Skip to content
Sign in Sign up
Categories
Power tools DrillsScrewdriversGrindersSaws Measure Laser levels Protection Protective equipment Site Ladders and stepladdersHand tools
Support
Change language: French
Practical guide

Diamond Blade Mechanics: Why Swiss Granite Requires a Soft Bond and Asphalt a Hard Bond

How to choose between soft and hard bond diamond blades in Switzerland. Technical review for granite, reinforced concrete and asphalt under SIA 118.

Table of contents
The 3 Major Site Risks
  1. Financial / Margin: Using a hard-bond segment on very hard stone such as granite leads to instant glazing of the synthetic diamonds. The resulting drop in output creates premature wear and additional labour costs of around 15 to 30 % on cutting items under SIA 118.
  2. Legal / Joint Body / SUVA: Dry-cutting reinforced concrete without dust extraction or water suppression exposes the crew to respirable crystalline quartz dust. Under art. 33 OTConst and art. 82 LAA, employers must exhaust, filter or ventilate ambient air, failing which work may be halted by SUVA.
  3. Administrative / Handover: Using unsuitable tools that cause micro-structural cracks on precast components or granite kerbs exposes the contractor to delivery delays and client claims under art. 364 CO.

Selecting the metal matrix of a diamond segment relies on the principle of controlled bond wear through self-sharpening. On Swiss civil engineering and building construction sites, cutting-tool selection governs both operator safety and the profitability of measured items quoted under the CAN. A mismatch between substrate hardness and segment alloy composition leads either to binding through glazing caused by insufficient matrix wear, or to ultra-rapid erosion resulting in the hazardous release of synthetic diamond crystals.

This technical guide is aimed at site management teams, masons and concrete-sawing specialists seeking the optimum balance between cutting speed and tool life. Given the wide variety of siliceous aggregates and bituminous mixtures found across Western Swiss cantons, understanding the tribological response of soft and hard metal bonds is an essential prerequisite for carrying out cuts in line with the recognised rules of construction and SUVA occupational health requirements.

Tribology of diamond segments: self-sharpening mechanism and alloy matrix

The core principle of diamond sawing lies in continuously renewing the cutting edges. Synthetic diamonds are held in place by a metal matrix made from sintered cobalt, bronze, tungsten or iron powders. During cutting, abrasive slurry rubs against this bond and wears it down at a calibrated rate. This progressive erosion exposes fresh diamond edges as earlier ones become blunt or fracture. Selecting the alloy hardness follows an inverse rule: the harder and less abrasive the material to be cut, the softer the bond must be; conversely, the more abrasive and softer the material, the harder the bond must be.

On Swiss construction sites, cutting granite quarried in the Alps requires an ultra-soft bond. Granite contains a high proportion of hard quartz that blunts diamond grits very quickly. A soft bond wears away fast enough to shed these worn diamonds and immediately expose fresh, sharp crystals. If the site management or the mason uses a hard bond on granite, the matrix does not wear fast enough. The diamonds become blunt without being released, the segment smooths over and the blade glazes. This overheating warps the steel core and creates a major risk of blade breakage.

Conversely, asphalt or green concrete are highly abrasive materials with low contents of hard silica. Asphalt dust acts like coarse-grit sandpaper on the matrix. When cutting pavements, using a soft bond causes premature segment erosion. The bond strips away before the diamonds have had time to work, wearing out the blade entirely within a few metres of cut and causing a direct financial loss of several hundred CHF. For this type of substrate, using a matrix heavily loaded with hard bond materials or wear-resistant tungsten carbide is essential.

Regulations and health protection during dry and wet cutting

Cutting reinforced concrete, masonry or granitic rocks generates heavy concentrations of respirable crystalline silica dust. Under art. 82 LAA, employers must take all measures to prevent occupational accidents and illnesses shown by experience to be necessary, feasible according to the state of technology and adapted to prevailing conditions. For its part, art. 3 OPA requires employers to take protective measures that comply with the ordinance, with other applicable workplace safety rules and with recognised technical safety standards.

Regarding air quality at cutting stations, art. 33 OTConst requires ambient air at workstations to contain between 19 and 21 % oxygen by volume and dangerous substance limit values not to be exceeded. This article specifies that dangerous substances must be evacuated to the open air, filtered or diluted through mechanical ventilation, and that respiratory protective equipment must be worn if technical or organisational measures prove insufficient. Furthermore, art. 18 OLT 3 governs air pollution in workplaces. Continuous wet cutting or connecting the power cutter directly to an industrial class M or H vacuum cleaner represents the technical standard for complying with these requirements.

Noise generated by diamond blades spinning at high speed and diamonds impacting the substrate is governed by art. 36 OTConst. This article provides that where noise exposure cannot be brought below threshold values through technical or organisational measures, suitable hearing protection must be worn. Art. 22 OLT 3 addresses workplace noise and vibrations, requiring them to be eliminated or controlled through construction measures, equipment design, insulation or work organisation. Art. 27 OLT 3 covers personal protective equipment that workers must wear every day.

Regarding overall organisation and safety, art. 4 OTConst requires that, before work starts, the employer ensures a plan detailing the measures required for works carried out on the construction site exists in writing or in a form verifiable by text. Art. 5 OTConst specifies that the employer must appoint a competent person on each construction site in charge of occupational health and safety who is authorised to give instructions to workers. In the event of serious breaches of the rules of the trade endangering workers' lives, site supervisory staff face criminal liability under art. 229 CP.

Comparison table for diamond blade selection according to CAN materials

Material to cutHardness / AbrasivenessRecommended bond typeStandard & safety requirementSite management checkpoint
Swiss granite / GneissExtreme hardness / Low abrasivenessUltra-soft bond (bronze-powder alloy)Art. 82 LAA (equipment adapted to the state of technology)Check for absence of diamond glazing and ensure appropriate rotational speed.
High-density reinforced concreteHigh hardness / Medium abrasivenessSoft to medium-soft bondArt. 33 OTConst (dust extraction or filtration)Monitor rebar cutting to prevent overheating of the steel blade core.
Porcelain stoneware / 20 mm quartz slabsVery high hardness / Brittle materialSoft bond continuous rim / TurboArt. 36 OTConst (wearing hearing protection)Inspect cut edges to prevent chip micro-cracks.
Bricks / Clay masonryMedium hardness / Medium abrasivenessUniversal bond (medium hardness)Art. 3 OPA (applying safety regulations)Ensure the protective guard is fitted on the power cutter.
Asphalt / Green concrete (< 24h)Low hardness / Extreme abrasivenessExtra-hard bond (tungsten-iron alloy)OMach (machinery and mounted tooling safety)Check for protective undercut segments preventing steel core undercut wear.

Common tooling selection mistakes and their direct financial impact on quotes

Confusing material hardness with bond hardness is the most expensive purchasing mistake seen on Swiss construction sites. Using a general-purpose hard-bond blade to cut Alpine granite kerbs glazes the blade after just two metres of cutting. Operators then tend to force the tool, applying excessive pressure. This poor practice overheats the steel core, causing axial distortion and releasing sintered segments. For a three-man masonry crew on a civil engineering construction site, lost time and premature replacement of ruined blades result in direct additional costs of around 450 CHF to 1 200 CHF per day in wasted labour and tooling.

Another frequent mistake is dry-cutting asphalt using a blade designed for wet concrete cutting. Without lubrication and with an overly soft matrix, abrasive particles strip the bond in minutes. The segments lose their diamonds before wearing down normally. Direct costs of abnormal consumable wear quickly reach about 350 CHF for every 10 metres of non-compliant cutting. Purchasing laser-welded segmented blades fitted with deep-drop segments against steel core undercutting prevents these premature failures and protects yields budgeted in the CAN quote.

Illustrative practical cases (typical scenarios on Swiss construction sites)

The following scenarios are illustrative examples designed to guide consumable selection on construction sites in Western Switzerland. The figures and durations provided are indicative reference benchmarks.

In the canton of Vaud, on an urban development site in Lausanne involving the installation of granite kerbs from the canton of Ticino, an 8-worker masonry company had to perform 450 linear metres of adjustment cuts. The crew initially fitted their power cutters with a hard-bond universal blade. After 15 metres of cutting, the blades glazed over, halting progress. Following an analysis of the granite's mineral matrix, site management specified soft-bond laser-welded blades used with wet cutting. This change restored required cutting speeds, lowered specific wear and averted a delivery delay valued at 2 800 CHF in labour.

In the canton of Geneva, during a highway engineering structure repair requiring 120 metres of cutting in bituminous asphalt and green concrete, the plant operator chose a hard-bond blade reinforced with slanted undercut-protection segments. This technical choice shielded the segment base from the abrasive effect of asphalt sand. By complying with art. 4 OTConst through a suitable safety plan and applying art. 33 OTConst with a water suppression system coupled with a slurry collection tank, the firm completed all trench cuts without a single premature blade replacement, keeping the tooling budget within the planned envelope of 1 450 CHF.

Free construction site calculators

Thirty-five trade calculators: site installations, waste, concrete, screeds, insulation, scaffolding. No sign-up required.

View trade calculators

Frequently asked questions

Why does an asphalt diamond blade dull immediately in Swiss granite?

Abrasive asphalt requires a hard metal matrix to prevent premature diamond loss. Faced with the hard, dense quartz of Valais granite, this rigid bond fails to erode. The diamond crystals blunt without renewing, causing mechanical glazing, overheating and an output loss estimated at several hundred CHF in daywork under SIA 118.

What is the financial risk of using a soft-bond blade on bituminous mixtures?

Abrasive silica fines attack prematurely soft bonds designed for hard rock. The diamond segments are literally stripped away within a few linear metres. This premature destruction of the tooling causes a direct loss of around 350 CHF per blade, violating the contractor's contractual duty of care under art. 364 CO.

How does bond selection prevent serious accidents on petrol cut-off saws?

A bond that is too hard on reinforced concrete generates excessive friction, glazes the segment and drives temperatures beyond laser-welding tolerances. The risk of metallic element failure becomes critical. Matching the matrix to the material complies with the general prevention rules set out in art. 82 LAA for cutting tools.

What dust extraction requirements apply when cutting sandstone or concrete?

Dry diamond cutting of mineral materials releases respirable crystalline silica dust. Under art. 33 OTConst, the employer must exhaust or filter hazardous dust, or use a cut-off saw with a continuous water supply. In the absence of adequate technical remediation, wearing suitable respiratory protective equipment remains strictly mandatory to protect personnel.

What should you do on a construction site when a new diamond blade begins to spin without cutting?

This indicates matrix glazing. You must redress the segment immediately by making three short passes into a sand-lime brick or highly abrasive asphalt. This controlled friction strips the glazed surface layer of hard bond and exposes fresh diamond grits without damaging the steel core complying with OMach, RS 819.14.

Who bears the extra cost of diamond blade wear during unforeseen cutting work?

If the contractor encounters extremely hard river aggregates not described in the specifications, they must notify site management pursuant to art. 365 CO. Under a fixed-price contract governed by art. 373 CO, no price increase is permitted without proven extraordinary circumstances, making the tracking of consumables essential to justify compensation on a daywork basis.

Optimising cutting performance and safety depends on a strict mechanical balance between the hardness of the metal bond and the abrasiveness of the sawn material. To take your technical analyses further and equip your teams in line with Swiss civil engineering standards, explore our dedicated resources:

Art Construction is an independent company: it is not affiliated with the SIA, CRB, SUVA, or KBOB. Referenced norms and standards point to publications from these bodies; only official versions are legally binding.