Skip to content
Website
🧱 CFC 221Section 1 of 610 chapters

The three barriers: air, insulation, driving rain: the execution reference

Aimed at team leaders, foremen and site managers in the CFC 221 trade, this section structures the non-load-bearing envelope around three continuous layers: airtightness on the warm side, continuous thermal insulation and ventilated protection against driving rain. Based on the SIA 180 and SIA 331 standards, it details assembly rules, joinery connections and the management of penetrations to avoid any damage from condensation or water infiltration.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

OTConst art. 26

3 m

Fall height triggering the requirement for façade scaffolding

OTConst art. 26

80 cm

Minimum projection of the scaffolding top guardrail above the upper level

norme SIA 180

150 mm

Recommended minimum ground clearance at the foot of the cladding against splash-back

norme SIA 180

100 mm

Minimum horizontal overlap of flexible rain-screen membrane sheets

Technical scope of the façade installer and role of the three barriers

The building envelope relies on a strict physical logic governed by standard SIA 180 for hygrothermal performance and standard SIA 331 for external joinery. Each external wall must absolutely combine three independent and uninterrupted functions: the airtightness barrier on the interior side, the intermediate thermal insulation layer and the drained rain-screen barrier on the exterior side. The absence or breach of just one of these layers inevitably leads to serious defects such as interstitial condensation, deterioration of timber structures or excess energy consumption.

The installer and the façade worker operate at the direct interface between the regulated interior environment and the weather. On the warm side, the vapour check or vapour barrier blocks convective moisture transfer caused by pressure differences. In the middle, the insulation must fit tightly against the masonry or the rafters without any circulating parasitic air gap. On the cold side, the rain-screen membrane collects residual infiltration behind the cladding and channels it outwards by means of a ventilated air cavity that complies with the rules of the art.

  • Airtight barrier: continuous interior membrane, joints bonded to dedusted concrete, sealed collars on every service duct.
  • Insulating barrier: tightly butted panels, clean cuts compressed by 5 mm, complete sealing of window reveals without thermal bridges.
  • Driving-rain barrier: UV-resistant membrane, minimum overlaps following the direction of water run-off, minimum continuous rear ventilation from bottom to top.

Execution method and logical order of work

The technical success of a façade construction site depends on the sequence of operations. Installation of a rain-screen membrane never begins before the continuity of the insulation has been accepted, just as no interior lining is closed before the collars on the service penetrations have been bonded and checked. The ten chapters of this section follow the real progression of the construction site, from hygrothermal design to the final interface inspection.

  1. Definition of airtightness and treatment of penetrationsSelect the appropriate Sd value according to the wall build-up, position the membrane on the warm side of the insulation, then immediately treat every corner connection, window reveal and duct passage with compatible adhesive tapes and primers suited to mineral substrates.
  2. Continuous thermal sealing and management of singular thermal bridgesChoose stable rigid or semi-rigid panels, adjust cuts to eliminate any millimetre-sized gap, double the layers with staggered joints to cover weaknesses, and return the insulation over lintels and splayed reveals in accordance with the requirements of standard SIA 180.
  3. External protection, water management and low-level cut-offsInstall the rain-screen membrane from bottom to top with draining overlaps, fix the ventilation battens, respect the minimum ground clearance at the foot of the façade to prevent capillary rise, and hold the closing meeting before the wall is finally closed.
Roles and critical requirements of the three façade barriers
Functional layerKey standardSite checkpointConsequence of a defect
Airtightness (warm side)SIA 180Continuity of adhesives on primed concreteSevere interstitial condensation in winter
Thermal insulation (middle)SIA 180Tight fit without rear convectionInterior mould due to lowered surface temperature
Ventilated rain screen (cold side)SIA 331Overlaps, sealing of flashings and rodent grillesLiquid water infiltrating the mineral wool

📘 Chapters in this section 10

The three barriers: air, insulation, driving rain

Vapour barrier or vapour retarder: which one, and on which side of the insulation

Position the right membrane in the right place to rule out any risk of destructive condensation.

The three barriers: air, insulation, driving rain

Airtightness continuity: treat the singular points before closing up

Secure every corner, duct and pre-frame before the wall is finally sealed.

The three barriers: air, insulation, driving rain

Rainscreen membrane: laying direction, overlap and permissible exposure time

Ensure perfect drainage of rainwater by controlling overlaps and exposure times.

The three barriers: air, insulation, driving rain

Adhesives and tapes: compatibility with the substrate and preparation

Select the adhesives, primers and tapes suited to each substrate to guarantee lasting airtightness.

The three barriers: air, insulation, driving rain

Geometric thermal bridges: corners, lintels and insulation returns

Treat joinery connections meticulously to eliminate the thermal bridges that cause mould.

The three barriers: air, insulation, driving rain

Interstitial condensation: understanding where water forms and how the wall dries out

Understand the hygrothermal behaviour of walls to facilitate the rapid removal of any residual moisture.

The three barriers: air, insulation, driving rain

Choosing the insulation: conductivity, long-term performance and fire behaviour

Combine thermal performance, mechanical stability under the battens and cantonal fire protection requirements.

The three barriers: air, insulation, driving rain

Installing insulation without gaps: tight cuts, double layer and parasitic air gaps

Fit your insulation cuts to the millimetre to eliminate the parasitic air gaps that degrade efficiency.

The three barriers: air, insulation, driving rain

Façade base: plinth, capillary break and ground clearance

Take care with ground clearances and capillary breaks at the wall base to protect the lower framework.

The three barriers: air, insulation, driving rain

Before closing the wall: the meeting that avoids reopening

Organise the key coordination with the other trades before closing off your wall assemblies.