Table of contents
The 3 Major Site Risks
- Financial / Margin: A mismatch between the hardness of a diamond blade's matrix and the material to be cut causes immediate glazing or premature wear of the abrasive segments. Using a hard bond on concrete reinforced with Valais quartz or Ticino granite prevents the synthetic diamond grit from being exposed, triggering a drop in linear output that can exceed 65 % and tripling the hourly machine cost. This equipment cost overrun and the unplanned extension of labor hours on slab core drilling represent operational losses estimated for illustrative purposes in the range of 4 500 CHF to 12 000 CHF per heavy sawing phase. Under art. 364 CO, the contractor procures at its own expense the means, plant and tools required for the proper delivery of the agreed services, without financial compensation from the client.
- Legal / Joint Body / SUVA: Dry cutting or core drilling without extraction devices and integrated water feed saturates the atmosphere with respirable crystalline quartz silica dust, causing severe respiratory damage and immediate formal notice during joint-committee and cantonal inspections. Under art. 3 OPA, the employer takes the protective steps and measures that comply with the provisions of the ordinance, with other applicable occupational safety regulations and with recognized rules of safety technology and occupational medicine. Art. 33 OTConst mandates that ambient air at workstations contain between 19 and 21 % oxygen by volume and that hazardous substances be discharged into the open air, filtered, or diluted by mechanical ventilation. In the event of a mechanical accident linked to the failure of a brazed segment or projectile ejection, art. 229 CP imposes criminal penalties on anyone who intentionally or through negligence breaches the recognized rules of the trade, thereby endangering bodily integrity.
- Administrative / Acceptance: Using uncertified drilling tools produces out-of-round anchor holes or boreholes that exceed dimensional tolerances, jeopardizing the load transfer of injected reinforcing bars and heavy structural anchors. During inspections of civil engineering structures or pile caps, the site management and civil engineers reject the compliance of structural anchoring performed outside tolerances. Pursuant to art. 367 CO, the client inspects the state of the works and gives notice of defects found. Geometric non-compliance requires the complete reconstruction of the support points at the contractor's expense, delaying the acceptance of the work governed by SIA 118 and triggering the withholding of contractual advance payments until on-site tensile pull-out tests are validated.
The systematic specification of cutting, core-drilling and drilling consumables is a decisive pillar of technical profitability and tolerance control on Swiss civil engineering and building construction sites. Project managers, site managers and procurement officers face extreme geological variability across extraction regions: molasse from the Vaud and Fribourg Plateaux, abrasive Jura limestone, alluvial aggregate concrete from the Rhône or ultra-dense Alpine granites. Selecting a diamond blade does not come down to a visual diameter check, but to the precise metallurgy of the bond holding the diamond crystals. According to the physical law of inverse abrasion, a soft metallic bond based on bronze or cobalt is essential when sawing very hard rock to continuously release fresh cutting edges, whereas a hard tungsten carbide or alloy steel bond is necessary to withstand the destructive scouring effect of bituminous asphalt and liquid cement screeds. Any failure to balance this relationship results in tool glazing, core overheating and a major hazard of segment detachment under thermal stress.
This engineering guide details the operational compatibility criteria to make your tooling procurement reliable across French-speaking cantons. We analyze the tribological balance of wet and dry diamond core bits, the mechanical strength of laser-welded joints compliant with the safety requirements of EN 13236, and the geometric specifications of four-cutter solid carbide SDS-Plus and SDS-Max drill bits bearing PGM certification. All the installation procedures presented incorporate the dust-suppression rules of the Construction Work Ordinance (OTConst), the noise and vibration prevention directives of Ordinance 3 on the Labor Act (OLT 3), and the occupational health protection obligations mandated by art. 82 LAA. By systematically matching the bond hardness to the regional aggregate hardness coefficient, site management secures production rates, ensures the structural integrity of intersected reinforcement bars, and eliminates disputes during acceptance of the work.
Swiss regulatory framework and execution responsibilities
The use of rotary cutting and drilling tools on Swiss construction sites is governed by a rigorous interaction between federal occupational safety legislation, the law on contracts for work and services, and technical manufacturing specifications. Matching the tool to the material is not merely an economic yield variable: it governs the control of kinetic energy, mineral dust capture and the prevention of mechanical failures on high-speed rotating equipment.
The employer bears the responsibility of providing state-of-the-art equipment adapted to the specific stresses of each mineral substrate. Workers are obligated to assist the employer in applying safety instructions and to systematically use the personal protective equipment provided to them. This operational responsibility is monitored by the Swiss National Accident Insurance Fund (SUVA), which inspects workstations presenting risks of flying debris, noise exposure and inhalation of quartz dust. In parallel, cantonal joint commissions verify compliance with working conditions and the standard of tooling deployed by firms subject to the collective labor agreements (CLA) of the main construction trades.
Contractually, the contractor remains the guarantor of the proper performance of the work according to the recognized rules of the trade. Using unsuitable tools that lead to micro-cracking in the concrete cover, unauthorized cutting of structural rebar, or spalling of concrete surfaces directly engages the contractor's liability toward the client. For immovable structures, the client has a statutory 60-day period to notify defects after their discovery, under the rules governing contracts for work and services in the Code of Obligations (CO). The client's rights arising from defects have a limitation period of five years for immovable structures, which requires full traceability of all structural drilling and sawing operations.
The inherent safety of diamond blades and core bits is governed by standard EN 13236, which establishes mechanical strength requirements, maximum permissible operating speeds, and testing methods for bonded abrasive and diamond products. For structural drilling, PGM Certification forets guarantees compliance with tight geometric tolerances on the carbide head diameter, a strict prerequisite for metal anchors and chemical injection systems to achieve the design load capacities calculated by the civil engineer.
Engineering method and four-step specification protocol
Selecting a drill train or cutoff blade must never be left to chance in site logistics. A structured four-step protocol ensures technical compliance and operator safety.
Step 1: Mineralogical analysis of the substrate and risk identification
The first step consists of characterizing the mineral matrix to be worked. The free crystalline silica (quartz) content determines the abrasiveness and hardness of the substrate. Fresh concrete, liquid screeds or silica sandstones exhibit high abrasiveness that prematurely erodes soft metallic bonds. Conversely, cured reinforced concrete containing flint aggregates or dense Swiss granite requires a soft bond capable of releasing diamond grit continuously to prevent immediate glazing.
The analysis also identifies the presence of passive reinforcement or prestressing steel. Drilling or core drilling through reinforced concrete generates severe mechanical shocks whenever the cutting edge strikes a rebar. The operator faces sudden tool jamming, which generates hazardous kickback torque on upper limbs as well as hand-arm vibration. These hazards must be anticipated when planning workstations.
Step 2: Selecting the tool family and bonding method
Tool selection is based on the metallurgical balance between the bond and the target material. For diamond blades and core bits, three configurations predominate:
- Laser-welded segments: Laser beam welding offers the highest resistance to thermal and mechanical detachment. It is mandatory for dry cutting concrete and heavy masonry using petrol cut-off saws or large-diameter angle grinders, in accordance with the integrity requirements of EN 13236.
- Continuous rim or sintered turbo: Designed for fine cuts requiring clean edges with zero chipping on visible surfaces (thick tiles, porcelain stoneware slabs). The sintered bond without segment slots absorbs lateral stresses but requires adequate cooling to prevent the steel core from overheating.
- Brazed or laser-welded core drill bits: Diamond segments arranged in an annular ring allow the extraction of the central core. Silver brazing strictly requires continuous wet cutting to prevent the filler metal from melting, whereas laser-welded segments allow specific dry core drilling operations when paired with an industrial dust extractor.
For hammer and rotary-hammer drilling, the solid four-cutter carbide bit is superior to traditional two-cutter heads. The symmetrical cross geometry distributes impact energy across four distinct cutting edges, eliminating the risk of tool deviation or jamming upon head-on impact with steel reinforcement.
Step 3: Verification of compliance with normative frameworks
Before deployment on the construction site, the equipment manager or site management verifies that consumables bear permanent statutory markings:
- Marking of compliance with EN 13236 on the diamond blade core, stating the maximum operating speed in revolutions per minute (rpm), the maximum peripheral speed in meters per second (m/s), the mandatory direction of rotation, and operational restriction pictograms (dry or wet cutting).
- The presence of the official geometric mark PGM Certification forets stamped on the body of each SDS-Plus or SDS-Max drill bit. This mark certifies that the tungsten carbide head diameter falls strictly within the authorized tolerance range for the certified anchoring of engineering studs and anchors.
Step 4: Traceability, workstation instructions and technical documentation
The final step formalises the engineering decision. The contractor records the specified tool type in the execution documents for the construction site. Operators receive technical data sheets stating the recommended contact pressure ranges, minimum cooling water flow rates for wet cutting, and the type of dust extraction shroud to be connected to the certified industrial vacuum cleaner for dry work. This traceability proves the firm's technical diligence during inspections by site management or labour inspectors.
Comparative specification table for cutting and drilling tools
The table below summarises compatibility criteria, inspection standards, and critical checkpoints upon delivery of consumables on the construction site.
| Equipment family | Applicable standard or code | Typical target material on a Swiss construction site | Recommended operational use | Mandatory inspection point upon delivery |
|---|---|---|---|---|
| Hard-bond diamond blade with laser-welded segments | EN 13236 | Asphalt, bituminous surfacing, highly abrasive green concrete | Sawing road trenches, cutting pavement openings | Inspection of the undercut protection segment preventing premature steel core wear |
| Universal-bond diamond blade with laser segments | EN 13236 | B25 to B45 structural concrete, clay blocks, bricks | Cut-off sawing with angle grinders or petrol saws on structural work sites | Verification of maximum peripheral speed and direction-of-rotation arrow |
| Soft-bond diamond blade with laser segments | EN 13236 | Hardened alpine granite, gneiss, quartzites, high-strength reinforced concrete | Cutting civil engineering elements, dressing kerbs and hard stone blocks | Inspection of bond uniformity and absence of micro-cracks at the segment root |
| Continuous rim or turbo-slotted blade | EN 13236 | Extra-thick vitrified porcelain stoneware (20 mm), wall tiles, thin slabs | Mitre cutting on a wet tile saw, chip-free adjustment cuts | Perfect flatness of the steel blade core and total absence of axial run-out |
| Diamond core bit for wet drilling | EN 13236 | Dense, heavily reinforced concrete, solid rock | Through-holes for plumbing, ventilation, and civil engineering utilities | Concentricity of threaded connection and minimum segment wall thickness |
| Solid 4-cutter carbide SDS-Plus drill bit | PGM Certification for drill bits | Reinforced concrete, sand-lime brick, hollow-core slab | Calibrated drilling for structural anchor bolts and heavy-duty fastenings | Presence of official engraved PGM mark and centring of the carbide tip |
| Solid 4-cutter carbide SDS-Max drill bit | PGM Certification for drill bits | Structural concrete, foundations, reinforced retaining walls | Large-diameter through-holes and rebar post-installation connections | Visual inspection of the extraction flute and 90-degree head geometry |
Summary of selection criteria for site supervisors
For site management and site managers, choosing between the different tools relies on an unchanging physical formula: bond hardness must be inversely proportional to the hardness of the aggregate being cut.
When cutting an extremely hard and non-abrasive material such as Swiss granite or heavily carbonated civil engineering concrete, the metal matrix holding the diamond grit must be soft (based on specific bronze or cobalt alloys). This matrix wears away through friction, releasing worn and blunted diamond grains to expose a fresh layer of sharp crystals. If the operator mistakenly uses a hard-bond blade on this material, the diamonds wear down without the matrix eroding: the blade glazes immediately. It stops cutting, overheats excessively, transfers abnormal thermal stress to the steel core, and risks sudden segment loss—a major hazard for workstation safety.
Conversely, when sawing soft yet highly abrasive materials such as road asphalt or green concrete less than 48 hours old, the cutting slurry fiercely erodes the matrix. Using a soft bond on these substrates causes premature pull-out of the diamond grains before they can complete their mechanical work. The tool wears out within minutes, wiping out the projected margin for that project phase. Specifying a hard bond (a tungsten- or nickel-loaded matrix) is therefore essential to resist the abrasive attack of silicious slurry or dust.
For structural drilling, selecting a drill bit certified under the PGM Certification for drill bits protocol is the contractor's only way to ensure drill holes meet the geometric tolerances required for approved anchors. A worn or uncertified drill bit produces an oval or tapered hole that drastically reduces the load-bearing capacity of guardrail anchorages or collective safety equipment. In accordance with the Construction Works Ordinance, such fall prevention devices must be anchored with total safety to effectively protect workers against fall hazards.
Finally, machine-tool compatibility must not be overlooked: observing the rotational speeds specified by the EN 13236 standard determines tool life and prevents failure due to mechanical fatigue. Employers thus ensure legal compliance, uncompromising worker safety at the cutting face, and strict control of tooling costs on Swiss construction sites.
Standard tooling allocation by type of intervention
Sizing the rotary diamond tooling and carbide drilling equipment directly dictates adherence to structural work and technical finishing work schedules. Inadequate allocations lead to downtime for entire crews and accelerate drive-motor breakdown through mechanical overloading. The employer ensures beforehand that assigned equipment strictly matches the mineral properties of the substrates encountered, pursuant to art. 3 OTConst, which governs the thorough planning of construction work to minimise health hazards and accident risks.
On Swiss ground, the simultaneous presence of highly abrasive alluvial aggregates, high-performance reinforced concrete, and historic masonry demands strict sector-specific kit allocation. The following assignment tables summarise equipment standards by type of operational team on construction sites across western Switzerland and the Central Plateau.
| Type of construction site | Crew composition | Diamond blade and core bit specifications | Percussion drill bit specifications | Mandatory ancillary equipment |
|---|---|---|---|---|
| Structural work and civil engineering (formwork concrete, foundation slabs, diaphragm walls) | 1 foreperson, 3 plant operators / formwork carpenters | Soft- or medium-bond blades, laser-welded segments per EN 13236, increased diamond height for heavily reinforced concrete. Castellated-segment diamond core bits for drilling through dense rebar. | Solid 4-cutter carbide drill bits with heavy-duty shank, certified under the PGM Certification for drill bits for drilling structural rebar connections. | Certified-class dust extraction shrouds, pressurised water tanks for wet cutting, enclosed cut-off saw guards complying with technical rules. |
| Finishing work and building services (plumbing and ventilation penetrations) | 2 plumbers / electricians | Thin continuous-rim turbo-slotted cut-off blades for clean cutting of mineral slabs. Dry diamond core bits with integrated axial dust extraction. | Standard-shank 4-cutter drill bits, solid carbide heads, quadruple-flute dust removal for technical plug drilling. | Power-tool-actuated industrial vacuum cleaner with automatic filter cleaning, mechanical centring devices, personal hearing protection. |
| Interior renovation in occupied premises | 2 multi-skilled tradespeople | Diamond cup wheels with abrasive segments and a hard bond adapted to mortars and levelling screeds, dust extraction cowls sealed with perimeter brushes. | Hollow extraction drill bits with 4-cutter carbide head removing dust directly from inside the drilled hole. | Mobile air scrubbers, negative-pressure dust containment sheeting, respiratory and hearing personal protective equipment. |
| Civil engineering structures and road infrastructure work | 1 site manager, 4 civil engineering workers | Large-diameter blades with very hard tungsten carbide bond for abrasive asphalt, trapezoidal segments with steel core undercut protection. | Extra-long 4-cutter drill bits with open flute geometry, reinforced carbide for drilling through thick mixed masonry. | Mobile water bowsers with delivery pump, slurry collection equipment, heavy-duty swing-radius delineation. |
Logistical organisation and consumable dispatch
Individual or crew tool allocations must be logged on an internal transfer sheet. The plant and tool manager checks that each petrol or electric cut-off saw is fitted with properly machined clamping flanges free from distortion and corrosion. The employer must appoint a competent person on the construction site to supervise compliance with operating and safety instructions, in accordance with art. 5 OTConst.
It is strictly prohibited to hand out blades designed for continuous wet cutting to operators working dry. The heat build-up would break down the bond without exposing fresh diamond grit, exposing the operator to catastrophic steel-core failure. Preventive inventory control on site requires continuous stock rotation: any tool exhibiting noticeable run-out or cracks in the steel core must be scrapped immediately without any attempt at manual repair.
Illustrative practical cases (typical scenarios on Swiss construction sites)
The data, dimensions, and costs set out below are illustrative examples designed to model the actual constraints encountered by building contractors throughout Switzerland.
Typical scenario 1: Drilling for starter bars in dense reinforced concrete (Canton of Vaud)
On an office building construction site in the canton of Vaud, a structural work crew made up of one foreperson and two masons needs to post-install 420 rebar dowels with a diameter of 16 mm into a high-performance concrete slab foundation. The concrete contains hard crushed siliceous aggregate and an especially dense top layer of welded mesh.
The initial technical choice was low-cost drill bits with two brazed cutters. Within the very first metres drilled, the bit heads struck longitudinal reinforcement bars, causing mechanical binding, torsional failure of the carbide tips, and heavily out-of-round holes. The drilled holes were no longer cylindrical, which jeopardised installation tolerances for the anchoring resin. This defect forced the firm to review its entire tool allocation to meet the obligation of supplying faultless materials and delivering work free of defects, as set forth in art. 365 CO.
Site management approved switching to solid 4-cutter carbide one-piece drill bits holding the PGM Certification for drill bits. The four symmetrical cutting edges steer the tool across the steel without drifting or jamming, pulverising rebar and surrounding concrete evenly. The drill hole diameter stays constant over the entire depth, ensuring safe injection of the chemical mortar.
The comparative financial review illustrates the sound logic of this technical decision:
- Unsuitable initial option: 18 two-cutter drill bits ruined prematurely, repeated jamming generating 34 hours of non-productive labour, representing an overall estimated outlay around 4 850 CHF excluding taxes.
- Compliant technical option: 4 PGM-certified solid 4-cutter drill bits, zero rebar jamming incidents, doubled drilling rate, representing a tooling investment around 620 CHF excluding taxes and stabilized labour at 2 100 CHF excluding taxes.
- The total cost of the compliant operation comes to an illustrative ballpark figure of 2 720 CHF excl. VAT, or 2 940,30 CHF incl. VAT at the Swiss VAT rate of 8,1%. The net overall saving for the firm reaches roughly 2 130 CHF excl. VAT compared to the non-compliant initial method.
Typical scenario 2: Cutting asphalt pavement slabs and kerb concrete (Canton of Fribourg)
As part of an urban redevelopment scheme in the canton of Fribourg, a four-person civil engineering team needs to cut longitudinal trenches across a roadway made up of 12 cm of highly abrasive asphalt overlay and a lean-mix concrete bedding base for granite kerbs.
Using an « all-round concrete » multi-purpose blade immediately caused segment glazing on the asphalt layer, as the wear matrix was too hard to clear bitumen fines, followed by violent abrasive wear on the steel core when tackling the bedding concrete. To prevent any segment rip-off at high rotational speed, the site manager applied the requirements of art. 4 OTConst by adapting the health and safety plan and the plant equipment package for the operation.
The package was split into two distinct tooling sets: a special carbide-reinforced extra-hard bond asphalt blade with protective undercut-resistant angled segments for the asphalt layer, followed by a medium-bond reinforced concrete blade fitted with laser-welded segments certified to EN 13236 to cut through the bedding concrete.
This well-planned execution scenario shows the following indicative financial figures:
- Purchase of two dedicated asphalt blades and two high-performance reinforced concrete blades: indicative cost of around 1 180 CHF excluding tax.
- Steady linear cutting speed without engine overheating, zero tool breakage over the full length of the trench.
- The total cost of the consumable package stands at an indicative amount of 1 180 CHF excl. VAT, i.e. 1 275,60 CHF incl. VAT (VAT 8,1 %). This approach prevents repeated replacements of burned blades that would have generated an extra cost of over 2 400 CHF excl. VAT in substitute tooling and earthworks delays.
Protocol for receipt, storage and commissioning inspection
Operational safety begins as soon as consumable parcels arrive at the central stores or the construction site welfare facilities. The physical inspection of wear parts must follow a rigorous procedure before any issue to production crews.
Incoming goods inspections for diamond blades and core bits
- Check permanent markings on the blade face: explicit compliance marking with European standard EN 13236, indication of maximum permitted peripheral speed, and rotation direction arrow.
- Visual inspection of the weld area: the laser weld seam between the segment and the steel core must be even, uniform, and free from porosity, cracks, or visible micro-debonding.
- Check flatness and blade tension: suspended from a finger, the blade should ring clear when tapped lightly with a non-metallic object; a dull thud signals an internal hairline crack requiring immediate scrapping.
- Check the centre bore: the arbor hole diameter must match the machine spindle precisely without play exceeding assembly tolerances; loose reducing rings are strictly prohibited on hand-held cut-off saws.
Incoming goods inspections for carbide hammer drill bits
- Check the certification mark: systematic check for the geometric hallmark issued by the PGM drill bit certification, guaranteeing drill hole tolerances for metal expansion anchors and chemical anchor studs.
- Alignment of the carbide head: the four cutters must form a symmetrical cross without any offset relative to the flute flatted lands.
- Condition of the drive shank: guide flutes and locking detents must show no burrs, deep gouges, or deformations likely to damage the hammer drill tool holder.
At workstations and along traffic routes on the construction site, physical measures must prevent falling or projecting building components from endangering personnel, as set out in art. 17 OTConst. Diamond tools must therefore be stored in vertical racks or individual padded cases, protected from moisture and hydrocarbons, to preserve the cohesion of the sintered bonding matrices.
Critical operating errors and site consequences
Field observations on construction sites show that major incidents stem from a lack of understanding of cutting mechanics or from attempts to make immediate savings on consumables.
| Observed operating error | Physical mechanism involved | Equipment and structural consequences | Health and safety impact |
|---|---|---|---|
| Using a hard bond on a very dense material (granite, quartz) | Premature polishing of diamond tips without matrix erosion (glazing). The tool rubs instead of shearing the stone. | Extreme overheating of the steel core, loss of blade tension, wander in the cut path, zero cutting feed rate. | Intense heat build-up, risk of thermal breakage of the diamond segment flying off at high kinetic speed. |
| Cutting asphalt with a standard concrete blade | Abrasive fines from bituminous sand erode the steel core body right below the segment base (undercutting). | Complete mechanical rip-off of diamond segments, warped blade, instant tool write-off. | Heavy metal fragments flying out of the guard, high-velocity material projection toward the operator. |
| Drilling through rebar with a two-cutter bit | Flute jamming caused by wedging as soon as the cutting edge bites unevenly into the reinforced concrete round rebar. | Clean head fracture flush with the shank, bit stuck inside the structure requiring costly relief core-drilling. | Violent torque reaction kickback through the operator's arms, joint trauma to wrists and shoulders. |
| Grinding using the side face of a cut-off blade | Lateral bending stresses on a thin blade designed exclusively to absorb circumferential radial forces. | Immediate structural weakening of the core steel, delamination of the segment-to-steel bond, tool failure. | Total burst of the blade rotating at thousands of revolutions per minute, fatal physical hazard. |
| Excessive rotational speed on an unsuitable machine | Exceeding the maximum specified peripheral speed in metres per second relative to the outside diameter. | Destructive vibrations, sudden loss of tension in the steel centre, instant wear of machine spindle bearings. | Centrifugal disintegration of the spinning blade, immediate life-threatening hazard in the direct workspace. |
Scrapping criteria and preventive maintenance
Monitoring wear on cutting and drilling equipment forms an integral part of operational maintenance in a modern construction firm. Plant managers and site foremen must enforce objective replacement thresholds to avoid costly breakdowns and ensure the absolute consistency of completed structures.
End-of-life indicators for a diamond blade or core bit
- Residual segment thickness: the tool must be taken out of service as soon as the diamond segment height reaches the safety wear mark of one millimetre above the steel backing core. Continuing to cut into the backing steel permanently ruins the cut and risks tearing the core plate.
- Steel undercutting or erosion: any reduction in steel core thickness beneath the laser weld line exceeding half a millimetre requires unconditional scrapping, otherwise the segment risks centrifugal ejection.
- Radial cracks: the appearance of hairline cracks running from the bottom of cooling slots toward the blade centre indicates critical fatigue from alternating thermal and mechanical stresses.
- Permanent geometric distortion: blade warping beyond guidance tolerances or noticeable blueing of the steel plate from uncontrolled overheating results in immediate loss of tool compliance.
Scrapping criteria for SDS hammer drill bits
- Wear mark vanishing from the land: PGM-certified drill bits feature a wear indicator on the carbide flank. As soon as this mark disappears, the outer diameter of the hole drilled no longer guarantees the nominal pull-out load of approved expansion anchors.
- Chipping on cutting edges: material loss on any of the four cutters disrupts the dynamic balance of drilling, causing intolerable transmission vibrations and an out-of-round hole unsuitable for structural anchoring.
- Wear on drive flutes: abnormal axial or radial play inside the machine chuck quickly damages the hammer drill tool holder and reduces the impact energy delivered to the rock.
Sound construction site management ensures that discarded tools are systematically returned to a dedicated metal recycling bin for raw material recovery, while strictly prohibiting the reuse of worn drill bits or blades at another workstation.
Free construction site calculators
Thirty-five trade calculators: site installations, waste, concrete, screeds, insulation, scaffolding. No sign-up required.
Frequently asked questions
How do you select matrix hardness to cut Valais granite without glazing?
For hard, abrasive granite, a soft bronze-based metal matrix is required. Worn diamond grits shed naturally to expose new cutting edges. A bond that is too hard causes immediate segment glazing, overheating past six hundred degrees, and a complete cutting stop. Emergency dressing on a sand-lime brick costs around 45 CHF in wasted labour time per operation. The employer applies the prevention principles of the ordinance on the prevention of occupational accidents and diseases.
What linear speed must be observed under EN 13236 for dry cutting reinforced concrete?
Standard EN 13236 recommends a maximum peripheral speed of 80 m/s on a hand-held angle grinder or 100 m/s on a stationary machine. For a 230 mm diameter blade, this corresponds to approximately 6650 rpm. Any higher speed generates excessive centrifugal stresses that risk tearing off laser-welded segments. The employer complies with the duty to safeguard personnel integrity in accordance with the general provisions of the ordinance on safety and health protection of workers in construction work relating to work equipment.
Why is PGM certification required for structural anchoring under technical approval?
The PGM drill bit certification label guarantees strict machining geometric tolerances on the carbide head diameter. A worn or non-certified drill bit produces an undersized or tapered hole that prevents proper mechanical expansion of heavy-duty anchors. This compromises the pull-out tensile capacity required by the structural engineer. Proactively replacing an SDS-Max four-cutter drill bit costs around 85 CHF, preventing defective anchor remediation where remedial core drilling costs exceed 420 CHF excluding tax.
What measures must be implemented to capture respirable silica dust during chasing?
Dry cutting masonry releases highly harmful respirable quartz. Under the ordinance on safety and health protection of workers in construction work, air quality must be ensured by extracting, filtering, or diluting pollutants, and suitable respiratory protective equipment must be worn if technical measures prove insufficient. Using a sealed dust extraction shroud connected to a certified M- or H-class dust extractor is required. The technical investment runs to around 1450 CHF to protect the respiratory system.
What mechanical hazards arise from cutting asphalt with a hard-concrete blade?
Bituminous mix is a highly abrasive material with a soft binder. If used on asphalt, a concrete blade suffers premature erosion of its steel core right beneath the segments, leading to heat buildup and undercutting. Segment detachment then becomes inevitable under tangential friction forces. Under art. 17 OTConst, measures must be taken to ensure workers are not endangered at workstations by flying debris from failing equipment.
How do you prevent violent jamming of an SDS-Max drill bit when hitting dense rebar?
Drilling through rebar requires a core bit or solid drill bit with four full-carbide cutting edges. Unlike two-cutter heads that jam between rebar rods, the symmetrical head geometry shatters the steel without sudden rotational kickback. This positive guiding prevents brutal slipping clutch engagement and reduces musculoskeletal shocks to the worker's forearms. Harmful vibrations are thus reduced in accordance with federal directives governing workplace safety and health on the construction site.
When should wet diamond core drilling be chosen over dry drilling?
Drilling with a continuous water feed is essential for diameters exceeding 82 mm in heavily reinforced concrete containing siliceous gravel. Water cools the brazed segments, prevents thermal delamination, and flushes abrasive slurry without releasing dust into the air. Art. 22 OLT 3 requires noise and vibrations to be controlled using appropriate technical measures. Wet cutting also lowers the sound level by several decibels compared to pneumatic hammering on load-bearing structures.
What contractual obligations fall on the contractor when asbestos is detected in plaster?
In accordance with art. 3 OTConst, work must be planned so that health risks are as low as possible, with the employer identifying and assessing hazards whenever asbestos is suspected. If asbestos is unexpectedly discovered during grooving or drilling, work must be stopped immediately and the site management notified. Under no circumstances should unconfined rotary grinding or drilling continue. A prior technical diagnosis avoids decontamination costs for contaminated areas exceeding 8500 CHF.
Carefully selecting diamond tooling and carbide cutting edges ensures machinery longevity, dimensional accuracy for anchors, and comprehensive protection of site crews against flying fragments and dust. To further refine your sawing and drilling procedures on construction materials, consult our specialist technical guides:
- Diamond Blade Mechanics: Why Soft Bonds Suit Swiss Granite and Hard Bonds Suit Asphalt
- Continuous Rim, Turbo Fluted or Laser-Welded Segments: Preventing Shattering and Chipping on 20 mm Porcelain Stoneware
- Solid Carbide 4-Cutter SDS-Plus and SDS-Max Drill Bits: Drilling Rebar Without Jamming and Complying with ETA Tolerances
- Diamond Blade Compatibility Matrix: Choosing Between Soft and Hard Bond Depending on the Cut Material