disposal of work crews. The employer also organises specific operator training covering receiver bag changes, filter element cleaning, and routine servicing without resuspending dust into the rooms. The employer appoints the qualified safety officer tasked with daily monitoring of air treatment protocols.
For their part, workers must systematically use the collective and personal protective equipment provided, without altering its operation or bypassing safety devices. Any observed abnormal drop in negative pressure, hose blockage or cartridge clogging requires mechanical machining tasks to be stopped immediately until nominal extraction parameters are restored. Ordinance 3 to the Labour Act, in its provisions on health protection, reiterates the principles of prevention against physical and chemical nuisances in the workplace, highlighting the importance of preventive maintenance for dust extraction systems.
SUVA inspections and enforcement by cantonal joint committees
The Swiss National Accident Insurance Fund (SUVA) carries out targeted inspections on construction sites across French-speaking Switzerland and throughout the Confederation to verify compliance with occupational exposure limit values (OELVs). During unannounced site visits, SUVA inspectors prioritise checking the direct connection of power tools to a certified dust extractor, the integrity of suction hoses, the filtration class displayed on the equipment rating plate, and the presence of acoustic or visual warning devices triggered by airflow drops.
In the event of a serious violation, such as dry grinding a concrete slab with a non-compliant domestic vacuum cleaner or without effective dust extraction, SUVA has enforcement powers to order an immediate shutdown of the hazardous operations until adequate technical systems are installed. Cantonal joint committees for building and civil engineering concurrently monitor compliance with collective labour agreements (CLAs), ensuring workers' health is not compromised by a lack of indispensable equipment investment. An infringement report issued during a joint body or federal inspection directly engages the liability of company management and can lead to heavy administrative penalties.
European standard EN 60335-2-69 and HEPA H14 filters in the Swiss context
Regulatory dimensioning of industrial dust extractors in Switzerland is governed by EN 60335-2-69, which specifies particular requirements for vacuum cleaners and industrial dust extractors. This standard categorises equipment into three distinct classes based on the maximum allowable permeability of their filtration system and the toxicity of the extracted substances:
- Class L (Low risk): filtration designed for simple dusts without specific respiratory toxicity, exhibiting a maximum filter permeability value of 1 % or less. This class is strictly prohibited on Swiss construction sites for cutting, grinding, chiselling or chasing mineral materials.
- Class M (Medium risk): filtration featuring a maximum permeability of less than 0,1 %. According to the guidelines in the SUVA Mineral dusts publication, Class M is the mandatory minimum standard for all work involving concrete, cement screeds, tiles, stoneware, sand-lime brick or plaster. The unit must incorporate an airflow monitoring system that alerts the operator as soon as flow velocity drops below 20 m/s.
- Class H (High risk): very high efficiency filtration with a maximum permeability rate strictly below 0,005 %. This class is required for carcinogenic or pathogenic dusts, lead-bearing residues, artificial vitreous fibres and high-concentration quartz dust.
- HEPA H14 absolute filtration: defined by particulate retention protocols with an arrestance efficiency greater than or equal to 99,995 % for the most penetrating particle size. Extractors and air scrubbers fitted with HEPA H14 filters represent the ultimate technical tier required in sensitive zones, decontamination work, and refurbishment projects in hospitals or occupied premises.
Engineering protocol and four-step specification method
To ensure the technical and legal compliance of a Swiss construction site, site management and company directors must apply a systematic equipment selection protocol. Improvising when choosing an industrial dust extractor leads to contractual disputes, chronic health hazards and uncontrolled operational cost overruns.
Step 1: Particle size risk analysis and mineral dust characterisation
The first step involves identifying precisely what materials make up the structure subjected to mechanical work. Mineral dust does not all pose the same biological hazard: the respirable fraction of crystalline silica (quartz), produced when sawing reinforced concrete, penetrates deep into the respiratory tract and causes irreversible damage such as silicosis or chronic obstructive pulmonary disease. The SUVA publication "Mineral Dust" serves here as the reference guide to assess the risk linked to respirable quartz.
The technical assessment must quantify the expected volume of fine debris per working day, the level of confinement of the workspace (windowless basement area, closed trench, naturally ventilated floor), and whether any associated hazardous substances are present, such as old bituminous adhesives or suspicious coatings. If any doubt remains regarding the composition of the wear layers, a prior diagnostic survey must clear up any uncertainty before selecting the mechanical extraction setup.
Step 2: Sizing airflow and vacuum pressure, and selecting the dust extraction class
Equipment selection relies on strictly matching the air handling performance of the motor unit to the specifications of the connected power tool. An undersized extractor leads to lateral dust leakage right from the edge of the guard hood. Volumetric airflow (expressed in litres per minute or cubic metres per hour) determines the capture capacity of the air stream at the emission point, while static vacuum pressure (expressed in hectopascals or millibars) ensures the suction force needed to pull dense dust through the rough inner surface of the hose.
For angle grinders fitted with diamond discs of 125 mm diameter or larger, an actual extraction airflow of at least 3 500 to 4 000 l/min is technically essential to maintain the regulatory velocity of 20 m/s inside a 35 mm internal diameter hose. The extraction class follows directly from this analysis: Class M is the non-negotiable minimum threshold for structural work and finishing work in Switzerland, while Class H is required as soon as the expected respirable quartz concentration exceeds action limits or when confirmed carcinogens are present.
Step 3: Checking active safety devices and automatic filter cleaning
The effectiveness of an industrial dust extractor depends directly on maintaining a constant active filter surface area. During concrete surfacing, micro-dust clogs the pores of the filter media in less than two minutes of continuous work without corrective mechanical action. Extractors with purely manual cleaning systems (reverse-air push buttons) must be strictly banned on professional construction sites, as operators under time pressure systematically skip using them in the field.
Specifications must require permanent automatic filter cleaning systems operating by reverse electromagnetic pulse or alternating counter-current airflow. These mechanisms clean the cartridges in turns without interrupting extraction or causing a noticeable drop in vacuum pressure. In addition, under standard EN 60335-2-69, the extractor must feature a differential pressure gauge or dynamic pressure sensor coupled with a visual and audible alarm. This sensor alerts the user as soon as airflow drops below the safety threshold calculated for the connected hose diameter.
Step 4: Formal documentation, traceability, and inclusion in construction site records
The final stage of the protocol involves putting the selected prevention measures in writing. In the construction site safety plan, the contractor records the model details of the dust extractors assigned to each workstation, the calibration certificates for the warning sensors, and the procedures for disposing of collected dust. Mineral dust collection bags must provide a dust-tight seal upon removal to eliminate any risk of accidental spills when handling them around sorting skips.
Technical data sheets for the filters used (in particular HEPA H14 certificates of conformity where required) must be appended to the technical documentation submitted to site management. This thorough documentation protects the firm during SUVA inspections or technical expert assessments following dust emission complaints from neighbours or other trades working alongside each other on the same area.
Comparative matrix of dust extraction and air purification equipment
The table below summarises the equipment categories used on Swiss construction sites, their regulatory specifications under technical standards, and the mandatory check points upon delivery to the site.
| Equipment family | Regulatory requirement and classification | Typical usage on a Swiss construction site | Technical check point upon delivery |
|---|---|---|---|
| Light workshop vacuum (Class L) | Standard EN 60335-2-69, maximum permeability below 1%. | Final cleanup of solid wood sawdust, coarse floor sweepings free of mineral content. | Verifying that it is strictly never connected to tools working on stone, brick, or concrete. |
| Standard power tool extractor (Class M) | Standard EN 60335-2-69, permeability below 0,1%, audible airflow alarm. | Sanding plaster, cutting plasterboard sheets, small-diameter intermittent core drilling. | Verifying the automatic power tool socket and checking that the acoustic alarm triggers below 20 m/s. |
| Heavy-duty extractor with automatic filter cleaning (Class M) | Standard EN 60335-2-69 and SUVA publication "Mineral Dust", reinforced polyester filter media. | Chasing clay bricks, concrete slab surfacing, chipping and sanding cement screeds. | Checking automatic pulse-cleaning cycles and the tightness of the container seal under vacuum. |
| High-safety extractor for toxic dust (Class H) | Standard EN 60335-2-69, maximum permeability below 0,005%, sealed container. | Milling old contaminated coatings, sanding dense mineral paints, fine quartz dust. | Checking individual filter inspection certificate and verifying integrity of the sealed safety bag. |
| Decontamination extractor with absolute filtration (Class H / HEPA H14) | Standard EN 60335-2-69 and HEPA H14 specification, certified retention of 99,995% or higher. | Major refurbishment work, handling highly toxic dust, and active healthcare facilities. | Air leakage test, checking the sealing plug on the suction inlet, and filter traceability. |
| Mobile negative air machine | Combined coarse pre-filtration stages and HEPA H14 final cartridge. | Maintaining negative pressure in closed renovation areas, capturing residual airborne aerosols. | Measuring differential pressure across the HEPA cartridge and checking air change rates. |
Technical selection criteria and operational requirements for site management
Beyond the theoretical rating of the dust extractor, day-to-day performance on the construction site hinges on specific electromechanical parameters that site management must check when reviewing the execution equipment proposed by successful bidders.
The first criterion is the antistatic compatibility of the extraction line. Continuous friction from silica particles moving at high speed along the polymer walls of a hose generates static electricity that can reach high voltages. These sudden discharges are unpleasant for craftsmen, but above all they cause control electronics to fail and raise the risk of ignition in environments containing flammable microparticles. Specifying a conductive hose grounded via the earth pin of the Swiss mains plug (T12/T23 depending on current rating) is essential for continuous surface grinding work.
The second key factor is the type of collection bag fitted in the container. Standard paper bags tear under the stress of an airflow loaded with sharp mineral fragments and must be ruled out entirely. For Class M use on concrete, tear-resistant multi-ply synthetic non-woven bags are the standard choice. When dealing with fine dust rated Class H, using a safety bag with a heat-sealable outer liner or an integrated adhesive closure prevents any skin contact or inhalation when swapping bags at the end of a shift.
The third criterion concerns the layout of the built-in automatic power tool socket on the extractor. This electronic unit senses when the auxiliary power tool (sander, wall chaser, circular saw) is switched on and starts the suction turbine automatically with a slight delay of a few seconds. When the cutting tool stops, the turbine keeps running for around five to seven seconds to clear the flexible hose completely of suspended mineral residue, preventing dust from dropping onto the floor when disconnecting.
Finally, deploying mobile negative air machines supplements source capture when work takes place in occupied buildings or spaces where full containment is not feasible. By pairing a Class M dust extractor connected to the tool guard with a mobile air scrubber fitted with a HEPA H14 final cartridge—either ducting filtered air outside or recirculating it at an air change rate matched to the room volume—the contractor ensures strict compliance with Swiss occupational health standards and provides lasting protection for all workers on the construction site.
Standard dust extraction package by construction site setup
Sizing industrial extraction and mobile air cleaning equipment requires careful adjustment to room layouts, confinement levels, and the mineral composition of the generated dust. Selecting extraction units that meet EN 60335-2-69 and incorporating HEPA H14 final filters do not involve the same logistical constraints on an open-weather structural work shell as they do inside an occupied commercial building. To assist site management and site managers, the following reference table outlines the minimum equipment requirements across standard operational situations encountered in Switzerland.
| Site situation | Typical dust-generating tasks | Type of mineral dust | Recommended equipment package | Required filtration units and accessories |
|---|---|---|---|---|
| Structural work and covered earthworks | Bush-hammering, heavy core drilling, concrete slab sawing, kerb cutting | Quartz, silicates, cement aerosols of varying grain sizes | Class M site dust extractor with automatic pulse cleaning | Twin treated-polyester pleated filters, reinforced polyethylene disposal bag, direct tool-triggered auto-start |
| Finishing work and building services | Chasing sand-lime bricks, repetitive drilling, sanding plaster | Fine respirable crystalline silica fractions, calcium sulphate | Compact Class M auto-start extractor with audible and visual airflow alarms | Class M cartridges with automatic filter cleaning, sealable non-woven filter bag, large-diameter antistatic hoses |
| Major renovation in occupied premises | Stripping bonded screeds, grinding levelling compounds, demolishing partitions | Very fine mineral dust and aged polymer adhesives | Two-part setup: Class M extractor at the source and mobile HEPA H14 air scrubber | Sealed containment airlock, continuous negative pressure, HEPA H14 absolute terminal filter on the air scrubber |
| Work at height on scaffolding | Grinding fair-faced concrete on façades, low-pressure slurry blasting | Cement flour, ultra-fine quartz from façade aggregates | Reinforced compact Class M extractor or remote unit at the base of the riser | Mechanically secured antistatic suction hose, cable suspension harness, sealed collection bag |
| Confined spaces and underground utility tunnels | Track-mounted wall sawing, deep core drilling, underpinning | Highly concentrated airborne mineral dust, residual moisture | Dedicated Class M central extraction unit with cyclonic pre-separator | Intermediate cyclonic filter for moist dust, ducted exhaust venting filtered air outside the tunnels |
Allocation requirements by construction phase
On structural work projects, the usual mistake is underestimating the mass of material extracted during sawing or grinding of large surfaces. Direct extraction at source requires units capable of handling high mass volumes without a drop in static pressure. The systematic use of automatic filter cleaning via airflow reversal or electromagnetic pulses is essential to maintain capture velocity at the safety guard of floor saws and surface grinders.
In technical finishing work, electricians, plumbers and plasterers face intermittent but steady emissions of highly aggressive quartz dust from brick and gypsum blocks. Mobile dust extractors must feature a compact footprint while incorporating an automatic power take-off socket with sufficient rated output to run twin-blade wall chasers without tripping temporary site distribution boards.
For renovation projects carried out around building occupants or in adjacent occupied premises, extraction at source on power tools must imperatively be paired with comprehensive air cleaning. Using an air scrubber equipped with a pre-filtration stage and an end-stage HEPA H14 filter alongside extraction ensures residual particles escaping collection shrouds are intercepted, preventing mineral dust from migrating outside the work enclosure.
Acceptance protocol, delivery checklist and commissioning
Bringing new dust extraction equipment onto a construction site must never happen without a formal technical check. As soon as the unit is supplied by the hire firm or the contractor's plant department, systematic inspection prevents putting non-compliant units or equipment damaged on previous jobs into service. In accordance with art. 5 OTConst, on every construction site the employer designates a competent person responsible for occupational safety and health protection who is authorised to issue directives to workers; this person systematically inspects the unit before any use.
Technical acceptability checklist for dust extractors
- Rating plate and standard markings: Verification of compliance with standard EN 60335-2-69, showing a clearly visible official dust class label (legible manufacturer marking stating "Class M" or "Class H"). Class L units or units without markings are strictly barred for capturing mineral quartz dust.
- Mechanical integrity of housing and latches: Inspection for cracks on the reinforced polypropylene motor head, check of the peripheral sealing gasket between drum and head, and verification of the clamping force of toggle latches.
- Presence and condition of filter elements: Direct visual inspection of filter cartridges. Exclusive presence of filters compliant with the machine's specifications, free from tears, frame deformation, or hardened wet deposits within the filter media pleats. For HEPA H14 units, verification of the individual factory test certificate.
- Airflow volume monitoring system: Functional testing of the integrated acoustic or visual alarm. Deliberate, full obstruction of the suction inlet using a test plug must trigger the alarm within the time specified in the instruction manual, demonstrating differential pressure sensor sensitivity.
- Operational automatic filter cleaning: Starting up the unit and checking the cyclic shaking or air-reversal pulse by ear and sight, ensuring cartridge cleaning takes place without interrupting extraction airflow.
- Accessories and hoses: Inspection of the antistatic extraction hose for crushing or punctures, and verification of a full set of sealed reducers matching tool hoods for the cutting or drilling equipment planned on site.
- Collection bags and disposal procedure: Presence inside the drum of a dedicated, sealable collection bag allowing extraction and dust-tight closure without re-suspending dust into the air during emptying.
Illustrative practical cases (typical scenarios on Swiss construction sites)
The following cases are illustrative scenarios designed to model representative operating conditions in Switzerland, and do not describe actual projects. They show the technical reasoning, machine selection criteria, and foreseeable financial costs for site management.
Standard Scenario 1: Heavy renovation of an office complex in Lausanne (Canton of Vaud)
A general contractor oversees the complete overhaul of two office floors in a downtown Lausanne commercial property. The scope involves cutting concrete slabs to create service shafts and mechanically surfacing 850 m² of bare slabs prior to laying mineral floor coverings. The team comprises 6 workers continuously deployed on structural work and interior masonry phases.
The nature of the reinforced concrete substrate and the intensity of partial demolition work demand managing high quartz dust concentrations. Pursuant to art. 365 CO, the contractor is liable for the sound quality of materials supplied and the suitability of working methods and equipment. To safeguard working conditions and prevent contaminating building risers that remain partially occupied, site management specifies the following setup:
- Two three-phase Class M industrial vacuum extractors with electromagnetic automatic filter cleaning for slaving floor grinders and concrete cut-off saws.
- Four compact single-phase Class M dust extractors for secondary chipping and drilling into sand-lime block partitions.
- Two mobile laminar-flow air scrubbers fitted with end-stage HEPA H14 filters, maintaining work floors under negative pressure to capture airborne ambient aerosols.
The overall budget estimate for the dust extraction fleet on this standard scenario—covering 8 weeks of equipment provision, filter consumables, and periodic technical checks—stands in the region of 8 400 CHF excluding tax, or approximately 9 080 CHF including tax at the statutory Swiss VAT rate of 8,1 %.
Standard Scenario 2: Refurbishment of a school facility in Meyrin (Canton of Geneva)
As part of the thermal and acoustic upgrading of a municipal school building erected in the 1970s, a plastering, painting, and masonry firm removes old interior rendering and sands wall levelling compounds. The assigned crew consists of 4 workers operating in enclosed spaces with no natural ventilation.
Prior to starting, the employer ensures compliance with health and safety procedures. Under art. 4 OTConst, before work begins, the employer ensures there is a plan detailing the necessary measures for the work carried out on the construction site, including the organisation of first aid. Given the extremely fine particle size of synthetic binders and micro-silica fillers found in historical decorative coatings, and to eliminate risks associated with complex mineral dust, the firm implements a high-security approach:
- Two certified Class H extraction units with factory-fitted end-stage absolute HEPA H14 filtration and dual containment using heat-sealable disposal bags.
- Mandatory tool slaving of drywall sanders and wall chasers via synchronised power sockets on the Class H units, preventing abrasive tools from running unless effective suction airflow is established.
- Weekly cartridge permeability testing logged in the construction site safety register.
The benchmark cost for outfitting this representative project over 4 working weeks—covering rental of two Class H units, dedicated containment bags, and heavy-duty antistatic hose assemblies—represents a budget around 3 950 CHF excluding tax, or roughly 4 270 CHF including tax (8,1 % VAT).
Recurring operational errors and consequences on construction sites
Site feedback from Swiss construction sites highlights several recurring technical bad practices that wipe out the performance of air capture equipment and expose workers to serious hazards:
Using Class L extractors for concrete and masonry work
Confusing standard workshop vacuums with heavy-duty construction site extractors remains common. Class L vacuum cleaners are certified solely for dust considered low risk and show filtration leakage rates that are unacceptable for quartz dust. Using a Class L machine during concrete sawing instantly exhausts the finest mineral particles back into the room, directly respirable into pulmonary alveoli, while giving workers a false sense of protection.
Deactivating or bypassing automatic filter cleaning
On equipment subjected to a continuous load of concrete dust, some workers turn off the automatic filter cleaning system because of the pulsing noise or lack of training. Without vibration or reverse air pulsing, the outer surface of the filter cakes over in minutes with a dense crust of dust. Effective suction collapses, capture velocity at the tool drops to virtually zero, and dust is blown into ambient air instead of entering the hose.
Emptying drums by tipping directly into open air
Emptying a bagless extractor drum by tipping it over an open site skip is strictly prohibited. This practice generates a concentrated cloud of mineral dust that directly exposes both the worker and anyone downwind. Professional standards require using exclusively sealable bags or hermetic bagging systems before any handling.
Contractual and administrative consequences
Using defective or non-compliant equipment jeopardises project execution. Under art. 366 CO, if it is certain through the contractor's fault that the work will be executed defectively or contrary to the contract, the client may set a reasonable time limit with notice that, upon expiry, repairs or continuation of the work will be entrusted to a third party at the contractor's expense and risk. Moreover, deliberate disregard of recognised technical rules on ambient air safety may trigger criminal liability under art. 229 CP, which penalises anyone who, in directing or executing a construction or demolition, intentionally breaches the rules of the trade and knowingly endangers the life or physical integrity of others.
Preventive maintenance, life cycle and filter cartridge replacement
Maintaining certified performance under EN 60335-2-69 requires a rigorous maintenance routine throughout the operational life of the unit. A clogged or improperly serviced dust extractor loses its original filtration properties and turns into a diffuse source of mineral pollution.
Periodic inspections and safe cleaning
At the end of each working shift, the worker or the plant manager must inspect the machine for visible fouling. Cleaning the dust extractor itself must never be done with compressed air or blowguns, which instantly re-suspends hazardous dust into the air. The outer casing must be cleaned solely with a damp cloth or by surface vacuuming using a second, compliant extraction unit.
Filter media replacement schedule
Class M cartridges or HEPA H14 cassettes must be replaced as soon as any of the following occurs: persistent low airflow alarm after a full automatic cleaning cycle, visible punctures in the filter pleats upon inspection, or compromised mechanical strength caused by accidentally vacuuming wet core-drilling slurry. To carry out filter replacement without mineral dust emissions, the operator must work in a ventilated area, seal the spent cartridge immediately in the manufacturer-supplied synthetic bag, and close it using a cable tie before compliant disposal in the appropriate inert or mineral waste stream. Every maintenance operation and main filter change must be signed off in the equipment service log, ensuring complete traceability during site technical audits.
Free construction site calculators
Thirty-five trade calculators: site installations, waste, concrete, screeds, insulation, scaffolding. No sign-up required.
Frequently asked questions
What is the regulatory difference on Swiss construction sites between a class M and a class H dust extractor?
On Swiss construction sites, the distinction is based on certified permeability under standard EN 60335-2-69 and toxicity as defined by SUVA Mineral Dusts. Class M filters quartz and concrete dust with a permeability of less than zero point one per cent. Class H is mandatory for carcinogenic dusts such as asbestos, requiring a permeability of less than zero point zero zero five per cent with a HEPA H14 stage. Purchasing a class H unit represents an indicative cost in the region of 1450 CHF excl. VAT, compared to 850 CHF for class M.
Why are class L dust extractors systematically rejected by SUVA for mineral grinding or cutting?
Class L units have a tolerated permeability of one per cent and lack an airflow warning device. When grinding concrete or masonry, quartz concentrations immediately exceed exposure limit values. The Ordinance on Accident Prevention prescribes equipment meeting state-of-the-art standards. Art. 18 OLT 3 governs air pollution in the workplace. When dealing with hazardous mineral dusts, only class M or H guarantees sufficient filtration to prevent a site shutdown ordered by inspectors.
Why is an audible airflow warning device under standard EN 60335-2-69 mandatory on class M and H units?
Standard EN 60335-2-69 requires an audible or visual warning to trigger as soon as the air speed in the hose drops below the manufacturer's set threshold. This monitoring alerts the operator to a clogged filter, a crushed hose or a full dust bag. Without this mandatory alarm, extraction flow collapses without any visible sign, leading to massive leakage of mineral dust into the breathing zone. This automatic monitoring reliably and durably protects workers' health on Swiss construction sites.
Why is automatic pulse filter cleaning essential when working on concrete and natural stone?
Dust generated by core drilling or surface grinding quickly clogs standard filter cartridges. An auto-start extractor equipped with automatic filter cleaning cleans its filters continuously using shaking or reverse air pulses, without interrupting extraction at the connected tool. This technology maintains constant negative pressure at the machine shroud. While this system involves an indicative extra purchase cost of around 350 CHF, it eliminates forced downtime and prevents the harmful dispersion of respirable silica particles into the immediate surroundings.
What is the legal procedure in Switzerland upon the unexpected discovery of materials containing asbestos?
As soon as a suspect material is uncovered unexpectedly during work, the team must halt work and notify site management. Art. 82 OTConst requires that work releasing a substantial quantity of health-hazardous asbestos fibres must only be carried out by asbestos abatement companies recognised by CNA. A standard class M dust extractor is prohibited: only a class H unit fitted with a HEPA H14 filter ensures the essential technical safety before any resumption of operations on the construction site.
How should air purification requirements be integrated into preparatory site planning?
Art. 4 OTConst provides that prior to starting work, the employer shall ensure there is a plan detailing the measures required for the work carried out on the construction site, in writing or in a form that allows text proof. Art. 5 OTConst para. 1 requires the appointment of a competent person authorised to issue direct instructions. This document specifies the use of auto-start class M dust extractors and procedures for handling airtight bags to eliminate the inhalation of hazardous respirable particles.
What obligations fall upon the contractor if asbestos-containing materials jeopardise contractual progress?
Under art. 365 CO para. 3, if any circumstance arises that compromises the proper or timely execution of the work, the contractor must inform the client immediately, failing which they shall bear the consequences. When an unforeseen concentration of hazardous dust requires shutting down the construction site, this formal notice shields the firm from liability. Extra costs relating to the deployment of air scrubbers, around 140 CHF per operating day, are recorded in the site journal. Standard SIA 118 sets out the terms for compensation and extensions of contractual deadlines.
What criminal penalties do site managers risk in the event of serious disregard for dust extraction rules?
Art. 229 CP penalises breaches of the recognised rules of building and construction. Anyone who intentionally violates these rules while executing or supervising construction work, knowingly endangering the life or physical integrity of others, is liable to a custodial sentence not exceeding five years or a monetary penalty, or up to three years through negligence. Deliberately bypassing dust extraction systems during intensive concrete cutting, thereby creating an environment saturated with toxic particles, exposes management personnel to these precise criminal penalties.
Summary of specifications and implementation resources
Managing air quality on Swiss construction sites ensures operative safety, legal compliance and uninterrupted site operations. To explore each technical aspect in detail and select your equipment in line with current directives, consult our specialist guides:
- Class M Dust Extractor (Swiss Site Standard) vs Class H Asbestos: OEL Values and Obligations During a SUVA Inspection
- Power-Tool Triggered Dust Extractors with Automatic Filter Cleaning: Working Without Suction Loss on Wall Chasers and Concrete Grinders
- Mobile Negative Air Units: Containing Dust in Occupied Renovation Sites
- Regulatory Swiss Construction Site Vacuum Cleaner Selector (Class L, M or H / HEPA H14) Based on Dust & SUVA OELs