Key takeaways
- An adhesive that has formed a surface skin no longer ensures any transfer onto the tile.
- Standard SIA 248 prescribes perfect adhesion requiring rigorous control of the open time.
- The tactile finger test every few minutes remains the only reliable evaluation method.
- Advance spreading must be restricted to surfaces that can be tiled in under ten minutes.
Skin formation and drop in open time according to standard SIA 248
On a tiling construction site in Switzerland, the practical open time very rarely corresponds to the theoretical values stated on tile adhesive bags. Standard SIA 248 governs the installation of ceramic coverings and requires achieving intimate, durable contact between the binder, the substrate and the back of the tiles. In the laboratory, the standardized open time is evaluated in a controlled environment at twenty-three degrees and fifty percent relative humidity, generally reaching twenty to thirty minutes for a standard-class mortar. On a concrete slab or cement screed in a real-world situation, drafts, direct sunlight through large bay windows, and residual porosity drastically reduce this interval, sometimes to less than ten minutes.
- Practical open time
- Maximum interval between spreading the tile adhesive on the substrate and the precise moment when laying the tile still guarantees the transfer rate and adhesion prescribed by standard SIA 248.
The critical phenomenon is skin formation. As soon as it is spread with a notched trowel, the mixing water evaporates rapidly at the top of the ridges under the effect of the ambient air, while the substrate absorbs another fraction by capillarity. A thin, matt and deceptively dry film thus forms on the surface. Deep down, the adhesive bead remains completely fresh and malleable, which deceives the inattentive tiler. If a tile is pressed down onto ridges that have formed this skin, the mass flattens without wetting the back of the ceramics. The mechanical adhesion is then zero.
| Ambient temperature | Relative humidity | Nominal open time | Actual open time on construction site |
|---|---|---|---|
| 10 °C to 15 °C | 70 % | 30 minutes | 25 to 30 minutes |
| 20 °C to 23 °C | 50 % | 30 minutes | 15 to 20 minutes |
| 25 °C to 30 °C | 40 % (draft) | 30 minutes | 5 to 10 minutes |
| > 30 °C | < 35 % (sunlight) | 30 minutes | Less than 5 minutes |
Systematic finger test and management of combed surfaces
Checking the surface condition of the tile adhesive requires no complex equipment: the tactile finger test is the golden rule on the construction site. Every few minutes, the tiler must place the pad of the index finger on the crest of the ridges without applying excessive pressure. If the adhesive adheres firmly to the finger and leaves a distinct pasty trace on the finger upon withdrawal, tile wetting remains guaranteed. On the other hand, if the finger comes out clean or merely dusty, even if the underlying material is pliable, the skin has formed. It is then strictly forbidden to lay the ceramic element.
- Regular tactile checkLightly touch the crest of the spread ridges every three to five minutes, particularly on the first combed area.
- Skinning observationCheck the transfer onto the index finger. A complete absence of liquid transfer requires the immediate cessation of tiling in this area.
- Removal of wind-affected adhesiveScrape off the altered tile adhesive completely using the edge of the trowel and discard it. Never re-moisten or reload directly.
- Immediate re-applicationBriefly clean the residual substrate and comb a fresh pass taken from the bucket before continuing tile adjustment.
To prevent this defect, the elementary rule consists in drastically limiting the surface area bonded in advance. Too often, in order to progress quickly, workers spread two to three square metres of adhesive. In the presence of an inactive but warmed underfloor heating system, or a room ventilated in dry weather, the last square metre of adhesive applied is inevitably wind-affected before being covered. The pre-combed surface must strictly correspond to what the layer can cover in less than ten minutes, generally the surface of a single large format or two to three medium tiles.
Construction site ambient conditions and sizing of spreading passes
On construction sites in French-speaking Switzerland, the theoretical open time value provided in tile adhesive technical datasheets is measured in a standardized laboratory, i.e., at twenty-three degrees and fifty percent relative humidity without air currents. In the reality of a floor under finishing work or a room exposed to large bay windows, these ideal parameters are almost never encountered. The combined action of a high ambient temperature, a heavily thirsty cement screed substrate, and a passing draft accelerates the evaporation of the mixing water. This phenomenon sometimes divides the useful installation window by three or four, transforming a theoretical open time of thirty minutes into a critical interval of less than ten minutes.
To maintain adhesion in compliance with standard SIA 248 requirements, the tiler must adapt the combing pace to the room's actual climate. The most costly mistake is to comb out the footprint of several large tiles in one go to save handling time. As soon as air circulates between two openings or the sun hits the floor directly, the surface of the ridges dehydrates extremely rapidly. The professional therefore adjusts their advance to the nearest square metre: they spread only the quantity of tile adhesive they are capable of covering, beating, and adjusting before the very first hint of surface desiccation.
| Room conditions | Estimated effective open time | Maximum spread surface area | Required organizational measure |
|---|---|---|---|
| 10 °C to 15 °C, RH > 70 %, no draft | 25 to 30 minutes | 3.0 to 4.0 m² | Standard progression, monitoring of setting time |
| 20 °C, RH ~ 50 %, closed ventilation | 15 to 20 minutes | 2.0 to 2.5 m² | Regular pace, tactile check per bay |
| 25 °C to 30 °C, dry air or heated floor | 8 to 12 minutes | 1.0 to 1.5 m² | Tile-by-tile installation, adhesive mixed in small batches |
| Active draft (open doors/windows) | 5 to 8 minutes | 1 tile at a time | Immediate sealing of openings, strict double-gluing |
The behavior of mineral substrates accentuates this phenomenon. An anhydrite or cement screed that is unprimed or whose primer is not completely dry will literally pump the water out of the adhesive bed from its base, while ambient air dries out the top of the combed ridges. The use of a deformable tile adhesive classified as C2 TE or S1 slightly delays the formation of this film thanks to specific water-retention admixtures, but it never exempts the tradesperson from rigorous surface condition checks before each ceramic contact.
Detection of loss of adhesion, destructive sounding and remediation protocol
When a tile is laid on an adhesive whose surface skin has closed up, the defect is immediate but invisible to the naked eye. The ridges flatten under pressure or beating, giving the misleading illusion that the bed has transferred to the back of the piece. In reality, the dried film forms an impenetrable screen: polymers and hydraulic binder do not penetrate the pores of the ceramic or porcelain stoneware. The mortar will cure properly on the screed, but the interface with the slab will remain free of any mechanical and chemical bonding. In the medium term, thermal expansion or simple pedestrian traffic will unbond the covering, causing hollow sounds under the mallet.
To guarantee the compliance of the work according to standard SIA 248, the tiler must validate the quality of the transfer during installation. The only foolproof method is to carry out an immediate destructive check by lifting the first tile of a freshly beaten series. The tile adhesive bed must coat the reverse side of the tile homogeneously, without breaks or dry areas. If the back of the ceramic remains clean or only shows traces of moisture without effective transfer of pasty material, the adhesive in place is spent.
- Observation and stoppage of installationAs soon as the tactile finger test reveals an absence of adhesion or a lifted control tile shows insufficient transfer, suspend the installation of ceramic elements on the bonded area.
- Complete scraping of the degraded bedImmediately remove the altered tile adhesive using a trowel or a rigid metal scraper until sound substrate or the initial contact layer is reached. Never reincorporate these dry residues into the mixing tub.
- Cleaning the back of the tilesCarefully clean the back of the tile(s) that came into contact with the skinned adhesive using a damp sponge, in order to remove any trace of powdery film likely to impair subsequent re-bonding.
- New combing on a reduced surface areaRe-apply a layer of fresh tile adhesive onto the prepared substrate, reducing the pre-combed surface area to a dimension compatible with the humidity and the crew's pace.
Rigorous management of open time falls directly under the applicator's responsibility. The time spent scraping a square metre of wind-affected adhesive represents a loss of a few minutes on the daily schedule, whereas repairing a debonded flooring after handover generates disproportionate rework costs including demolition, removal of skirting boards and repair of movement joints.
Procedure to follow in case of crusted adhesive and remediation of non-compliant surfaces
If the finger test reveals zero transfer or if a lifted control tile shows unflattened and dry ridges, the verdict is final. The skin formed on the surface constitutes an irreversible interface rupture between the mortar and the tile. Forcing an installation onto crusted adhesive does not reactivate the emulsion in any way: the ridges appear to flatten under blows from the beating block or mallet, but the back of the ceramic remains devoid of adhesion. According to standard SIA 248, the transfer rate must be total outdoors or under severe loads, and predominant indoors to guarantee the durability of the work under traffic.
- Complete disposal of the altered areaScrape off the skinned tile adhesive without delay using a trowel or a straight spatula down to the sound substrate, before the hydraulic setting begins. Dispose of these residues as waste; it is strictly forbidden to reintroduce them into the mix.
- Careful cleaning of the substratePass a carefully wrung-out damp sponge to remove the residual binder film on the screed or smoothing compound, without soaking the mineral base. Allow all traces of shiny moisture to evaporate before applying a new layer of fresh mortar.
- Strict readjustment of the spread footageReduce the pre-combed surface to a single row or to the exact footprint of a single large-format slab. This precaution is essential in hot, ventilated environments or on absorbent substrates, to align progress with the actual open time of the workplace.
In case of persistent doubt after laying a series of slabs, the site manager carries out a mallet sounding after twenty-four hours of curing. Localized hollow resonance unmistakably betrays the initial wetting defect. The concerned elements must be removed, the hardened bed mechanically stripped by chiselling or grinding without damaging the slope formation or underlying waterproofing, and then re-laid according to the requirements of standard SIA 248 with a fresh mix.
Frequently asked questions
How does the tiler concretely perform the finger test on the combed adhesive?
Place the index finger on the crests of freshly combed adhesive without applying excessive pressure. If the adhesive adheres to the finger and leaves a distinct mark, the open time is respected and the transfer to the back of the tile will take place correctly. If the finger comes out clean or merely dusty, a skin has formed: the adhesive will no longer wet the ceramic body. Any spreading showing this symptom must be scraped off and re-applied.
What surface area of tile adhesive can be combed in advance without risking crusting?
The maximum surface area must not exceed what can be covered in ten to fifteen minutes of effective work. With medium tiles, combing one to two square metres at a time is the safe limit. For large-format slabs or in the presence of drafts and temperatures above twenty-five degrees, spread the adhesive only for the piece currently being laid, tile by tile, in accordance with standard SIA 248.
Why is it forbidden to re-moisten adhesive whose surface has skinned?
Adding water to a combed adhesive during setting washes out the polymers and breaks down the water-cement ratio at the surface. The thin film thus created loses its mechanical properties and forms a friable release barrier. Even if the adhesive appears pliable again, the binder is definitively altered. The tile laid on this degraded emulsion will detach under the first thermal or mechanical stresses during the operation of the structure.
What should be done when a tile sounds hollow the day after its installation?
The hollow sound reveals a lack of direct contact attributable to exceeding the open time or insufficient flattening of the ridges. Standard SIA 248 requires continuous adhesion. The unbonded tile must be removed without delay, the hardened adhesive removed with a flat chisel without damaging the screed, the area dusted off and re-bonded with fresh mortar by applying careful double-gluing to ensure total wetting of the back of the element.
Texts and standards cited
- SIA 248Installation of tiles and ceramic and natural stone coverings
