Skip to content
Website
🧱 CFC 282Waterproofing beneath tiles in wet areasChapter 8 of 10 in the section

Prefabricated shower tray or on-site waterproofing: compared risk, cost and schedule

This chapter provides the technical criteria for choosing between a tileable prefabricated shower tray and a liquid-applied waterproofing system on screed. You will learn how to assess the impact of integrated falls on the elimination of critical complex junctions, calculate the required recess height reserve and execute a watertight connection in accordance with professional tiling rules.

Key takeaways

  • The prefabricated board integrates a constant drainage fall and factory-secures the outlet connection.
  • The minimum recess height determines the integration of the trap and the zero-step floor element.
  • SIA 248 governs the adhesion and continuity requirements of under-tile membranes.
  • The perimeter bridging between the rigid element and the liquid screed forms the decisive waterproofing node.

Eliminating critical complex junctions thanks to the prefabricated tray

The walk-in shower is the structure most exposed to infiltration damage in Swiss finishing work. During traditional execution on a masonry fall-forming screed, the tiler must apply an under-tile waterproofing system directly to the screed. This method multiplies the critical phases: scrupulously observing drying times between coats of resin or polymer mortar, manual shaping of internal angle coves, roller-application of elastomer bands and adjustment of the waterproofing collar on the trap flange installed by the sanitary plumber. The slightest air bubble, film thickness defect or residual dust compromises overall impermeability.

Complex junction in wet area
Complex geometric area where mechanical stresses and infiltration risks concentrate: floor-wall internal angles, external angles, pipe penetrations and perimeter connection around the floor drain or trap body.

The prefabricated high-density extruded polystyrene rigid foam element, factory-faced with a glass-fibre mesh and a special mortar, structurally solves these difficulties. Its shape natively incorporates a calibrated fall of at least 1,5% to 2% towards the outlet, eliminating any risk of counter-fall or water pooling under the tiling. The sealing ring or connection sleeve is heat-welded or injected during the industrial manufacturing of the board. This eliminates the delicate step of manually gluing a waterproofing cuff onto the floor trap body.

Technical and organisational comparison: prefabricated versus on-site waterproofing
Site criterionReady-to-tile prefabricated elementUnder-tile waterproofing on screed
Drainage fallFactory-machined (guaranteed regularity)Manually pulled on screed (variable tolerance)
Connection to the trapIntegrated and secured waterproof ringAttached cuff glued on site
Work lead timeTiling possible after adhesive has driedWaiting for complete drying of the screed then the LWS
Risk of human errorLow, limited to perimeter connectionsHigh across the entire surface and angles

Required available height and connection to floor waterproofing

The integration of a walk-in shower requires rigorous coordination from the structural work phase to check the thickness reserve in the floor assembly. A prefabricated tray generally requires a total available height ranging between 65 mm and 120 mm. This dimension encompasses the thickness of the element itself, the horizontal or vertical trap body supplied under CFC 250, the standardised water seal, the minimum fall of the drainage pipe to the main stack, as well as the setting adhesive mortar bed. If the recess in the raw slab is insufficient, the tiler faces a technical impossibility of alignment with the finished floor level of the bathroom, creating an unacceptable step.

SIA 248 sets the professional rules relating to ceramic and natural stone coverings, in particular mortar adhesion requirements, substrate preparation and the continuous implementation of under-tile waterproofing in water-exposed areas.

Norme SIA 248

The nerve centre of the prefabricated structure now lies in its perimeter connection with the adjacent screed and wall partitions. A waterproofing failure at this junction causes major damage to the load-bearing structure or the flat below. To lock in this transition, the tiler must apply a non-woven elastomer waterproofing band, roller-pressed into a layer of two-component flexible waterproofing mortar, overlapping the board and the neighbouring substrate by at least 100 mm.

  1. Wedge-fitting and gluing of the boardCheck the flatness of the substrate or recess base. Coat the underside of the prefabricated board and the substrate using a deformable adhesive mortar applied with a notched trowel, ensuring full transfer without air voids.
  2. Mechanical connection to the drainage systemSecure the waterproofing collar to the receiving element of the trap by compressing the O-ring provided by the manufacturer, without crushing or deforming the drainage components.
  3. Bridging of perimeter jointsApply a first coat of waterproofing product straddling the edge of the tray and the adjoining screed. Embed the reinforced waterproofing band into the fresh mass using a smooth trowel, without forming creases.
  4. Continuity overlapDeposit a second coat of waterproof product over the bridging band, extending the application up wall angle upstands in accordance with best practice.

From a financial perspective, purchasing a complete prefabricated tray kit represents a higher material cost than the materials required for an on-site cast tray. However, this initial expense is offset by the reduction in installation time on the construction site and the virtual disappearance of rework resulting from flatness defects. Provided the recess constraints are controlled, the prefabricated system offers optimal legal and technical security for the tiling company.

Intervention lead times and installation rates according to SIA 248

Bathroom schedule management often encounters waiting times imposed by hydraulic binders and waterproofing resins. When a walk-in shower is shaped entirely on site, the tiler must comply with the rules of art enacted by SIA 248 regarding substrate maturity. Creating a traditional fall-forming mortar shape requires an incompressible hardening time before any under-tile waterproofing application. Even with a fast-setting mortar, applying a liquid waterproofing system requires two separate passes, separated by film drying and the embedding of corner bands, which immobilises the area for several working days.

The prefabricated tray made of extruded rigid foam coated with a special mortar reinforced with a glass fabric completely alters this operational chain. Its factory-integrated fall eliminates the mortar casting step. Once the element is fully glued to the prepared substrate using a deformable adhesive mortar and connected to the drainage trap collar, the area can receive its perimeter bridging treatment. The tiler can start laying the ceramic covering as soon as the bedding layer under the board has reached its initial strength, reducing work interruption to a few hours instead of two to three days.

  • Elimination of the waiting time for the dryness of the shaping screed.
  • Direct laying of ceramics without waiting for a second liquid coat to dry on the tray.
  • Foot traffic possible much faster for adjoining wall finishes.
  • Possibility of scheduling the tray installation, edge bridging and the first phase of tiling in a single working day.

Economic trade-off, risk management and decision matrix

Purchasing a ready-to-tile tray represents a higher initial material outlay than a simple bag of screed mortar and a few square metres of waterproofing mat. For a board with an integrated drainage frame, the supply expense is around 350 to 650 CHF depending on the format and drainage system, as detailed in the price series on /soumissions/. This amount is nevertheless amortised as soon as one calculates the volume of skilled labour hours required to profile four regular diamond points, roller-press the waterproofing mats without creases and ensure the watertight connection around the drainage collar.

Technical and operational comparison between in-situ waterproofing and ready-to-tile tray
Comparison criteriaMasoned shower with in-situ waterproofingPrefabricated ready-to-tile tray
Drainage fallManual shaping, risk of irregularity or water poolingConstant rectilinear fall guaranteed at factory (greater than or equal to 1.5 %)
Waterproofing managementMultiplication of connections at the trap and anglesContinuous surface waterproofing, factory-flanged waterproof collar
Labour timeHigh: shape pulling, drying, primer application, 2 waterproofing coatsReduced: direct full-coverage gluing, immediate perimeter bridging
Dead load on the floorSignificant (shaping mortar at least 40 to 60 mm thick)Negligible (high-density rigid foam weighing a few kilograms)
Infiltration damage riskSensitive to the execution quality of angles and the trap jointVery low on the tray surface, concentrated on the edge band

The trade-off must be guided by the site configuration. In apartment renovations or on older floors where the height reserve and permissible load are limited, the prefabricated tray is technically essential: it fits into reduced recess thicknesses while guaranteeing the regulated fall without excess weight. In new construction with tight deadlines or on repetitive multi-family housing sites, the manufactured element ensures execution quality, eliminates complaints related to counter-falls and frees up tiler hours for laying large formats or wall tiles.

Damage management and non-conformities: remediation protocols

When the altimetry of the recess delivered by the structural work or screed layer does not comply with the planned recess level, the tiler must reject the substrate before fixing the prefabricated tray. Insufficient residual height prevents ensuring the drainage outlet fall or creates an unexpected step at the shower entrance. If the tray is already glued with adhesive mortar and a level offset with the screed appears, correction is never done by overloading adhesive under the tiling. The prefabricated element must be removed while the mortar has not fully set, or the perimeter screed must be resurfaced with a compatible self-levelling mortar to re-establish perfect flatness continuity before applying the liquid waterproofing system.

In the presence of water infiltration detected during a water tightness test or reported on the lower level, troubleshooting begins with inspecting the connection area between the trap body collar and the board. If the factory-integrated waterproofing membrane or the perimeter waterproofing band has unbonded due to insufficient crushing of the waterproofing mortar, spot resin injection is prohibited. Remediation complying with SIA 248 requirements mandates removing the peripheral tiles of the shower, mechanically cleaning the substrate down to a sound base, then installing a new reinforcement band bridged with two-component waterproofing mortar over a minimum width of ten centimetres on either side of the joint.

To document disorders noted on site before work, the site foreman transmits a written notice of defects to site management in accordance with SIA 118 rules. Work remains suspended until official adjustment of recesses or validation of a technical addendum for the transition profile.

Frequently asked questions

Can a ready-to-tile board be cut to adjust to out-of-square walls?

Most rigid foam boards allow limited perimeter dimensional adjustment, generally up to five centimetres per edge, provided sufficient edge thickness is retained for embedding the waterproofing band. Asymmetric cuts nevertheless modify the alignment of diamond points towards the trap. If the masonry walls exhibit excessive out-of-squareness, it is technically preferable to straighten the partitions with waterproof resurfacing mortar prior to installation.

How should the junction between the prefabricated tray and the rest of the room's screed be treated?

The junction constitutes a movement joint subject to differential expansion. The tiler bridges the connection between the tray and the cement screed using an elastic waterproofing band roller-pressed into the under-tile waterproofing mortar. This band ensures water tightness continuity according to SIA 248. On the surface, the tile joint located exactly plumb with this element rupture is sealed using a sanitary neutral silicone elastomer sealant.

What thickness of adhesive mortar should be applied under the prefabricated tray to ensure its stability?

The ready-to-tile tray must rest on a continuous, full bed of adhesive mortar to prevent any bending under users' point loads. Installation is carried out by double gluing with a medium-sized notched trowel, with a crushed residual bed of three to five millimetres. Spot wedging using blobs of adhesive is strictly prohibited as it generates air voids under the board, causing subsequent tile cracking or infiltration.

In which case does on-site shaped waterproofing remain essential on the construction site?

Waterproofing produced on site using a flexible waterproofing mortar or a manually applied mat is required for non-standardised geometries, curved angles or technical recesses with a height of less than sixty-five millimetres. This method is also chosen when the existing drainage does not allow adapting the dedicated trap of a prefabricated system, or during complex renovations requiring continuous floor tiling layout without level breaks with adjoining corridors.

Texts and standards cited

  • norme SIA 248Tiling and slab covering installation: installation prescriptions and under-tile waterproofing
  • norme SIA 118General conditions for the execution of construction work: notice of defects and reservation management

In the same section