Skip to content
Website
🧱 CFC 282Section 2 of 610 chapters

Bonded waterproofing in wet rooms: the execution reference framework

This section details the implementation of bonded waterproofing systems for wet areas in Swiss buildings. Intended for team leaders, tilers and site managers, it covers bridging methods, rigorous treatment of penetrations and the management of critical joints. The objective is to master the thin water-repellent barrier to exclude any risk of infiltration into underlying structures and neighbouring apartments.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

Professional tiling technical datasheets

200 cm

Waterproof upstand above the shower floor or tray

Norme SIA 248

1.0 mm

Minimum thickness required for a two-component waterproofing mortar

Norme SIA 248

0.5 mm

Minimum thickness of a dispersion-based liquid waterproofing system

Swiss professional tiling guidelines

24 hours

Minimum duration of a water-filling test before tiling installation

Scope of work and limits of the tiler's services

Bonded waterproofing falls directly under the tiler's responsibilities under CFC 282. It includes the application of liquid waterproofing membranes, glued synthetic mats, reinforcement tapes at corners and flexible waterproof collars around pipes. The sole purpose of this continuous envelope is to intercept water infiltrating through the tiling and mineral joints before it reaches the screed assembly or masonry.

Demarcation of responsibilities according to the Swiss CFC
Work elementResponsible tradeTiler's service (CFC 282)
Slope formation and bedding screedScreed and fluid screed (CFC 281)Planeness check, residual moisture measurement, degreasing
Underfloor heatingHeating installations (CFC 241)Verification of the initial heating-up protocol
Drainage and trap bodySanitary installations (CFC 250)Supply and bonding of the waterproofing sleeve onto the collar
Flat roof / suspended balcony waterproofingStructural waterproofing (CFC 226)Tiling installation on drainage mat excluding roof waterproofing
Plasterboard partitioningPlastering and false ceilings (CFC 271)Suitable primer and bonded waterproofing system
Protection against leaks under tilingTiling and wall tiling (CFC 282)Complete installation of corner tapes, mats, sleeves and thin resins

This section does not under any circumstances cover heat-welded bituminous or synthetic membranes for flat roofs, which are the responsibility of waterproofing contractors under CFC 226. It focuses on composite systems applied by trowel or roller, bonded directly to ceramics or natural stone.

Methodical execution workflow and defect prevention

Bonded waterproofing does not forgive any discontinuity. Claims observed in Western Switzerland almost never result from a rupture of the material across the main surface, but from a neglected joint or a disrupted order of work. The ten chapters of this section follow the actual chronological order of the construction work, from the design of upstands to the handover of the work to the client.

  1. Demarcation of zones and protection heightsIdentify moderate and heavy stresses to determine mandatory upstand heights on shower walls and around bathtubs.
  2. Treatment of technical penetrations and cornersPosition the elastomer sleeves on the concealed tap connections and embed the corner tapes into the first fresh layer.
  3. Application under thickness controlRespect the surface coverage guaranteed by the manufacturer by applying two cross-coats verified with a wet film thickness gauge.
  4. Preliminary tests and final installationSystematically carry out the watertightness test by filling with water before bonding the covering, then create the flexible perimeter caulking without damaging the continuous film.

The management of bonded waterproofing requires rigorous coordination with the sanitary plumber and the partition installer. The execution of each step must be verifiable by thickness checks and construction site photographs before complete covering by adhesive and tiles.

📘 Chapters in this section 10

Waterproofing beneath tiles in wet areas

Where waterproofing is required: shower, bathtub, wet room floor and upstand height

Master the regulatory installation perimeters and application heights to perfectly secure every wet room.

Waterproofing beneath tiles in wet areas

The collar: bonded to the outlet, embedded in the waterproofing, and the water damage it prevents

Discover the precise embedding of sleeves to permanently eliminate invisible leaks along pipes.

Waterproofing beneath tiles in wet areas

Corners: flexible tape at the base, differential movement and waterproofing failure

Learn how to effectively bridge floor-to-wall connections to absorb all structural movements without rupture.

Waterproofing beneath tiles in wet areas

Thickness: consumption per square metre, two cross coats and moisture check

Guarantee the continuity of the membrane by respecting consumption rates and gauge controls.

Waterproofing beneath tiles in wet areas

Never drill afterwards: shower rail, shelf, and any drilling that penetrates the waterproofing

Protect your waterproofing from equipment penetrations to preserve the integrity of the work and your professional responsibilities.

Waterproofing beneath tiles in wet areas

Testing before tiling: water filling, duration, check at the neighbour's and photo

Validate the reliability of your membrane through a recorded water-filling protocol before tiling.

Waterproofing beneath tiles in wet areas

The flexible joint: corners, appliance perimeters, mold and periodic replacement

Apply the waterproofing sealant correctly to ensure flexible and durable connection joints.

Waterproofing beneath tiles in wet areas

Prefabricated shower tray or on-site waterproofing: compared risk, cost and schedule

Methodically compare prefabricated trays and site-cast waterproofing to make the safest choice.

Waterproofing beneath tiles in wet areas

Tiled balcony: waterproofing, drainage, frost, and the boundary with structural waterproofing

Distinguish bonded waterproofing from exterior works to drain water without suffering frost damage.

Waterproofing beneath tiles in wet areas

The claim: forgotten collar, damage at the neighbor's and full repair under warranty

Analyze the typical sequence of failures to guard against particularly costly remedial construction work.