Skip to content
Website
🧱 CFC 282Section 4 of 610 chapters

Tiling, setting out, joints and lippage: the execution standard

Installing tiles or natural stone requires absolute geometric precision and strict compliance with the SIA 248 standard. This section guides team leaders, foremen and tilers in execution rules: setting out without blind cuts, controlling flatness and lippage tolerances, sizing movement joints and choosing cement or epoxy mortars. It ensures a durable, safe installation accepted without reservations.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

norme SIA 248

2 mm

Minimum width of an indoor joint for rectified porcelain stoneware

norme SIA 248

1 mm

Maximum allowable lippage between two adjacent rectified tiles

norme SIA 248

40 m²

Maximum area of a panel without a fractioning joint without underfloor heating

norme SIA 248

20 m²

Maximum area of a tiled panel on a heated screed before fractioning

norme SIA 248

2 m

Minimum perpendicular observation distance during visual acceptance inspection

Technical scope and intervention limits

The tiler's work under CFC 282 revolves around the bonded or bedded installation of ceramic coverings and natural stones, both on floors and on interior or exterior walls. This section deals exclusively with geometric setting out, edge treatment, sizing and filling of joints, as well as compliance with surface tolerances prescribed by the SIA 248 standard. It also incorporates operational safety criteria, notably slip resistance and delicate replacement interventions of isolated elements after completion.

  • Screeds and slope formwork (CFC 281): thickness, mechanical strength, drying and measurement of the residual moisture content belong to the screed layer. The tiler checks substrate acceptance without taking test samples themselves.
  • Underfloor heating (CFC 241): thermal adjustment, installation of heating coils and management of the prior heating-up protocol are under the sole responsibility of the heating engineer.
  • Heavy primary waterproofing (CFC 226): bituminous or synthetic waterproofing systems for flat roofs and pedestally-supported terraces fall under the roofer's trade. The tiler exclusively manages waterproofing mats and thin membranes under tiles directly associated with the adhesive bed.
  • Lining partitions (CFC 271): rigidity of reinforced or water-repellent plasterboards and the spacing of studs are the responsibility of the plasterer.
  • Sanitary installations (CFC 250): installation of channel bodies, gullies and piping is incumbent upon the sanitary installer; the tiler ensures the implementation of the waterproofing collar and the watertight perimeter connection.

Management of structural joints requires strict site coordination. A movement joint crossing the structural work or a fractioning joint provided in the screed by the screed layer must never be rigidly bridged by the tiling. The tiler must take up these cuts precisely plumb in their own covering using suitable deformable profiles or elastomeric sealants, in close coordination with site management.

Logical execution progression and reading guide

To ensure installation without defects or costly rework, the installation team must approach the ten chapters of this section in an operational chronological order, starting from spatial planning and ending with acceptance and after-sales service operations.

  1. Geometric planning and preliminary fractioningThe study must begin with setting out [T4-01] in order to centre key pieces and reject cuts greater than half a tile along visible walls. It continues with the mandatory calculation of fractioning joints [T4-04], in order to define the layout of surfaces before spreading the tile adhesive.
  2. Installation and control of surface tolerancesDuring the actual installation, constant monitoring of lippage [T4-02] avoids height offsets under the straightedge. This is accompanied by scrupulous compliance with the minimum joint width [T4-03], dimensioned according to the tile format to absorb dimensional variations and prevent premature cracking.
  3. Edge finishes and void fillingThe finishing phase deals with the mechanical protection of external corners using profiles or mitre cuts [T4-07]. It moves on to the application of cementitious grouting [T4-05] or high-strength chemical sealing using epoxy resin-based products [T4-06], requiring close control of washing times.
  4. Performance control and acceptanceFinal verification incorporates the adhesion and slip-resistance class [T4-08] required for user safety. The construction site concludes with the contradictory acceptance inspection [T4-09] according to art. 367 CO, relying if necessary on the surgical replacement protocol for a damaged tile [T4-10].

📘 Chapters in this section 10

Laying, layout, joints and lippage

Setting out: starting axis, edge cut width and first visible tile

Eliminate wedge cuts right from the threshold to guarantee perfect visual alignment in every room.

Laying, layout, joints and lippage

Lipper: tolerance, straightedge measurement, and the edge that catches the foot

Master level deviations under the straightedge to eliminate sharp edges that injure feet.

Laying, layout, joints and lippage

Joint width: minimum per format, dimensional tolerance and zero-joint installation

Respect the spacings prescribed by the standard to definitively ban zero-joint installation, which is prohibited.

Laying, layout, joints and lippage

Dividing tiling: maximum surface area, peripheral edge and joint profile

Position your movement profiles in the right place to prevent tile lifting and breakage.

Laying, layout, joints and lippage

Joint mortar: class, colour, cleaning and residual haze on the tile

Select the appropriate mortar and succeed at trowelling to eliminate stubborn cement veils.

Laying, layout, joints and lippage

Epoxy grout: cleanability, chemical resistance, and zero-tolerance application

Guarantee absolute chemical waterproofing by mastering strict emulsion and cleaning times for the resin.

Laying, layout, joints and lippage

Edges: finishing profile, forty-five-degree mitre cut and fragile tile edge

Choose between metal profile and mitre cut to durably protect external corners exposed to impacts.

Laying, layout, joints and lippage

Do not slip: slip resistance class per room, barefoot and cleanability

Assign the correct slip-resistance class according to the room's use to secure users without blocking maintenance.

Laying, layout, joints and lippage

Acceptation of the work: inspection distance, lighting, planeness, joints and relevant reservations

Control grazing lighting and formalise floor acceptance to defuse abusive aesthetic disputes.

Laying, layout, joints and lippage

Replacing a tile: removal without breaking adjacent ones, shade batch and reserve

Cut around the joint without chipping neighbouring tiles to replace a damaged element invisibly.