Skip to content
Website
🧱 CFC 282Adhesives, back-buttering and large formatsChapter 1 of 10 in the section

Reading an adhesive class: adhesion, extended open time, deformability and use

On a construction site in Romandy, choosing a tile adhesive is not just about grabbing a standard bag. The standardised letters and numbers determine mechanical strength against tensile loads, the time available to adjust a tile, and the capacity to absorb substrate movements. This chapter teaches you how to read these codes to ensure secure installation in accordance with the SIA 248 standard.

Key takeaways

  • Class C1 offers minimum adhesion, whereas class C2 doubles the required resistance values.
  • The letter E extends the open time to thirty minutes, preventing premature skinning under draughts.
  • The S1 index guarantees a deformation of two and a half millimetres, absorbing thermal expansion on underfloor heating.
  • Class S2 absorbs five millimetres of deflection, which is essential for large formats in exposed outdoor environments.

Deciphering the designation C1 or C2 and the contribution of technical options T, E and F

The marking of a tile adhesive complies with strict direct tensile adhesion tests. A mortar classified as C1 guarantees an initial adhesion strength of at least half a newton per square millimetre. This base value is sufficient for small ceramic elements installed indoors on a stable, dry substrate, such as a conventional cement render without thermal stress. Conversely, as soon as the structure is subjected to permanent moisture in a walk-in shower or thermal variations in a heavily glazed room, the SIA 248 standard requires improved adhesion of class C2. This binder achieves one newton per square millimetre in all test configurations, particularly after immersion in water, after thermal ageing, or after repeated freeze-thaw cycles.

Beyond pure pull-off strength, the supplementary letters indicate how the product behaves during application on the screed or wall:

  • Letter E (extended open time): extends the allowable time between spreading the notched mortar and placing the tile. This time contractually increases from twenty to thirty minutes without a drop in adhesion. This is a major advantage for the tiler working in hot weather, in the presence of draughts on open floors, or when bonding bulky slabs that require meticulous adjustments.
  • Letter T (reduced slip): limits tile sagging under its own weight during wall application to less than half a millimetre. This choice eliminates systematic bottom wedging and allows top-to-bottom installation.
  • Letter F (fast-setting): accelerates cement crystal formation with measurable adhesion after just six hours. This product is essential for the refurbishment of commercial surfaces that must be reopened to foot traffic the following morning or for grouting on the same day.

Mastering S1 or S2 deformability in the face of differential substrate movements

Masonry substrates are never inert: residual concrete shrinkage, expansion under underfloor heating pipes, deflections of load-bearing elements, or thermal shocks on facades subject the adhesive to pure shear. The SIA 248 standard warns against delamination failures when the adhesive bed is too rigid. The flexibility of the binder is certified by the S1 and S2 indices, measured during a standardised transverse bending test on a hardened adhesive specimen.

Deformability classification and prescribed fields of application
ClassTransverse deformationRecommended typical applicationsBehaviour on the construction site
Without S indexLess than 2.5 mmDry interior walls, standard wall tiles, unheated floorsRigid, transmits all shear stresses to the tile.
Class S1Between 2.5 and 5.0 mmScreeds with underfloor heating, rigid wood panels, sheltered balconiesDeformable, absorbs the thermal differential between screed and porcelain stoneware.
Class S2Greater than 5.0 mmSunny outdoor terraces, ventilated facades, extra-large formatsHighly deformable, absorbs deformations without debonding.

For the installation of extra-large format porcelain stoneware with edges exceeding one metre twenty, the contact surface multiplies the stresses induced by thermal expansion. A C2 S1 class adhesive is the essential starting threshold indoors on a cement screed. If these dark slabs are installed on a balcony or outdoor terrace exposed to direct solar heat in summer and winter frosts, the tiler must switch to a C2 S2 class. This increased elasticity compensates for the low compressibility of thin joints and prevents shearing of the bonding ridges.

Selection of tile adhesive according to the mechanical and thermal stresses of the substrate

On Swiss construction sites subject to the requirements of the SIA 248 standard, choosing a tile adhesive is not just about raw adhesion. The C2 adhesion class guarantees an initial resistance and resistance after ageing of at least 1 N/mm², an essential threshold as soon as the tiling is subjected to thermomechanical stresses. Combining this base with deformability indices directly addresses the behaviour of structural work and finishing work. When tiling rests on underfloor heating or an exterior cladding undergoes temperature differences between winter frost and direct sunlight, deformability and substrate movement dictate the required class.

Tile adhesive selection matrix according to substrate and exposure (SIA 248 standard)
Structure configurationPredictable substrate movementsMinimum required classFunctional role of the indices
Interior cement screed with underfloor heatingCyclic thermal expansions, interface shearC2 S1The S1 index absorbs expansion stresses without breaking the bond.
Balcony or outdoor terrace (porcelain stoneware slabs)Severe thermal shocks, high summer/winter gradientC2 S2 EClass S2 compensates for shrinkage and swelling; class E secures installation in windy conditions.
Liquid waterproofing system under tiles (SELC)Membrane elasticity, bridged micro-crackingC2 S1Flexible bond compatible with the modulus of elasticity of the waterproof membrane.
Ventilated facade or bonded exterior wallDifferential expansion, wind load, dead weightC2 S2 TThe T index prevents vertical slip under the weight of large elements.
Dry screed or rehabilitated timber floorDeflection under service load, vibrationsC2 S2Transverse deformation greater than 5 mm to absorb panel bending.

Shearing at the edges is the main risk when heating coils are activated or in the event of low-angle sunlight on large tiles. If the mortar is too rigid, the stress is not dissipated within the thickness of the adhesive: it concentrates at the screed-tile interface, causing debonding through cohesive failure of the substrate or clean detachment. The SIA 248 standard reiterates the need to strictly comply with movement joints and perimeter expansion joints to limit these allowable stresses.

Execution impacts on the construction site: managing open time and skinning

The letter E indicates an extended open time. On site, this characteristic transforms the installation pace of tilers. Conventional mortar without option E begins to form a dry surface skin, known as a skinning film, after 15 to 20 minutes of spreading with a notched trowel. As soon as this film appears, the mortar no longer wets the back of the tile properly: effective adhesion drops below the required values without the installer noticing during application.

  • Systematic tactile check: the team leader or tiler places a finger on the adhesive ridges; the paste must stick firmly and stain the skin without leaving a dry film.
  • Progressive pull-off test: lift a tile immediately after beating down to check for full adhesive transfer, with no hollow areas under the ceramic.
  • Critical weather environment: in the presence of draughts on landings or active site heating, the actual open time of normal adhesive can drop to less than 10 minutes; class E provides the essential safety margin.
  • Large format and complex setting out: handling a slab using a vacuum suction frame requires several minutes of fine adjustment; the E index prevents the ridges from drying out during tile adjustment.

The alternative of class F, which designates a fast-setting mortar, addresses opposite issues. With hardening occurring within a few hours, it allows grouting on the same day and express reopening to traffic. However, its open time is significantly reduced, often hovering around 10 to 15 minutes. Its use requires an experienced team working with small mixes and very limited spread surfaces.

Managing adhesion defects and making decisions on unstable substrates

On site, poor diagnosis of the adhesive-substrate pairing immediately translates into visible signs: early formation of a skin on the surface of the setting bed, zero transfer to the back of the ceramic, or hollow sound when tested with a sound meter after hardening. When ambient conditions accelerate evaporation or when the required flexibility for a substrate subjected to thermal stress has been underestimated, the artisan must stop installation to prevent the creation of widespread structural failure.

  1. Immediate transfer checkAs soon as there is any doubt about surface drying, lift a fresh tile to inspect the wetting. If the striped ridges remain neat without uniform crushing or if the transfer rate on the back of the piece is not total, immediately scrape off the altered mortar from the substrate and re-bond it from scratch.
  2. Checking substrate movementsWhen facing underfloor heating or a prefabricated element subject to shrinkage, compare the deformability class of the product used with the edge length of the installed tiles. On an unstable element, promptly replace a standard reference with an S1 or S2 classified mortar to absorb shear forces without breakage.
  3. Requalification of the installation assemblyAdapt the choice of adhesive by including the extended open time for days with an east wind or dry heat. In the event of a clear mismatch between the planned supply and the actual building environment, record the technical findings in writing before resuming any activity.

Rigorous management of these interfaces ensures compliance of the structure according to the SIA 248 standard. Correct selection between base adhesion, extended skinning time, and flexibility against expansion avoids destructive complete retiling operations.

Frequently asked questions

How to spot tile adhesive that has exceeded its open time during installation?

The fingertip tactile test is the quickest method at the workstation. By lightly touching the spread mortar ridges, the paste must stick firmly and stain the skin. If the surface has a matt appearance, is dry to the touch, and no material remains stuck to the glove, skinning has occurred: the setting bed must be scraped off and replaced before applying any tile.

Why does a large-format tile require a C2 S1 or S2 class on a heated screed?

Heating and cooling cycles induce continuous dimensional variations between the mineral screed and the porcelain stoneware, which is a very rigid and non-absorbent material. The longer the edges of the tile, the more destructive the shear forces at the ends become. A deformable adhesive classified as S1 or S2 provides the transverse elasticity necessary to absorb these differential movements under the ceramic covering without risking debonding or cracking of the installed tiles.

What should be done when tile adhesive starts to set in the bucket before application is complete?

The mix must be discarded without attempting to rehydrate it. Late addition of water fluidises the mixture in appearance but breaks the cement hydration molecules, degrading the tensile strength prescribed by the SIA 248 standard. The altered paste loses its mechanical strength and bonding power. On site, the only correct course of action is to clean the tools, empty the container, and mix a new batch of a volume suited to the work pace.

What is the concrete difference on site between a C2TE mortar and a C2E mortar?

The letter T indicates resistance to vertical slip, an essential property for wall installation of wall tiles and heavy formats. It prevents the instantaneous sagging of the piece under its own weight during application. The C2E reference does not guarantee this slip resistance but, like the C2TE variant, offers an extended open time of up to thirty minutes, allowing large floor areas to be spread without the risk of premature dry surface skin formation.

Texts and standards cited

  • SIA 248Installation of tiles and ceramic and natural stone coverings, execution prescriptions and rules of the art relating to substrates and bedding mortars.

In the same section