Skip to content
Website
🧱 CFC 226Section 1 of 610 chapters

Substrate, slope, vapour barrier, and insulation: the standard

Intended for team leaders, site foremen, and site managers, this section compiles the technical requirements governing the build-up underlying the waterproofing membrane on flat roofs, terraces, and inverted roofs. From the formal acceptance of a concrete slab or steel deck to the thermal and mechanical anchoring of insulation boards, it defines methods compliant with standards SIA 271 and SIA 180 to prevent any premature failure.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

norme SIA 271

1.5%

Recommended minimum slope towards rainwater outlets to prevent persistent ponding

norme SIA 271

120 mm

Minimum waterproof upstand of the vapour barrier above the top surface of the thermal insulation at penetrations

norme SIA 271

4%

Maximum permissible water content in a concrete substrate prior to direct application of a primer bonding bitumen

OTConst art. 41

2 m

Threshold requiring protective measures against falls at the roof edge

Technical scope and operational boundaries

The area of competence addressed here covers all underlying layers of the waterproofing build-up pertaining to the waterproofer's trade (CFC 226). It structures the decisive stages performed before or during the application of the waterproofing membrane, from the mechanical and geometric assessment of the bare substrate to the thermal and hygrometric protection of the structure.

  • Formal acceptance of load-bearing substrates made of reinforced concrete, timber decks, or profiled metal sheets according to the acceptability rules of standard SIA 271.
  • Verification of lines of slope, control of hollows, angle fillets, and rigorous layout of overflow spouts and valley gutters.
  • Selection, continuous bonding, and upstands for air- and vapour-tightness dictated by the requirements of standard SIA 180.
  • Compressive sizing, mechanical fastening, or cold and hot bonding of thermal insulation boards under conventional waterproofing and inverted roofs.
  • Temporary water-shedding provisions and chemical separation layers essential for preserving the integrity of the build-up during construction works on the construction site.

For the operative, the compliance of the waterproofing depends directly on the quality of the substrate deck. Installing insulation without prior validation of surface moisture or failing to bridge an expansion joint across the vapour barrier exposes the waterproofer to severe claims regarding water ingress and interstitial condensation.

Deployment method and construction site scheduling logic

The sequence of the ten chapters follows the build-up layers and the practical execution requirements encountered by installation teams on the construction site chronologically. This methodical approach enables compliance checks to be anticipated before any irreversible stacking of materials.

  1. 1. Foundation inspection and drainage geometryChapters G1-01 and G1-02 address dryness, surface cohesion of the concrete, and compliance with the minimum effective slope. An insufficient slope promotes standing water and accelerates biological fouling of the membrane.
  2. 2. Hygrometric barrier and thermal envelopeGuides G1-03 and G1-04 define the seamless continuity of the vapour barrier at the base of upstands as well as the compressive strength calculation for the insulation (EPS, PIR, mineral wool, cellular glass) according to the superimposed loads from gravel, paving slabs on pedestals, or green roof finishes.
  3. 3. Wind-load resistance and structural particularitiesChapters G1-05 to G1-07 address wind uplift anchoring in perimeter zones, permeability rules for inverted roofs, and allowable spans on profiled metal sheeting without risk of punching shear.
  4. 4. Refurbishment diagnostics and construction site protectionChapters G1-08 to G1-10 detail the identification of entrapped water by core sampling on existing roofs, separating membranes preventing plasticiser migration, and temporary tie-in measures during unexpected stoppages caused by weather.

Organisation on the slab requires strict planning of light plant movements and storage to avoid crushing the rebated edges of the insulation boards. Edge-protection measures against falls from height must remain operational from the very first perimeter upstands in accordance with the construction works ordinance.

📘 Chapters in this section 10

Substrate, slope, vapour barrier and thermal insulation

Substrate Acceptance Before Waterproofing: Evenness, Dryness, and Cleanliness

Avoid membrane debonding by checking the dryness and surface cohesion of the concrete substrate.

Substrate, slope, vapour barrier and thermal insulation

Flat roof slope: practical minimum, backfalls and residual ponding

Control effective falls and eliminate counter-slopes to prevent detrimental standing water.

Substrate, slope, vapour barrier and thermal insulation

Vapour barrier on flat roofs: continuity, upstands and penetration junctions

Execute your vapour barrier upstands correctly and neutralise water vapour diffusion bridges.

Substrate, slope, vapour barrier and thermal insulation

Flat roof insulation: compressive strength by intended use

Select the insulation compressive class matched to the loads of terrace and green roof build-ups.

Substrate, slope, vapour barrier and thermal insulation

Mechanical fastening: fastener density, perimeter and corner zones

Calculate the mechanical fastener layout density to resist wind uplift forces.

Substrate, slope, vapour barrier and thermal insulation

Inverted roof: insulation above the waterproofing, and its requirements

Apply specific drainage layer and ballast rules for successful inverted roof installations.

Substrate, slope, vapour barrier and thermal insulation

Profiled steel sheet substrate: rib direction, span and insulation fixing

Secure insulation laying on profiled metal sheets by adhering to the prescribed span directions.

Substrate, slope, vapour barrier and thermal insulation

Renovating a flat roof: test cuts, trapped moisture and removal decisions

Identify entrapped water through core sampling before deciding on an overlay or full tear-off.

Substrate, slope, vapour barrier and thermal insulation

Separation layers: chemical incompatibilities between membrane and substrate

Prevent irreversible chemical deterioration by installing a suitable separation fleece.

Substrate, slope, vapour barrier and thermal insulation

Temporary waterproofing: protecting the construction site between working days

Implement watertight temporary tie-ins to secure the construction site against bad weather.