Skip to content
Website
🧱 CFC 282Substrate acceptance and preparationChapter 6 of 10 in the section

On old substrates: conditions, degreasing, primer, and lost height

Direct bonding onto existing tiles avoids heavy demolition but presents major risks of debonding. You will learn how to methodically sound the existing covering according to SIA 248 requirements, carry out technical degreasing, choose the appropriate bonding primer and precisely calculate the extra thickness to prevent jamming at door thresholds and connections.

Key takeaways

  • Systematic mallet testing guarantees mechanical stability with no underlying loose tiles.
  • The old covering must be thoroughly degreased using alkaline washing followed by neutralization before any work begins.
  • A silica-filled bonding primer creates the essential roughness on non-absorbent glaze.
  • The total extra thickness of between ten and fifteen millimetres makes it necessary to adapt doors and transition profiles.

Validate the four technical conditions before starting any overlay work

Covering existing ceramics is a common solution in renovation work to reduce noise nuisance, dust and intervention times. However, the trade regularly advises against this method: it masks defects without fixing them and transfers mechanical stresses to an unknown interface. To undertake this process without causing foreseeable defects, four cumulative conditions must be strictly met on the original substrate: absolute structural stability of the floor, flawless mechanical adhesion of every tile, a perfectly flat and sound surface, and a clearance geometry compatible with adjacent rooms.

  • A monolithic bond to the raw substrate: no split, loose or hollow-sounding tiles when tapped.
  • Strict flatness tolerance: compliance with surface criteria according to SIA 248 standards.
  • Total absence of underlying defects: no rising capillary dampness or untreated active structural cracks.
  • Altimetric compatibility: sufficient clearance for doors, skirting boards and fixed elements without level differences.
  1. Element-by-element acoustic soundingTap the entire tiled surface using a hard-headed mallet or tapping rod. Locate and mark with chalk each tile producing a hollow sound.
  2. Stripping and removal of unstable areasRemove all hollow-sounding tiles, as well as cracked or unseated elements, using a light pneumatic chisel. Remove old mortar residue down to the solid slab or screed.
  3. Patching and localized smoothingFill the cleared cavities using a fast-setting, shrink-compensated repair mortar. Level the surface perfectly to re-establish the general level before applying any primer.

Chemical cleaning, bonding agent and management of clearance heights

The glaze of a vitrified tile or the polishing of porcelain stoneware creates a closed, smooth surface free of porosity. No standard tile adhesive can develop durable mechanical anchorage on it without proper chemical and mechanical preparation. The first operation consists of removing operational grease, maintenance waxes and soap residue by intensive alkaline degreasing. After rinsing with clean water and complete drying, the application of a specific bonding primer is mandatory. This single-component primer, formulated from synthetic resins and filled with quartz sand, creates an artificial roughness essential for preventing slip and ensuring the transfer of adhesive bond.

The second pitfall of overlaying lies in the final altimetry. Adding a new combined tile and adhesive thickness changes the finished level by ten to fifteen millimetres. This extra thickness directly affects door thresholds, carpet or parquet joints, and existing wooden skirting boards. While solid wood interior doors can be planed in the workshop, armored landing entrance doors, metal door frames or fire doors do not allow any trimming without altering their safety certification. The tradesperson must accurately measure this dimension using a straightedge and spirit level during the preliminary visit to report the incompatibility before work begins.

Typical calculation of extra thickness when bonding over old tiles
Component of the assemblyAverage thicknessImpact on the construction site
Quartz bonding primer< 1 mmRoller application, drying time of 2 to 4 hours
C2 deformable tile adhesive3 to 5 mmMandatory buttering-floating, notched trowel suited to the format
Renovation porcelain stoneware8 to 10 mmChoice of calibrated and rectified tile
Total finished extra thickness12 to 16 mmTrimming of door leaves and bevelled threshold bars

At passages between tiled rooms and neighboring parquet floors, the extra thickness creates a distinct step. The tradesperson must install compensating angle transition profiles in aluminum or brass to bridge the gradient without creating a tripping hazard. If underfloor heating is present beneath the original tiling, the client must also be warned of the additional thermal inertia provided by this double ceramic layer.

Adhesion testing and stripping of hollow tiles in accordance with SIA 248

Direct overlaying of old tiles cannot be considered without comprehensive mechanical inspection of the existing installation. According to trade rules and SIA 248, the tiler must check the cohesion of each element with its original substrate. A tile that sounds hollow indicates a clear debonding of the setting mortar or detachment from the screed. Retaining such an area under a new layer transfers shear stresses to the new assembly, leading in the short term to surface cracks and the loosening of recently bonded slabs.

  1. Mallet or tapping rod soundingInspect the entire surface tile by tile using a tiler's mallet or rubber club. Tap lightly on each corner and the center. Any dull or hollow sound must immediately be marked with a grease pencil on the covering.
  2. Selective removal of non-adherent elementsStrip all loose or debonded tiles using a flat chisel mounted on a light rotary hammer, taking care not to fracture the underlying screed or disturb neighboring healthy elements.
  3. Removal of adhesive and mortar residueScrape away residual adhesive under the stripped elements to reach the hard mineral substrate. Vacuum rubble and fine residue using an industrial vacuum cleaner equipped with a fine dust filter.
  4. Patching with fast-setting repair mortarApply a mineral primer to the base of the excavation and then fill the created clearances with a thixotropic leveling mortar or shrink-compensated repair mortar, struck off level with the retained tiles.

Management of extra thickness, caulking and adaptation of door thresholds

Installing new tiles over existing ceramics inevitably changes the finished altimetric level of the room. This extra thickness, generally between 12 and 18 millimetres, has a direct impact on reveals, skirting boards, door frames and connections with adjoining rooms. If the initial planning neglects this dimension, the tiler will be unable to install edge profiles and will block the movement of door leaves.

Breakdown of lost height during bonded installation on existing tiles
Element of the assemblyMinimum thicknessMaximum thicknessImplementation observations
Bonding primer< 0.5 mm1.0 mmSynthetic resin with silica or special dispersion
Possible correction / smoothing0.0 mm3.0 mmRequired if there are flush offsets (lippage)
Deformable tile adhesive bed3.0 mm5.0 mmApplication with 8 to 10 mm notched trowel using buttering-floating
New porcelain stoneware tile8.0 mm12.0 mmVariable depending on format and load requirements
Total lost height11.5 mm21.0 mmRough dimension to deduct beneath openings and thresholds

Managing door passages requires precise technical coordination. The bottom of metal door frames cannot always be easily trimmed on site; extra-thick tiling will butt against the frames or prevent the subsequent removal of doors without specific unhinging. For interior wooden doors, bottom planing is essential to maintain the required clearance under the door leaf, particularly if controlled mechanical ventilation requires airflow.

  • Check existing air gaps under each door leaf before approving the overlay project.
  • Systematically install a solid stainless steel or brass mechanical transition threshold profile to bridge the level difference towards adjacent rooms.
  • Avoid abrupt drops creating a dangerous step: prioritize a chamfered profile ensuring a gentle slope.
  • Maintain a 5 millimetre perimeter movement joint at the bottom of frames and lightweight partitions, caulked with a flexible bead.

Handling non-conformities: substrate rejection, blocked thresholds and debonding

When acoustic mallet testing reveals more than 10% unseated tiles or altimetric inspection highlights the technical impossibility of connecting landings, the tiler must stop work. According to SIA 248, the existing substrate directly engages the applicator's liability as soon as they agree to install a new bonded covering on it. Continuing installation on a cracked, unstable floor saturated with ungreased domestic cleaning products will inevitably lead to generalized delamination under shear stresses.

Faced with an incompatible substrate or insoluble altimetric conflict, the contractor shall without delay forward a written notice of defects to the site management and the client, in accordance with the principles of the Code of Obligations and SIA 118 governing construction contracts. This technical record logs the measured elements: percentage of hollow tiles, untreated through-cracks, or unacceptable reduction of water clearance at exterior patio door thresholds.

  • Stoppage of installation work and immediate transmission of a record of incompatibility with joint records.
  • Technical proposal for complete removal of the old tiling by mechanical chiselling down to the original screed.
  • Preparation of a supplementary quote covering rubble disposal, substrate sanding and application of a fiber-reinforced self-levelling compound.
  • Implementation of a local variant by surgically removing debonded elements and patching with fast-setting repair mortar.

Complete demolition of the old covering is almost always the most rational decision in interior renovation. It sanitizes the structure, neutralizes the risk of crack telegraphing or non-aligned joints and preserves the original altimetric level. If the client maintains their order to tile over the old covering despite the reservations expressed, the tiler formally refuses the warranty on adhesion and demands a written order confirming assumption of risk by the client.

Frequently asked questions

Can you tile directly over old tiles without applying an adhesion primer?

No, this is strictly ruled out on vitrified or glazed tiles. Existing tiles have virtually zero porosity, which prevents the mechanical anchorage of standard tile adhesives. After meticulous alkaline degreasing and rinsing with clean water, it is mandatory to apply a specific quartz-sand-filled bonding primer or appropriate adhesion resin. Direct installation would lead to complete debonding of the new ceramic under the effect of thermal variations and foot traffic.

How should old hollow-sounding tiles be treated before installing the new tiling?

Any tile that sounds hollow when tapped must be removed using a flat chisel. If less than 10% of the total surface is affected, unstable pieces are extracted, residual dust is vacuumed, and the cavities are filled flush with repair mortar or a class C2 tile adhesive. If the hollow surface exceeds this threshold, the overall adhesion of the original tiling is compromised: total demolition of the work must then be specified.

What minimum total thickness must be allowed for when bonding over existing tiles?

An overall extra thickness of between 12 and 16 mm must be allowed. This dimension incorporates the primer film, the crushed tile adhesive bed (approximately 3 to 5 mm for buttering-floating with a notched trowel) and the thickness of the new porcelain stoneware tiles (often 8 to 11 mm). This additional height must be anticipated for interior door clearance, surface-mounted skirting boards, stair connections and kitchen plinths under worktops.

Is it possible to cover old tiles laid over operating underfloor heating?

This is technically feasible but thermally detrimental. Adding a second layer of ceramics and an adhesive bed increases the inertia and overall thermal resistance of the floor diffuser, reducing system efficiency. It is imperative to switch off the heating 48 hours before work and use an improved deformable tile adhesive, class C2 S1 or S2 according to SIA 248, capable of absorbing differential expansion between the two superimposed layers of tiles.

Texts and standards cited

  • SIA 248Tiled coverings and mosaics
  • SIA 118General conditions for the execution of construction work

In the same section