Skip to content
Website
🧱 CFC 274Section 1 of 610 chapters

Guardrails: height, infill and compliance: the execution reference

Intended for workshop managers, foremen and site managers in metalwork, this section brings together the construction requirements essential to passing the acceptance of guardrails and handrails. It details the requirements of the SIA 358 standard, gap geometries, the behaviour of infills and the precise criteria applied by municipal inspectors before the occupancy permit is issued.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

Norme SIA 358

100 cm

Minimum height of a guardrail for a fall of less than 12 metres

Norme SIA 358

110 cm

Mandatory minimum height when the fall height exceeds 12 metres

Norme SIA 358

12 cm

Diameter of the control sphere, which must not pass through any gap

art. 22 OTConst

100 cm

Minimum height of the top rail for a temporary perimeter guardrail

Technical scope of the metalworker and limits of intervention

This guide deals exclusively with building metalwork and light metalwork falling under CFC 274. It covers guardrails for balconies, terraces and access galleries, barriers for interior or external staircases, parapet balustrades and wall-mounted handrails. These elements perform a passive safety function against falls from height without contributing to the bracing or the general structural stability of the building.

To preserve the contractual limits of each trade, several neighbouring works are formally excluded from this technical scope:

  • Steel load-bearing structures, frameworks of suspended balconies, façade posts and steel framing, which fall under metal construction according to CFC 215.
  • Slabs, reinforced concrete brackets and recesses cast on site, under the responsibility of the mason according to CFC 211.1.
  • Guardrails integrated into windows, French windows and monobloc sub-frames, which depend on external joinery according to CFC 221.
  • Anticorrosion treatment by metallisation or powder coating applied in an industrial workshop, attached to CFC 215, metalwork handling only touch-up paint repairs on the construction site.
  • The calculation of the overall mechanical strength of the structural work receiving the anchor plates, which requires the formal involvement of the project's civil engineer.

The metalworker is responsible for the strength of their mechanical or chemical fixings into sound concrete, for the choice of profile sections, for the assembly of the rails and for strict compliance with manufacturing tolerances, so as to avoid any legal risk under art. 229 CP in the event of bodily injury resulting from failure to comply with the rules of the trade.

Methodological progression to master guardrail compliance

The design and installation of a balustrade without reservations require an orderly reading of the constraints. A dimensional error of ten millimetres or an unsuitable baluster arrangement leads the municipal building-control departments to withhold the occupancy permit. The chapters of this guide follow the real chronology of operations, from the workshop drawing to the final inspection of the finished work.

  1. Validating the primary geometry and parapet heightsChapters [Q1-01] and [Q1-05] define the minimum vertical dimensions required by the SIA 358 standard according to the potential fall height, on a horizontal landing as well as on a sloping flight of steps, measured from the finished walkable floor level.
  2. Neutralising the risks of passing through and climbingSheets [Q1-02] and [Q1-03] cover the control sphere gauge, the clear gaps between posts and balusters, the gap under the bottom rail and the provisions preventing the ladder effect for young children.
  3. Securing sensitive materials and configurationsSections [Q1-04], [Q1-08] and [Q1-09] address the residual strength of laminated safety glass, anchoring without piercing the waterproofing on terraces, and the continuous ergonomics of the handrail.
  4. Defending the work against legal and administrative requirementsModules [Q1-06], [Q1-07] and [Q1-10] cover the duty to notify in renovation, clearly separate the permanent guardrail from construction site protection according to art. 22 OTConst, and prepare the self-inspection needed to pass the municipal visit.
Overview of the critical deviations penalised during compliance visits
Inspected elementSIA 358 normative requirementDirect consequence for the occupancy permit
Standard clear heightAt least 100 cm from the finished floorImmediate refusal, raising or adding a rail mandatory
Opening gaugeMust not allow a 12 cm sphere to passBlocking non-conformity, baluster arrangement to be reworked
Climbing zoneNo horizontal foothold between 10 and 65 cmSmooth screens or backing sheets must be installed
Gap between floor and bottom railGap strictly less than 10 cmAcceptance postponed, stop flat bar to be fitted

Rigorous application of these steps ensures full control of rework costs, guarantees the effective safety of users and contractually protects the workshop against the strict requirements of site management.

📘 Chapters in this section 10

Balustrades: height, infill and compliance

Height: the standard minimum, the increased minimum for great heights, and where to measure

Master the exact measuring points to guarantee the regulatory height according to your actual level difference.

Balustrades: height, infill and compliance

Spacing: the control sphere, gaps at floor level and the forgotten gap under the bottom rail

Avoid geometric rework by applying the control sphere to all critical openings.

Balustrades: height, infill and compliance

The ladder effect: climbable horizontal rails, the zone concerned and refusal of the permit

Neutralise the climbing risks of horizontal balusters before the inspector rejects the completed work.

Balustrades: height, infill and compliance

Glass infill: laminated glass mandatory, post-breakage performance and fixing

Select the right laminated glazing to maintain mechanical restraint even after complete breakage.

Balustrades: height, infill and compliance

On a staircase: height measured at the stair nosing, handrail and continuity

Set out the slopes and stair headroom heights without losing alignment on the stair nosings.

Balustrades: height, infill and compliance

Non-compliant existing structures: upgrade obligation, triggering works and written notice

Draft your written duty to notify when facing old railings without incurring your civil liability.

Balustrades: height, infill and compliance

Temporary and permanent: two structures, two sets of rules, and the confusion that proves costly

Distinguish construction site safety rules from civil standards to protect your profit margins.

Balustrades: height, infill and compliance

Accessible roof: guardrail or parapet, fixing without piercing the waterproofing

Fix your balustrades on roofs without damaging the waterproofing system or weakening the insulated upstands.

Balustrades: height, infill and compliance

The handrail: grippable section, clearance from the wall, continuity and returns

Manufacture continuous, graspable handrails meeting the ergonomic criteria of the standard.

Balustrades: height, infill and compliance

The municipal inspection: what is measured, what blocks approval, and how to prepare

Prepare your self-inspection file to pass the building-control visit without reservations.