Skip to content
Sign in Sign up
Categories
Power tools DrillsScrewdriversGrindersSaws Measure Laser levels Protection Protective equipment Site Ladders and stepladdersHand tools
Support
Change language: French
Practical guide

Continuous Rim, Fluted Turbo, or Laser-Welded Segments: Avoiding Bursting and Chipping on 20 mm Porcelain Stoneware

Diamond blade selection for 20 mm porcelain stoneware on Swiss sites. Prevent bursting and comply with standard SIA 118 and the OTConst.

Table of contents
The 3 Major Site Risks
  1. Financial / Margin: Thermal cracking of 20 mm porcelain stoneware slabs caused by an unsuitable blade geometry. Remaking broken slabs generates direct extra costs of at least 15 % of the exterior paving package, charged to the contractor under art. 364 CO and art. 365 CO.
  2. Legal / Joint Body / SUVA: Ejection of segments at high speed or generation of respirable dust during non-compliant dry cutting. Non-compliance with personnel safety exposes site management and the employer to penalties under art. 229 CP in the event of endangerment of life or limb.
  3. Administrative / Acceptance: Visible chipping and spalling on the edges of slabs laid on pedestals or mortar, leading to refusal of acceptance of the work during inspection by the client under standard SIA 118.

Shaping and cutting 20 mm thick porcelain stoneware slabs using a petrol cut-off saw or a wet saw bench requires careful selection of the diamond rim. The extreme density of vitrified stoneware, combined with internal stresses built up during high-temperature firing, leads to instantaneous cracking or unacceptable chipping if the cutting tool is incorrectly calibrated. Choosing between a full continuous rim, a fluted turbo rim, or laser-welded segments comes down to the mechanics of the metallic bond, peripheral speed, and the cooling method used on the construction site.

In accordance with prevention directives on Swiss construction sites, controlling crystalline silica fine dust emissions and ensuring the structural stability of the blade guarantee both legal compliance and installer safety. Under art. 82 LAA, art. 33 OTConst, and art. 36 OTConst, the employer provides suitable cutting equipment and ensures dust extraction or integrated water lubrication. This technical guide details diamond tool bond engineering to prevent slab bursting and guarantee an impeccable finish in line with Swiss recognized trade practices.

Mechanical analysis of cutting rims: continuous rim, turbo, and laser segments

The mechanical behaviour of a diamond tool on 20 mm vitrified porcelain stoneware depends on its rim geometry and the hardness of its metallic matrix. When shaping exterior slabs, the friction generated by an unsuitable peripheral speed causes critical temperature spikes. A full continuous rim delivers a clean cut without micro-chipping thanks to a homogeneous distribution of synthetic diamond grit, but it requires continuous wet cooling to prevent bond glazing. Conversely, a turbo rim features helical flutes that facilitate micro-chip clearance and improve cooling during dry cuts, at the risk of inducing slight vibrations along the top edges of the material.

Laser-welded segments offer the highest mechanical resistance to segment loss under centrifugal force. This attachment method is recommended when using petrol cut-off saws or angle grinders operating at high speeds. However, the gullets between segments cause repeated impacts along the edge of thick porcelain stoneware. These repeated shocks exceed the tensile strength limit of the vitrified material, leading to internal fractures or the complete bursting of the slab. When installing exterior pavers on pedestals or mortar, professionals must select blade geometry based on the type of machinery used and the finish quality required by site management.

Cooling and crystalline silica fine dust extraction

Cutting porcelain stoneware releases extremely fine crystalline silica particles. The employer must plan site operations to limit worker exposure and maintain clean ambient air at the workstation. Using a table saw with closed-loop water delivery is the primary solution for eliminating dust emissions at the source. Where dry cutting is unavoidable on the construction site, the machine must be connected to an industrial extraction unit fitted with a hazardous substance filter, in accordance with the provisions of the Ordinance on the Safety and Health Protection of Workers in Construction Work.

If engineering and extraction measures prove insufficient to guarantee a safe atmosphere, wearing respiratory protective equipment becomes mandatory for all personnel assigned to the cutting area. The Ordinance on the Prevention of Accidents and Occupational Diseases requires the employer to supply equipment compliant with state-of-the-art standards and ensure it is actually used. Furthermore, continuous use of handheld cutting power tools generates high noise levels and hand-arm vibration. The requirements of Ordinance 3 on the Labour Act must be applied to mitigate noise at the source and safeguard worker hearing with suitable individual hearing protection.

Technical selection matrix for shaping 20 mm porcelain stoneware

Type of equipmentBlade specificationPrimary site useOperational requirementCritical inspection point
Wet table saw with water trayFull continuous rim with soft bondExposed straight cuts and mitres on 20 mm slabsContinuous pressurized water coolingAbsence of runout and water flow check
Handheld angle grinderFluted turbo rim with medium bondPerimeter adjustments and dry cut-outsConnected dust extraction deviceRegular blade dressing on abrasive dressing stone
Handheld petrol cut-off sawLaser-welded segments with hard bondRough slicing and openings in concrete and asphaltSegment attachment rated for linear speedVisual inspection for braze micro-cracks
Rail-guided sawReinforced continuous rim with silent coreXL format and high-precision bevel cutsConstant feed rate without axial pressureGuide rail alignment check
Cordless power cutterThin turbo blade with close-pitch segmentsQuick trimming on scaffolding or confined areasAdjusted protective guard and sealed housingDiamond wear and motor rotation speed

Frequent procurement mistakes and financial impacts

Misjudging the compatibility between the diamond blade bond and material hardness causes high operational costs. The most frequent mistake is using a hard-bonded blade, originally intended for asphalt or green concrete, on a vitrified porcelain stoneware slab. The metallic bond does not wear fast enough to expose fresh diamond crystals. The tool glazes, overheats, and eventually binds in the cut, snapping the slab clean through. For a medium-sized exterior hardscaping package, breakages can quickly reach 10 % of the supplies, representing a dead loss of around 1'800 CHF to 3'500 CHF in materials and non-billable labour hours.

Another classic failure involves running continuous rim blades dry on grinders turning at excessive speeds. The lack of liquid cooling induces thermal shock at the centre of the tool, ruining the steel core tension. The blade begins to warp, chipping the edges of the porcelain stoneware and ruining joint aesthetics. The contractor remedies these defects at its own expense under art. 364 CO and art. 365 CO governing execution liability. Finally, failing to inspect equipment and segment conditions prior to fitting can result in tool failure mid-rotation. In the event of serious personal injury stemming from disregard for recognized technical standards, site supervisory staff may face criminal liability under art. 229 CP.

Illustrative practical cases (typical scenarios on Swiss construction sites)

The following scenarios are illustrative examples designed to guide technical choices on site and do not represent actual construction projects.

Scenario 1: Residential patio installation in the canton of Vaud

On a construction site located in the canton of Vaud, a landscaping firm with 6 workers had to lay 220 m² of 20 mm thick porcelain stoneware slabs on pedestals. Site management demanded flawless, chip-free finishes along glass facades and around swimming pool copings. The crew initially planned to make all cuts using an angle grinder fitted with a standard dry turbo blade. After inspecting a test cut, the foreman noted an unacceptable level of micro-chipping along the visible edges.

The contractor adjusted its working method by bringing a professional water-cooled wet saw onto the construction site, fitted with a soft-bonded, full continuous rim diamond blade. Angle adjustments were kept for the angle grinder fitted with an extraction shroud. This choice maintained a steady cutting speed without tool overheating, eliminating breakages entirely and ensuring full compliance with the aesthetic criteria of the works contract.

Scenario 2: Public space refurbishment in the canton of Geneva

As part of an urban renewal project in Geneva, a civil engineering contractor with a crew of 12 workers had to cut thick stoneware slabs and reinforced concrete kerbs. To save time, an operative attempted to use a petrol cut-off saw fitted with a continuous rim blade intended for interior wall tiles. After a few minutes of dry cutting into dense material, the blade core distorted under extreme heat, producing severe runout that cracked three consecutive slabs.

The site manager halted cutting immediately to redirect tooling choices. Under art. 82 LAA, the employer reminded the team of the obligation to implement suitable prevention measures and use appropriate machinery. The warped blade was replaced with a wide-gullet, laser-welded diamond blade engineered specifically for high-speed petrol cut-off saws. Using a pressurized water tank connected to the tool provided continuous rim cooling, suppressed respirable dust, and kept workers safe on the public thoroughfare.

Free construction site calculators

Thirty-five trade calculators: site installations, waste, concrete, screeds, insulation, scaffolding. No sign-up required.

View trade calculators

Frequently asked questions

Which rim should be selected to cut 20 mm porcelain stoneware without chipping on site?

For 20 mm porcelain stoneware, use a continuous rim diamond blade with a soft bond. Wet cutting prevents diamond glazing and limits heat build-up. Under art. 82 LAA, the employer provides suitable water-suppression equipment and personal protective equipment.

Why must dry brazed segments never be used on a petrol cut-off saw?

Intense heat generated during dry cutting on a petrol cut-off saw melts the silver braze, risking segment ejection. Only laser-welded segments provide the necessary mechanical strength. Site management or the designated safety officer under art. 5 OTConst ensures strict compliance with instructions.

How does standard SIA 118 govern the cost of worn diamond blades?

Standard SIA 118 states that the contractor supplies the tools and consumable equipment required for the proper execution of the works. Wear on diamond blades for slab cutting, with an indicative value of 150 CHF, is included in the agreed unit price unless contracts specify otherwise.

What should be done if quartz dust is released during dry cutting?

Under art. 33 OTConst, ambient air at the workstation must comply with exposure limits, and hazardous substances must be vented outdoors, filtered, or diluted by ventilation. If these technical measures prove insufficient, respiratory protective devices must be donned immediately.

What is the legal liability if an unsuitable blade causes an accident?

If the shattering of an unsuitable blade endangers human life due to a lack of inspection or deliberate disregard for technical rules, art. 229 CP applies, carrying a custodial sentence or a monetary penalty. Art. 3 OPA requires employers to enforce safety rules.

Why is a fluted turbo rim recommended for reinforced concrete slabs?

The fluted turbo rim provides an optimal balance between cutting speed and edge finish. The flutes clear sawing slurry and cool the diamond blade core, preventing distortion of the steel centre. For safety, wearing a suitable hard hat under art. 6 OTConst remains mandatory.

Choosing the right design—continuous rim, turbo profile, or laser-welded segments—guarantees clean, chip-free cuts while keeping workers safe on Swiss construction sites. To deepen your technical expertise on diamond tools and consult our compatibility matrices, explore our dedicated resources:

Art Construction is an independent company: it is not affiliated with the SIA, CRB, SUVA, or KBOB. Referenced norms and standards point to publications from these bodies; only official versions are legally binding.