Table of contents
The 3 Major Site Risks
- Financial / Margin: Fire loss or rework of frost-damaged bitumen in the Pre-Alps, resulting in a direct loss of approximately 15 000 to 45 000 CHF under the Code of Obligations (CO).
- Legal / Joint Body / SUVA: Work stoppage ordered by the labour inspectorate or SUVA due to a missing hot work permit or lack of guardrails, pursuant to the construction work ordinance.
- Administrative / Handover: As-built documentation rejected or payment withheld during verification under standard SIA 118 due to missing inspection sheets for special insulation.
In the canton of Fribourg, waterproofing and special insulation (CFC 225) demand a rigorous organisation structured around directive CFST 6508. Local contractors manage the operational challenge of French-German bilingualism across construction sites in the Sense district and southern Fribourg. Safety instructions, particularly job safety sheets for operating blowtorches, using bituminous solvents, and preventing falls from flat roofs, must be clearly understood by every worker.
The contrasting climate between the Broye plain and the Pre-Alps in Gruyère requires strict planning around winter weather windows. Pursuant to art. 82 LAA, the employer implements the technical measures tailored to local conditions to prevent accidents, while art. 4 OTConst requires a written plan detailing preventive measures and first aid before work begins.
Free software, runs directly in your browser
Studio MSST: safety procedures and QR code notices
Build your MSST procedures, print workstation safety sheets and their QR codes. Everything runs locally in your browser, with no data transmitted.
Integrating CFC 225 hazards into the Fribourg MSST system
Waterproofing and special insulation grouped under CFC 225 involve critical risks: hot work using gas blowtorches with immediate fire hazards, falls from height from flat roofs, and chemical burns or intoxication from solvents, adhesives, and bituminous emulsions. Under directive CFST 6508, SME management must formalise these elements within their safety manual and operating procedures.
In the canton of Fribourg, this setup faces two major operational conditions. First, cantonal bilingualism requires that every operating instruction, internal hot work permit, and safety data sheet be drafted and posted in both French and German. Crews operating across both the Sense district and Glâne must understand emergency protocols without ambiguity. Second, Fribourg's topography creates sharp climate differences. In the lowlands, autumn humidity slows the drying of primer coats, whereas in the Pre-Alps of Gruyère, severe winter freezes substrates, preventing compliant welding of bitumen sheets or application of liquid synthetic resins.
For detailed quantity surveying and precise estimates based on standardised item catalogues, management can refer to the dedicated tools on Soumissions, as no unit price schedules are detailed here.
Matrix of priority safety procedures on roofs
The table below summarises the six core work situations to be displayed in preparation workshops and kept in Fribourg site binders:
| Work situation | Identified hazard | Organisational and technical measure | STOP point criterion |
|---|---|---|---|
| Welding bituminous membranes | Fire breakout on combustible insulation or timber parapet | Formal hot work permit, two inspected fire extinguishers within arm's reach, thermal watch two hours after extinguishing flames | No operational fire extinguisher or unprotected oxidising agents present |
| Access and movement on flat roofs during structural work | Fall from height along roof edges | Prior installation of a rigid edge guardrail or facade scaffolding compliant with the construction work ordinance | Reaching roof edges without installed and inspected collective fall protection |
| Openings for rooflights and slab penetrations | Fall through floor slab openings | Installation of rigid, bolted cover boards with clear markings or continuous edge barriers | Opening cover loose, unsecured, or unmarked |
| Application of solvent-based resins and primers | Inhalation of harmful vapours and skin toxicity | Adequate natural ventilation, mandatory use of suitable respirators and impermeable gloves | Confined space without fresh air supply or respiratory mask missing |
| Winter working conditions at high elevation (Gruyère) | Slipping on ice, adhesive freezing, and poor adhesion | Thermal monitoring of substrates, mechanical snow clearance without damaging the vapour barrier, tarping | Frozen substrate, visible frost, or temperatures below material thresholds |
| Handling heavy rolls using a hoist | Acute lumbago, load tipping over facade | Compliant rigging, inspected hoist, loads distributed across load-bearing elements per the layout plan | Ground lifting zone not cordoned off or slab overloading detected |
Organisation of the typical week: preparation, briefing and monitoring
The long-term success of an enterprise with 5 to 50 employees depends on a strict weekly routine, independent of daily urgencies. On Friday afternoon, the site manager and workshop foreman handle internal preparation: checking gas cylinders, inspecting torch burners, checking extinguisher stocks, and allocating personal protective equipment. On Monday morning on the construction site, a ten-minute bilingual briefing outlines the week's tasks, highlights fall-hazard areas, and confirms the emergency water point. Mid-week, the safety officer carries out an unannounced audit using a standardised checklist countersigned by the foreman.
To manage joint inspection reports and track handovers under standard SIA 118, the contractor relies on the features of the Portail platform.
Illustrative practical cases (typical scenarios on Swiss construction sites)
The figures below are illustrative examples intended to model the operational management of a waterproofing SME.
Standard scenario: Waterproofing build-up in the Fribourg Pre-Alps
An SME based in Romont employs 14 bilingual workers, assigning a 4-man crew to re-roof an administrative building in Bulle, Gruyère. Due to early nighttime frost and the presence of older timber parapets, the site manager rules out using open-flame blowtorches directly on the base layer. He specifies a self-adhesive bituminous membrane under upstands, combined with mechanical insulation fasteners. This operational decision prevents any risk of smouldering embers in the timber framework, keeps the project on schedule despite an additional material cost of roughly 4 200 CHF, and eliminates worker exposure to open flames in tight spaces.
Frequently asked questions
How do you manage torch fire risks on flat roofs in Fribourg?
The construction work ordinance requires emergency response planning. The contractor trains workers on hot work permits, requiring a two-hour fire watch and two inspected extinguishers costing around 350.00 CHF.
How do you incorporate bilingual Fribourg crews into safety procedures?
Directive CFST 6508 requires unambiguous communication of safety rules. The employer provides bilingual French-German visual sheets accessible via QR code on each construction site to ensure protective measures are understood.
What measures protect against toxic solvents in basements or underground car parks?
The construction work ordinance mandates mechanical ventilation and air monitoring. The contractor supplies appropriate cartridge respirators costing around 95.00 CHF per exposed employee.
How should CFC 225 schedules be adapted to severe winters in Gruyère?
The accident prevention ordinance requires work to be planned around weather conditions. The contractor anticipates frost with thermal barriers and postpones bitumen application to prevent structural defects.
Where should the safety plan required prior to waterproofing works be filed?
The construction work ordinance mandates a written safety plan before opening the site. Technical application data are stored in a digital file ready for submission to SUVA during inspections.
A rigorous MSST organisation strengthens operational safety and safeguards the profitability of Fribourg SMEs specialising in CFC 225. To further structure your company processes, explore our industry guides and tools:
- MSST System Under CFST Directive 6508: Standardising Procedures and Quality for a Building Contractor
- Studio MSST and QR procedure sheets for CFC 225
- MSST System and Organisation of a Waterproofing and Special Insulation Contractor (CFC 225) in the Canton of Neuchâtel
- MSST System and Organisation of a Special Waterproofing and Insulation Company (CFC 225) in the Canton of Jura
- MSST System and Organisation of an Exterior Rendering Contractor (CFC 226) in the Canton of Fribourg
