Key takeaways
- The KNX bus uses the red pair for the positive pole and the black pair for earth.
- The distance between the power supply and a device must never exceed three hundred and fifty metres of cable.
- The cumulative length of all branches of a physical segment is strictly limited to one thousand metres.
- The screening foil and its drain wire must never be connected to earth.
Topology, limit distances and polarity marking on the control pair
The KNX system's TP1 twisted-pair medium allows great laying flexibility by permitting line, star or tree topologies. However, this technical flexibility conceals rigid physical constraints that the telematics technician must respect, or risk collapsing communication across the entire segment. A home automation installation tolerates local impedance drifts, but it cuts out immediately as soon as a polarity error is introduced at a device terminal block.
- KNX TP1 bus
- Home automation communication system operating on a screened twisted pair carrying simultaneously a nominal thirty-volt direct-current supply voltage and data telegrams modulated in baseband.
The standard KNX cable, recognisable by its green halogen-free outer sheath for commercial or residential buildings, contains four solid conductors with a cross-section of zero point eight millimetres. The main transmission pair uses the red conductor for the positive potential and the black conductor for the negative potential or zero volts. The second pair, consisting of a white conductor and a yellow conductor, serves as a spare for an auxiliary low-voltage power supply or for specific applications validated by the manufacturer. Under no circumstances must these two pairs be mixed or interconnected when connecting to the standardised plug-in bus micro-terminals.
| Physical quantity | Maximum value | Direct consequence if exceeded |
|---|---|---|
| Total cable length per line | 1000 m | Critical signal attenuation and loss of frames |
| Distance between power supply and device | 350 m | DC voltage drop below the 21 V threshold |
| Distance between any two devices | 700 m | Telegram collision due to propagation delay |
| Maximum number of power supplies per segment | 2 units | Risk of overcurrent or destruction of power supply stages |
On the construction site, the temptation to close a loop by connecting the end of a line back to the distribution board to secure the power supply is common among installers unfamiliar with the protocol. This closed-loop topology is prohibited in KNX: it generates destructive wave reflections that corrupt the transmission of differential frames. A line is always deployed in an open tree structure.
Electrostatic screening treatment and line diagnostics before power-up
Certified KNX bus cable features an aluminium screen wrapped over plastic tape, supplemented by a tinned copper continuity conductor, commonly referred to as a drain wire. Managing this screening follows strict rules that differ completely from RJ45 screened twisted-pair IT links or the earthing links of heavy-current installations. The KNX system operates on the principle of safety extra-low voltage not connected to earth, known as SELV galvanic isolation.
The sole purpose of the KNX cable screening is to protect telegrams from electrostatic interference radiated by adjacent cable bundles in service risers or cable trays. The screen and its drain wire must imperatively maintain their continuity from one junction box to another by splicing them or connecting them to an insulated dummy terminal. Conversely, the screening must never be connected to protective earth, either in the distribution board or on device chassis. Earthing the drain wire turns the screen into a receiver of transient earth loops, generating interference far more destructive to electronic components than ambient interference.
- Continuity and insulation test with power offBefore installing any devices or powering up the power supply module, measure the insulation between the red conductor and the black conductor using an ohmmeter. The resistance must display an infinite value. Repeat the measurement between each active conductor and the floating screen drain wire.
- Insulation of spare conductorsFold back the white and yellow conductors along the sheath or insert them into the dummy pins provided on the back of the bus micro-terminals. Never cut these wires flush with the sheath, in order to retain a spare length available for future diagnostics.
- Voltage test under line powerSwitch on the KNX power supply at the distribution board. Measure the DC voltage on the test terminals of the power supply, then record the value at the ends of each branch. The voltage must be between 28 and 31 volts DC. A voltage of zero or close to zero indicates a short circuit or a device diode short-circuited following a crossed polarity.
- Verification of voltage drops under loadMeasure the voltage at the physically furthest device. The reading must never drop below the minimum threshold of 21 volts DC when the devices on the line send signals or illuminate their status indicators.
Hunting down polarity reversals and creeping faults at the end of the line
The KNX standard tolerates a wide variety of topologies: tree, star or linear bus coexist freely on the same control segment, without end-of-line terminating resistors. On building construction sites in French-speaking Switzerland, network electricians and telematics technicians take full advantage of this flexibility when laying conduits or routing through suspended ceilings. However, this leniency stops dead when it comes to polarity. A reversal between the red conductor (Bus +) and the black conductor (Bus -), even isolated on a single push-button or sensor at the end of the line, triggers no protective trip and causes no heat build-up. The anomaly remains completely silent during structural work, only manifesting itself as a blocking issue during commissioning with ETS software.
Functionally, the transceivers built into KNX devices include a bridge rectifier or a protective diode. A reversed connection at the network end short-circuits the signal or clips the communication waveform. Bus behaviour becomes erratic: some equipment stops sending acknowledgements, the frame repetition rate saturates bandwidth, and properly wired modules fail. To eliminate this risk, polarity is checked right from connection. Before plugging the standardised connector into a device, the installer measures the DC voltage with a multimeter: the open-circuit value must reach between 29 V and 31 V DC. A negative voltage immediately signals a reversal, whereas a value below 21 V DC under load reveals an unacceptable voltage drop.
Electrostatic screening treatment and metric limits of a segment
Certified KNX cable — identifiable by its characteristic green sheath — comprises two 0.8 mm diameter twisted pairs and an aluminium screen backed by a tinned drain wire. This screening protects signals against electromagnetic radiation from adjacent power circuits in cable trays. To be effective without injecting noise, the screen must be implemented rigorously: it must not form any closed earth loops capable of picking up inductive currents.
In junction boxes and distribution boards, screen continuity is maintained without interruption by connecting the drain wires to an independent terminal, insulated from any metallic earth. The foil is cut flush with the sheath and the drain wire is covered with an insulating sleeve. At the ends of the line, the screening and the second spare pair (white and yellow wires) are cut, insulated and folded back into the conduit without connection to earth. Where functional earthing of the screen is required, it is carried out at a single point, directly at the control panel near the power supply, which prevents any stray currents from circulating through the screening.
| Line parameter | Limit value | Consequence of exceeding limit | On-site check |
|---|---|---|---|
| Total cumulative length | 1000 m per segment | Critical signal attenuation | Sum of lengths on as-built drawing |
| Power supply to device distance | 700 m maximum | Voltage below 21 V DC threshold | DC voltage measurement at furthest point |
| Distance between devices | 350 m maximum | CSMA/CA collision avoidance failure | Verification of physical cable routes |
| Screen earthing | 1 single point at distribution board | Earth loop and spurious signals | Screen insulation test at ends |
| Spare pair (white/yellow) | Insulated, not connected | Increased parasitic capacitance on the bus | Visual inspection of capping in boxes |
These maximum distances ensure that the round-trip propagation time of telegrams remains compatible with the CSMA/CA arbitration mechanism of the KNX protocol clocked at 9600 baud. If the physical distance between two devices exceeds 350 m, two transmitters can begin transmitting simultaneously without detecting the collision in time, which irreparably corrupts the exchanged frames. Before locking off the installation and handing over the wiring test reports to site management, the installer checks for the total absence of short circuits between the active conductors, the auxiliary pair and the screening foil using an insulation tester at a test voltage of 250 V DC. This metric and electrical rigour ensures a sound communication infrastructure prior to any logical integration.
Methodical troubleshooting protocol and resolving wiring faults
When the KNX power supply trips into short-circuit protection or the IP gateway refuses to communicate with devices, any attempt at individual addressing using ETS software becomes pointless. The technician applies a diagnostic method by methodically splitting the segment. The first step consists of physically disconnecting the line from the output terminal block of the bus power supply to measure the open-circuit voltage at the device terminals. If the source correctly delivers its 29 to 30 V DC, the problem lies on the field link.
- Isolation by half-splittingOpen the standardised red and black branch connectors located at the physical midpoint of the line. Connect the first half-section to the power supply and check that the DC voltage stabilises using a multimeter. Repeat the operation through successive subdivisions until the faulty branch is located.
- Tracking down polarity reversalOn the offending branch, check the bus polarity on each device at the end of the line. A negative voltage displayed on the multimeter immediately indicates a reversal of the red and black conductors at an upstream terminal block. This swap blocks the transmitting stage of the electronic components located downstream without systematically tripping a thermal fuse.
- Screen insulation testingMeasure the insulation resistance between the aluminium foil drain wire and the active control conductors. Managing the screening requires that it remains continuous from one end of the link to the other while remaining strictly insulated from building earth and metallic masses in order to prevent stray circulating currents.
- Audit of actual lengthsRecord the actual run length: the maximum line length must never exceed 1000 m per power supply segment, with a maximum distance of 350 m between two devices and 700 m between a device and the power supply. Beyond this, attenuation of the KNX signal corrupts telegrams.
In the event of a defect attributable to faulty pulling or crossed pairs in an inaccessible junction box, art. 364 CO reiterates the contractor's liability for the diligent execution of the work entrusted. The telematics technician logs the resistance values and measured voltages on his test report before proceeding to repair the connection or repull the certified green cable inside KRFWG conduit.
Frequently asked questions
How can a KNX bus polarity reversal be detected without dismantling all devices?
The fastest method relies on measuring DC voltage at the terminals of accessible devices using a digital multimeter. Correct polarity indicates approximately 29 V positive between the red conductor and the black wire. If the voltmeter displays a negative value, polarity is crossed on that section. Using line couplers or power supplies with an overload LED also helps identify an abnormal voltage drop.
Why must the KNX screen drain wire never be connected to PE earth?
The KNX bus operates on the principle of an unearthed safety extra-low voltage. Connecting the screening foil or its drain wire to earth creates an earth loop through which stray currents from the mains network infiltrate. This phenomenon generates electromagnetic interference on the control pair, distorts digital telegrams and causes sporadic communication losses between devices.
What should be done when the maximum line length exceeds 1000 metres on a construction site?
When the cumulative cable length of a section exceeds the 1000 m threshold, the line must imperatively be divided using a line repeater or a certified KNX coupler. This device regenerates the control signal and galvanically isolates the sections. Each sub-segment then requires its own bus power supply sized according to the number of connected actuators and sensors, respecting the limit of 64 devices per physical segment.
What is the consequence of a distance of more than 350 metres between two KNX devices?
The timing synchronisation of KNX telegrams relies on a propagation delay calibrated for a precise line impedance. Exceeding a 350 m spacing between two devices creates a risk of frame collisions during simultaneous transmissions: the priority arbitration mechanism on the bus no longer operates deterministically. Corrupted frames then cause unnecessary retries, line saturation and erratic response times.
Texts and standards cited
- CO art. 364contractor's obligations: liability subject to the same rules as that of an employee; he carries out the work in person or under his personal direction; unless agreed otherwise by contract or trade custom, he procures at his own expense the necessary means, plant and tools.
