Key takeaways
- Single or stepladders serve only as occasional access or for interventions of very short duration.
- Installing cable trays requires the use of a mobile platform fitted with full edge protection.
- Locking the wheels and adjusting outriggers guarantee stability before stepping onto the decking.
- The floor area beneath the plenum must be cordoned off to protect other trades.
Abandoning stepladders for continuous work in plenums
Pulling twisted-pair cables, securing perforated sheet-metal cable trays or installing KNX bus couplers under slabs requires prolonged postures with raised arms. On a stepladder or double-sided ladder, the technician constantly compensates for imbalances caused by the pulling force of cable bundles or hammer drilling. This structural instability turns a repetitive two-hour task into critical exposure to falls from height. In Swiss construction site practice, ladders are no longer an acceptable workstation as soon as the operative must exert lateral force or handle loads of significant weight.
Low-height mobile scaffolding and mobile platforms offer a rigid deck allowing safe placement of the toolbox, M6 fasteners, wire cutters and cable ties. The flat working surface eliminates foot and muscle fatigue associated with narrow rungs. Above all, it allows the installer to work inside a space enclosed by collective protection, without risking a tip-over if a cable snags in a bend or a drill slips while overhead drilling into the ceiling.
| Telecom operation | Task duration | Required equipment | Deciding criterion |
|---|---|---|---|
| Occasional identification or testing of RJ45 connector | Less than 10 minutes | Secure stepladder with non-slip feet | No lateral force exerted |
| Fastening threaded rods and wall brackets | Continuous work (> 30 min) | Mobile podium steps (PIR) | Drilling and tightening under slab |
| Installing metal cable trays | Half-day or full day | Plenum mobile scaffolding | Load handling and backwards reach |
| Pulling fibre optic links or KNX bus | Continuous over long distance | Mobile scaffolding or MEWP | Repetitive pulling forces |
Deploying the mobile platform and locking the drop zone
Compliant installation of a mobile platform requires strict attention to horizontality and levelling. Before commencing work beneath false ceiling hangers, the operative must engage the wheel locks on all four swivel castors to eliminate any slippage. Where the equipment features adjustable outriggers, these must be extended to bear firmly on the foundation slab or raw screed. Pursuant to art. 22 OTConst, peripheral guard rails must have a top rail with its upper edge at least 100 cm above the working surface, supplemented by an intermediate rail and a toeboard at least 15 cm high.
Handling 3-metre cable ladder lengths, suspension rods and power tools creates an ongoing hazard for personnel circulating below. In accordance with art. 17 OTConst, measures must be taken at workstations and passageways to ensure workers are not endangered by falling objects or materials. In low-voltage applications, this requires pairing the platform toeboard with strict ground-level organisation.
- Ground perimeter demarcationMark out an exclusion corridor beneath the cable tray route using two-tone chains or lightweight barriers to bar access to other trades.
- Tethering power toolsFit impact wrenches, rotary hammers and crimping pliers with lanyards attached to the platform structure or the tool belt.
- Checks before moving equipmentClear the work deck of splice plates, nuts and metal offcuts before releasing the brakes to move to the next bay.
Residual ladder tolerance and installation non-compliances
Installing cable trays in plenums requires continuous operations needing full use of both hands: chalk line marking, laser alignment, hammer drilling concrete slabs with an SDS drill, installing metal drop-in anchors, fitting threaded rods and splicing tray sections. Performing these tasks from a single ladder or double-sided stepladder places the telematics technician in a prolonged, precarious balance. Upward pressing force combined with the reaction torque of a drill bit jamming in rebar inevitably causes a loss of footing. Portable ladders remain a means of access or a station for very short, occasional interventions with no lateral or vertical mechanical force. As soon as the task exceeds a few minutes or requires both arms raised, using secure equipment with a platform and guard rails becomes indispensable to prevent falls from height.
| Means of access | Permissible telematics tasks | Strictly prohibited operations | Postural safety level |
|---|---|---|---|
| Portable ladder or stepladder | Occasional access, visual inspection of a junction box, reading a cable label number | Slab drilling, cutting cable trays, pulling multi-cable runs | Low: constant obligation to maintain body contact, no guard rails |
| Mobile podium step (PIRL) | Repetitive fastening of threaded rods, assembling cable trays, terminating RJ45 connectors | Moving the platform with an installer on board, overloading by storing heavy materials | High: stable working deck, peripheral guard rail with toeboards, braked wheels |
| Low-height mobile scaffolding | Installing heavy industrial cable tray runs, grouped pulling of multiple network cables | Repositioning without unlocking wheels or with outriggers deployed asymmetrically | Very high: wide working area, load capacity for complete toolkit and sections |
Risk of falling tools and securing the ground footprint
According to art. 17 OTConst, measures must be taken at workstations and passageways to ensure workers are not endangered by falling objects or materials. In technical plenums, telematics technicians handle heavy, dense hardware: drop-in anchors, nuts, cut threaded rods and crimping tools. A dropped tool from a height of three metres can cause severe injuries to anyone walking beneath the workstation. Furthermore, OTConst mandates the wearing of safety helmets for all work where workers may be endangered by falling objects or materials. Helmet wearing applies to the operative and anyone circulating within the zone of influence of overhead ceiling works.
- Rigid barriers or barrier tape over a minimum radius of two metres beneath the path of travel of the mobile platform to bar access during overhead ceiling fixings.
- Systematic tethering of hammer drills and cable cutters using elastic lanyards attached to harnesses or anchor points provided on the platform guard rails.
- Using storage bins suspended from the inner guard rail to hold metal fixings, ruling out any loose screws or pliers lying on the walking deck.
- Direct disposal of cut threaded rods and wire-mesh tray offcuts into sorting drums, without leaving them around the operative's feet.
Two-person team organisation is the most effective approach to ensure both safety and installation speed. While the first installer adjusts cable tray levels and bolts brackets from the MEWP or mobile platform, the second remains on the ground to supply prepared sections and monitor the exclusion perimeter. This division of tasks avoids exhausting vertical climbing and prevents third parties from entering beneath the overhead work area. In practice, the team coordinates progress with ventilation duct fitters to avoid overlapping scaffolding footprints in congested corridors.
On-site arbitration and managing non-compliant overhead slab work
On commercial construction sites in French-speaking Switzerland, pulling twisted-pair cables or fixing cable trays in plenums too often drifts into continuous stepladder use to save supposed minutes. When a network installer works with both arms raised to drill into a concrete ceiling, balance is threatened with every kickback of the hammer drill. Under LAA, the employer must take all occupational safety measures that experience has shown to be necessary, that are technically feasible and that are adapted to the prevailing conditions. As soon as a static installation task exceeds a few minutes, the site foreman suspends the operation to bring in a lightweight mobile podium step fitted with guard rails and toeboards.
- Stopping drilling or pulling operationsThe site foreman stops the operative as soon as a ladder is observed being used as a continuous workstation. Power tools are set down on the floor.
- Securing the impact zoneIn application of art. 17 OTConst, measures must be taken to ensure workers at workstations and passageways are not endangered by falling objects. The perimeter beneath the false ceiling is cordoned off using rigid barriers or light fencing.
- Replacing equipmentCommissioning a mobile platform adjusted to the clear height of the plenum, checking wheel brakes and attaching tool lanyards to every hand tool.
If materials actually fall, even without injuries, a formal damage report is drawn up with site management. Checks are made to ensure no damage was caused to third-party services already installed below, such as plastic conduits or fluid pipework. Any mobile scaffolding that is damaged or struck by plant must be withdrawn from the installation area until recertified by its supplier.
Frequently asked questions
Can a single ladder be used to install a section of cable tray in a plenum?
No. Single ladders are reserved for temporary access from one level to another or for occasional tasks of very short duration requiring no lateral force. Sawing, hammer drilling and fixing cable tray brackets require both hands and exert horizontal forces incompatible with ladder stability. A platform with full guard rails remains mandatory.
How should the safety perimeter beneath the plenum be set out for other trades?
Mark out an exclusion zone on the ground with a radius equal to one-third of the ceiling height, plus one metre to cover bounces. Use small chains or lightweight barriers with signage indicating overhead cabling work. Bar dryliners and painters from passing beneath the platform until slab fixings and channel installations are completed.
Must network electricians systematically tether their tools to the platform?
Yes, securing pliers, ratchets, screwdrivers and hammer drills with wrist straps or elastic lanyards is essential when working above circulation routes. Even from two metres up, a dropped two-kilogram drill-driver can inflict serious injuries on a worker walking down a corridor. Guard rails must also include a bottom toeboard to retain fixings and wall plugs.
What should be done if the ceiling void is too congested to deploy outriggers?
When plenums are packed with large ventilation ducts or heating pipework that blocks the platform footprint, refuse to work in precarious balance. Request site reorganisation from site management. Installing low-voltage containment must be scheduled before spaces are blocked off by bulky ventilation services, or carried out using narrow-aisle MEWPs.
Texts and standards cited
- LAAGeneral prevention rules: To prevent occupational accidents and diseases, the employer shall take all measures shown by experience to be necessary, technically feasible, and adapted to the given conditions; workers shall assist the employer (notably by using personal protective equipment).
- OTConst art. 17Protection against structural collapse or falling objects and materials: At workstations and passageways, measures must be taken to ensure that workers are not endangered.
