Key takeaways
- Time-domain reflectometry measures the exact distance to the discontinuity by calculating propagation time.
- A crushed conduit produces a characteristic impedance drop visible on the reflection trace.
- Recalibrating the nominal velocity of propagation ensures metric locating accuracy on site.
- The joint inspection record drawn up before any chasing establishes technical liabilities between trades.
Classifying crushing and measuring distance using time-domain reflectometry
On a commercial floor comprising one hundred and twenty shielded twisted-pair data links, systematic testing after pouring screed reveals fifteen non-compliant links. The cable certifier reports an impedance mismatch or massive failure in crosstalk and return loss tests, while the electrical continuity of all eight conductors sometimes remains intact. Rather than contemplating breaking out full trenches across tens of metres of fresh floor, the telematics technician uses differential time-domain reflectometry (TDR). This function injects an ultra-short electrical pulse into the pair and analyses the signals reflected by each physical fault encountered along the conduit path.
- Nominal Velocity of Propagation (NVP)
- Ratio, expressed as a percentage of the speed of light in a vacuum, at which an electrical signal travels through a given cable. This value depends on the dielectric constant of the insulation surrounding the copper conductors.
To obtain actionable spatial location beneath a mineral screed, the nominal velocity of propagation (NVP) entered into the tester must strictly match the installed cable batch. A deviation of just two per cent on an NVP value of seventy-nine per cent results in a metric offset of more than one metre over a sixty-metre link. The technician performs prior calibration on an offcut from the same batch number, cut to a known length measured with a tape. Once the parameter is validated, the instrument calculates the distance to the reflection point by multiplying the wave's round-trip time by the actual signal speed in the medium.
| Physical fault type | Characteristic impedance behaviour | Direction of reflected echo on TDR trace | Consequence on the link |
|---|---|---|---|
| Clean severed cable | Tends towards infinity (broken loop) | Positive pulse (upwards) | Totally open link, loss of continuity |
| Dead short-circuit | Drops towards zero ohms | Negative pulse (downwards) | Closed loop, network signal blocked |
| Crushing under screed | Local impedance drop (wires pushed together) | Negative dip followed by disturbed rise | Increase in Return Loss and crosstalk |
| Excessive pulling tension | Local impedance increase (stretching) | Slight, broadened positive peak | Degradation of transmission headroom |
The signature of a crushed cable is clearly distinct from that of a clean cut. When corrugated conduit is compressed by a cherry picker passing over it or the base plate of scaffolding before mortar encasement, the conductor insulation flattens without necessarily tearing. The spacing between the two wires of the pair decreases locally. This reduction in distance causes a sharp drop in characteristic impedance, falling from its nominal value of one hundred ohms to below eighty ohms. The tester screen displays a sharp negative dip whose x-axis indicates the distance to the impact point. By testing the link from both ends — first from the floor distributor, then from the floor box —, the operative crosses the two measurements to eliminate measurement tolerances and pinpoint the crushed point within a window of less than fifty centimetres.
Opening at the exact point, repairing the bundle, and drawing up the joint inspection record
Once the exact run length is transferred to the installation layout drawing, floor marking delineates a restricted investigation area. Instead of hacking out a continuous chase across the room, work is limited to a core drill hole or a rectangular window thirty centimetres wide by forty centimetres long centred on the affected conduit. Using a thermal imaging camera or pipe and cable locator helps verify that no other embedded services or underfloor heating loops run through that exact location. The opening is made using a light chipping hammer with continuous dust extraction to keep adjacent conduits intact.
- Careful cutting of the screed coverSaw the screed to a depth of two centimetres around the perimeter of the mark to prevent spalling, then clear the mortar with a cold chisel without striking the corrugated conduit directly.
- Exposing the conduit and visual diagnosisClear away rubble using an industrial vacuum cleaner. Inspect the condition of the corrugated conduit, whether split or crushed, and locate the outer jacket of the data cable pinched against the bare concrete.
- Compliant pulling or jointingIf the conduit still allows free movement, pull in a new cable using the old one. If blockage prevents pulling, fit an embedded waterproof junction box equipped with shielded connection modules certified for the required category.
- Complete recertification of the linkTerminate both ends and immediately rerun the autotest cycle on the certifier to validate all parameters: NEXT, insertion loss, propagation delay, and return loss.
Before undertaking any destructive work on the concrete structure or flowing screed, the site foreman prepares a written report supported by graphical traces from the certifier. Under art. 365 al. 3 CO, if any other circumstance arises that compromises the regular or prompt execution of the work, the contractor must notify the client, under penalty of bearing the consequences. On a Swiss construction site subject to standard SIA 118, the notice of defects or obstruction is served on the site management as soon as the fifteen degraded links are discovered. The joint breakout inspection record establishes material proof that the telecommunications conduits, installed according to accepted standards before pouring, sustained mechanical damage caused by third parties during subsequent structural work phases.
NVP calibration and differential diagnosis of the crushing signature
On a commercial construction site comprising one hundred and twenty copper links embedded under screed, discovering fifteen non-compliant runs necessitates a rigorous locating method. Breaking out one hundred and twenty linear metres of finished floor to replace all cable bundles represents an unacceptable financial loss and a major inter-trade dispute. Using time-domain reflectometry (TDR) makes it possible to pinpoint the impact point within a tolerance of under fifty centimetres, provided the certification tester calibration is fully mastered.
Measuring the distance to the defect depends directly on the nominal velocity of propagation (NVP). A generic data sheet value, often set between 76% and 79% for Category 7 S/FTP cable, exhibits a manufacturing variance of approximately 2% from one batch to another. Over an actual length of sixty metres, this inaccuracy shifts the diagnosis by more than one metre twenty. Before drawing any conclusions, the telematics technician measures the exact NVP on a reference sample of at least twenty metres taken from the same drum, or on an adjacent healthy link with an identical run length.
| Damage type | TDR impedance trace | Affected parameter | Consequence under screed |
|---|---|---|---|
| Direct conduit crushing | Pronounced capacitive dip (Z < 85 Ω) | Return Loss and NEXT | Crushed sheath, conductors pushed together without breaking |
| Drilling with clean severance | Open inductive peak (Z > 150 Ω) | Continuity / Wiremap | Conductors cut by drilling from false floor below |
| Cement laitance penetration | Damped, broadened ripple | Attenuation / RL | Punctured sheath, moisture ingress degrading dielectric |
| Dead short-circuit between pairs | Vertical drop towards zero ohms | Continuity / Resistance | Screw or nail penetrating pliable KRFWG conduit |
The signature of crushing under screed differs markedly from a severed cable. When pliable corrugated conduit is rolled flat beneath a forklift or heavy load prior to pouring, the thermoplastic insulation of the conductors is compressed. This crushing forces the conductors of the pair closer together locally or reduces the distance between the pair and the overall aluminium foil shield. This causes a sudden surge in capacitance per unit length and a local drop in characteristic impedance below the contractual threshold of one hundred ohms. Some of the signal energy is reflected back towards the transmitter with negative polarity, resulting in a sharp drop in Return Loss margin at the metre mark displayed by the instrument.
Prior joint inspection record and targeted breakout procedure
Intervention on freshly poured screed must never begin without a joint inspection record drawn up with the site management and the contractor responsible for the structural work or screed. Under general rules of the Code of Obligations (CO) governing contracts for work and services, the contractor notifies the facts compromising the proper execution of the works to release itself from liability for any resulting delays. The technical file submitted on the table includes the penetration and sleeve layout with conduit routing, the raw time-stamped TDR trace, the metric measurement taken from the IT distribution board, and the estimated position on the drawings.
- Transferring metric data to as-built drawings and bare floorRun the survey tape along the actual route recorded when laying the conduits on the concrete slab, taking into account vertical drops in walls and offsets around building services shafts.
- Disc cutter and surgical chasingForm a rectangular chase measuring forty centimetres by twenty using a diamond floor saw fitted with industrial dust extraction. Stop cutting two centimetres above the theoretical level of the conduit and complete exposure using a hand cold chisel.
- Visual inspection and clearing the conduitExpose the pliable KRFWG conduit. Inspect for mechanical flattening or perforation of the conduit, then slit the plastic sheath carefully without damaging the outer jacket of the network cables.
- Restoring continuity or repulling the sectionIf the conduit is not filled with cement slurry, pull in a new continuous link from the opening point. If pulling is jammed, install a Class EA shielded junction box embedded in a waterproof floor box with 360-degree shield bonding.
Remediation using a Category 6A shielded coupler is acceptable only if the mechanical environment permits and the client's specifications allow an intermediate joint. Each conductor is terminated onto an insulation displacement contact (IDC) module adhering to the maximum untwist length of thirteen millimetres. Once the joint is sealed, a complete new Class EA certification test is performed in accordance with SIA 118 before making good with non-shrink mortar. This second test report is appended to the punch list sign-off record, ensuring long-term network reliability without damaging adjacent finishes.
Dispute, irreparable cable, and major remediation protocol
When the reflectometer locates a clean break under anhydrite screed with absolute impossibility of repulling or pushing conductors through, local repair reaches its limits. If the site management refuses targeted breakout using a light pneumatic chisel for fear of damaging underfloor heating or acoustic insulation, the original route becomes unusable. The network contractor then applies art. 365 al. 3 CO by notifying the client that this circumstance compromises the regular execution of the telecommunications installation.
The initial joint inspection record, supported by time-domain reflectometry (TDR) traces and return loss (RL) measurements for each pair, forms the primary technical piece of evidence. This document discharges the telematics technician from liability for mechanical damage caused by structural work or screed trades. If agreement on exposing the pinched point cannot be reached, three rerouting alternatives are available to restore Class E or Ea links without extensive breaking out of finished flooring:
- Rerouting via the ceiling void on the floor below: localised core drilling at the base of the drywall partition and rising in rigid halogen-free conduit.
- Diversion via multi-compartment perimeter skirting trunking, connecting RJ45 outlets from the rear of existing flush-mounted boxes.
- Pulling a cable with a smaller outer diameter, subject to strict adherence to bending radii and compliance with transmission standards.
Any diversion route alters the permanent link length. Before closing temporary conduits and trunking, run a full autotest cycle on the certifier to validate propagation delay, insertion loss, and NEXT across the entire reassigned link.
Frequently asked questions
How should one respond if the certifier indicates two distant defects on the same link?
Time-domain reflectometry frequently masks faults located downstream of a clean cut or severe short circuit. You must connect the certifier to the other end of the link, at the terminal outlet side. This gives you the exact distance to the second crushed point from the opposite end. Cross-referencing both measurements avoids unnecessary screed breakout along the entire intervening run between two conduits deformed by site plant.
Can a Category 6A joint be embedded directly in screed after breakout?
This practice is prohibited under Swiss accepted standards. No junction box or shielded coupler may be cast directly into mortar without permanent accessibility. If the link cannot be repulled in one piece, install a flush-mounted pull box with a removable cover, or repull the entire F/UTP cable from the floor distributor to maintain shield integrity.
What distance error tolerance should be applied to under-slab TDR measurements?
The typical uncertainty of a copper certifier ranges from one to two per cent of the total measured length, provided the nominal velocity of propagation (NVP) was calibrated beforehand on an identical cable offcut. On a fifty-metre link, the theoretical discrepancy reaches fifty centimetres. The investigation area on the floor must therefore span a window of at least one metre along the corrugated conduit.
Who instructs the concrete sawing contractor to expose the crushed bundle?
The formal decision rests with the site management following receipt of the joint measurement record. The telematics technician provides the floor markings derived from the reflectometer and the cabling drawings. Breakout is assigned to the bricklayer or screed layer to safeguard warranties on waterproofing, acoustic insulation, and underfloor heating pipes embedded in the slab.
Texts and standards cited
- CO art. 365materials and ground: the contractor notifies the client if any circumstance compromises regular execution of the work (al. 3)
- CO art. 367inspection of the work and examination by experts at the request of either party (al. 2)
