Skip to content
Website
🧱 CFC 282Section 5 of 610 chapters

Natural stone: specifics and treatment: the execution reference guide

Intended for team leaders and CFC tile setters, this guide covers the specific constraints of natural stone. Between capillary porosity, chemical sensitivity, reactivity to mixing water and thickness tolerances, the rock tolerates no approximation. Here you will find the execution rules in accordance with SIA 248 standard to install, cut, protect and accept marbles, limestones, granites or sandstones without aesthetic defects or debonding.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

Norme SIA 248

100%

Adhesive transfer rate required under outdoor slabs or heavy loads

Norme SIA 248

pH 7 to 8

Neutrality range of admissible cleaners on marbles and limestones

Norme SIA 248

2 mm

Minimum joint thickness admissible for rectified stone slabs

art. 367 CO

60 days

Legal time limit to report defects in a real estate work after delivery

Scope of application and service limits in natural stone

The installation of a natural stone cladding according to SIA 248 standard requires a higher execution precision than that of a vitrified porcelain stoneware. A heterogeneous mineral material quarried from the earth, the slab features an open porosity, an active capillary network and sometimes metal inclusions sensitive to oxidation. The tile setter's role begins as soon as the dry and stable substrate is inspected, goes through the selection of suitable adhesives and joint mortars, and ends with the delivery of an impregnated work along with its strict maintenance instructions.

Distribution of professional interfaces on natural stone construction sites
Work elementResponsible tradeTile setter's service (CFC 282)
Cement or calcium sulfate screedScreed layer (CFC 281)Visual inspection, flatness measurement and reading of moisture values
Embedded floor heatingHeating engineer (CFC 241)Verification of the heating commissioning report prior to gluing
Liquid waterproofing under tiles (AIF)Tile setter (CFC 282)Installation of mats, corner waterproofing tapes and penetration sleeves
Roof terrace waterproofingWaterproofer (CFC 226)Termination of the setting bed on drainage system above the waterproof assembly
Heavy renovation by crystallizationSpecialized grinding companyEnd-of-construction cleaning with neutral detergent and water-repellent treatment

The rheological and water behavior of a limestone slab or crystalline marble prohibits the use of standard tools or admixtures. An ordinary grey adhesive migrates through white limestone and produces indelible shadows. Stagnant water on an exterior terrace causes frost-susceptible slabs to shatter during the first winter cycle. The success of the work relies on compliance with the mineralogical specificities and dimensional tolerances of each rock.

Logical order of installation steps and section workflow

Handling natural stone requires a sequence of ordered technical operations. Neglecting dry layout planning inevitably leads to a refusal of the work by the client due to unacceptable chromatic disparities. Likewise, applying a joint mortar without prior impregnation exposes the sawn edge to absorption streaks that are impossible to clean without damaging the polished or honed surface finish.

  1. Load diagnosis and preliminary layout planningCheck the load-bearing capacity of the floor against the density of the rock, then lay out the slabs dry on the floor to balance veins and shades before any tile adhesive preparation.
  2. Chemical preparation and bonding without moisture transferIt is imperative to choose a fast-setting white tile adhesive to neutralize the risk of a water film, and apply a temporary protective treatment if the rock is highly absorbent.
  3. Mechanical cutting and edge machiningCut the modules with a water saw equipped with a continuous-rim diamond blade, then chamfer and hone the exposed edges to prevent sharp splinters at the border.
  4. Neutral jointing and operating instructionsMix a special joint mortar without silicone oil bleeding, clean with a dry cloth or wrung-out sponge, and hand over to the client the list of prohibited maintenance products.

The ten chapters of this section detail each critical point: from the prevention of dark shadows under light marble to the secure anchoring of a stair nosing, integrating exterior frost constraints and the contractual duties related to the acceptance of the work.

📘 Chapters in this section 10

Natural stone: characteristics and treatment

Stone staining: porosity, impregnation before grouting and cooking oil

Master water-repellent treatments to permanently block greasy substances before applying mortars.

Natural stone: characteristics and treatment

The veil: light stone, bleeding adhesive, and fast-reacting white adhesive

Eliminate moisture shadows under light marbles using fast-setting white tile adhesives.

Natural stone: characteristics and treatment

Acid attacks: limestone, marble, prohibited products and maintenance instructions

Preserve the polish of carbonate rocks by banning acids in favor of neutral detergents.

Natural stone: characteristics and treatment

Veining: sorting of slabs, dry layout before installation and client approval

Harmonize chromatic variations and obtain formal validation of the layout planning before any gluing.

Natural stone: characteristics and treatment

Weight: thickness, load per square metre, received background and old floor

Validate admissible loads per square meter to secure installation on old floors.

Natural stone: characteristics and treatment

Outdoor stone: frost, de-icing salt, flaking and stones to avoid

Select non-frost-susceptible rocks to withstand freeze-thaw cycles durably.

Natural stone: characteristics and treatment

Cutting stone: wet saw, edge spalling, honing and exposed edge

Achieve clean cuts without chipping and shape perfectly regular honed edges.

Natural stone: characteristics and treatment

Grouting natural stone: compatible mortar, matching colour and joint staining the stone

Mix joint mortars without bleeding to prevent indelible peripheral rings.

Natural stone: characteristics and treatment

Stone stair: nosing, fixing, anti-slip and rocking step

Fix steps and risers with full-coverage bonding to eliminate any risk of tilting.

Natural stone: characteristics and treatment

Handing over stone: maintenance instructions, renewal of impregnation and expectations

Hand over the cleaning protocol and secure the acceptance of the work without subsequent reservations.