Skip to content
Website
🧱 CFC 282Cutting, silica, claims and tiler safetyChapter 10 of 10 in the section

Expert assessment: removal of a tile, measured coverage rate and verdict

When faced with a dispute concerning hollow-sounding or cracked tiles, joint expert assessment relies on a decisive physical finding: the removal of an element and the direct measurement of adhesive mortar transfer. This chapter details the method for managing this operation, calculating the wetting rate precisely and ensuring the preservation of the removed samples.

Key takeaways

  • The joint removal of a tile immediately seals the physical evidence of the installation defect.
  • Standard SIA 118 governs the duties of the parties during the notification of defects.
  • The transfer rate measured under the tile determines the compliance of the buttering-floating method.
  • The chain of custody for samples guarantees that the removed pieces are admissible in court during disputes.

Joint removal on site and immediate observation of the interface

On a construction site subject to a claim for debonding or cracking, joint expert assessment avoids visual conjecture by isolating a control area. When the client invokes a defect in accordance with the acceptance and warranty rules defined by standard SIA 118, the formal summoning of all stakeholders remains an absolute prerequisite. The tiler, the site management and the adhesive manufacturer must be present around the incriminated tile before the first blow of the chisel. Unilaterally opening up a finish destroys the legal value of the finding, as the contractor can always argue that the removal was forced or carried out outside the disputed areas.

  1. Delineation of the area by core drilling or diamond discCut around the complete perimeter grout line using an angle grinder with local dust extraction to cut through the grouting mortar without transmitting destructive vibrations to adjacent tiles.
  2. Mechanical lifting without point impactInsert a wide blade or mechanical suction cups to exert perpendicular traction. The objective is to extract the entire tile without tearing the underlying screed or fracturing the body of the tile.
  3. In-situ photography before handlingTake immediate macroscopic photographs of the back of the tile and the floor impression, with a millimetre scale and visible date, before ambient air alters the dust or residual moisture.

As soon as the element detaches, visual inspection instantly qualifies the mode of failure. If the adhesive mortar remains entirely bonded to the substrate with intact, unflattened comb ridges, the tiler's liability is directly engaged: the open time was exceeded or pressing down by beating never took place. If the adhesive adheres perfectly to the back of the tile but tears the surface skin of the screed, the cause shifts to the substrate. The expert needs no theoretical interpretation: the morphology of the ridges proves whether the installation work was carried out in a professional manner.

Calculating the coverage rate and locking the chain of evidence

The measurement of the coverage rate, or effective contact surface between the adhesive mortar and the underside of the ceramic, constitutes the technical core of the expert report. In standard residential areas, professional rules require a transfer surface of at least 80 percent under the tile, whereas exterior terraces, industrial premises and swimming pool surrounds require a rate of 100 percent, with no air voids permissible. To determine this value without dispute, the expert applies a calibrated transparent grid over the rear surface of the removed tile and calculates the ratio between the effective transfer areas and the total surface.

Standard contact requirements and associated installation methods
Destination of the structureMinimum contact rateRequired pressing method
Living rooms and interior bedrooms80% of the surfaceSingle gluing with careful beating
Bathrooms and showers90% of the surfaceSystematic double gluing
Exterior terraces and balconies100% (zero air voids)Cross double gluing or fluid adhesive
Commercial premises under heavy traffic100% of the surfaceDouble gluing with appropriate notches

The result of this measurement dictates the outcome of the claim. If the back of a large-format porcelain stoneware tile exhibits still-ridged lines covering only 50 percent of the surface, the insufficient transfer proves the absence of double gluing or insufficient beating, ruining the mechanical resistance against operational loads. The artisan cannot then invoke either thermal expansion or building movements to justify the failure.

  1. Indelible marking of the pieceInscribe the removal number, date, cardinal orientation and concerned room on the back of the tile using a moisture-resistant marker.
  2. Joint signature of the reportDraft a sampling document on site signed by the tiler and the expert, recording the measured rate, the thickness of the adhesive bed and any reservations.
  3. Packaging under sealPlace the element in a rigid packaging closed with a numbered tape to prevent any substitution before possible transport to an analytical laboratory.

Qualification of the defect according to standard SIA 118 and scope of the verdict

Once the tile is extracted and its underside photographed, the technical finding shifts into the contractual field. According to standard SIA 118, a work is deemed defective when it lacks the promised qualities or those that the client could legitimately expect according to professional practice. A hollow sound detected by an acoustic mallet is merely an indicator of debonding or residual void; uncovering the adhesive bed provides irrefutable physical proof. The judicial or insurance expert does not rule on impressions, but on a geometric ratio between the effective adhesion surface and the total surface of the tile. This direct calculation seals the materiality of the breach of Swiss professional guidelines for bonded tile installation.

The finding of a filling deficit entails direct consequences under the warranty regime provided for by standard SIA 118 or the Code of Obligations. The client primarily has the right to demand the repair of the work at the contractor's expense. In tiling, local repair is almost always refused if the incriminated application method was systematic: unilateral combing without flattening revealed on two control tiles sampled from a surface of fifty square metres demonstrates a flawed methodology across the entire batch. The contractor cannot invoke disproportionate costs when the durability of the work is threatened by the risk of tile breakage under concentrated loads or generalized debonding in the event of thermal stresses.

Defensive strategy of the company: self-monitoring and evidentiary chain

Faced with a joint expert assessment, verbal disputes or declarations of intent have no probative value. To protect the company against a unilateral requalification of the damage, the site manager and the team leader must organise traceability from the very first square metre laid. If a detached tile exhibits unflattened ridges, the presumption of technical fault by the layer is almost absolute. The only legal and technical defense relies on providing documented evidence demonstrating that the installation complied with the beating protocol and the technical data sheets of the adhesive mortars used on site.

Joint analysis of interfaces during sampling
Observed failure faciesFinding on the adhesive bedProbable technical originConsequence on liability
Intact and hard ridgesNo contact with the ceramicsOmission of double gluing or exceeding open timeExecution fault attributed exclusively to the tiler
Tear at the back of the tileSmooth adhesive film without transferUncleaned firing dust or tile too hotFailure to prepare the material by the layer
Cohesive failure in the adhesiveMortar torn into two thicknessesShear due to expansion or deformation of the substratePossible questioning of the screed or movement joints
Debonding under the waterproofing matAdhesive bonded to both the tiling and the matAbsence of primer or powdery substrate under the waterproofingInvestigation required into the preparation of the raw substrate
  1. Systematic verification by cost-free samplingLift one tile every ten slabs immediately after beating to measure the actual transfer rate and adapt the choice of the comb.
  2. Time-stamped photograph of the crushing interfaceRecord the image of the glued back in the site logbook with a graduated gauge attesting to the total flattening of the adhesive ridges.
  3. Control of batches and ambient conditionsArchive batch numbers, ambient temperature and compliance with the usage limit of the spread adhesive.

On the day of the joint sampling, the representative of the tiling company must countersign the report while recording their own technical remarks. They immediately document the condition of the back of the tile, note the temperature of the room and demand that the sample be sealed on site in rigid packaging with tamper-evident labelling. A break in the chain of custody of the removed element makes any subsequent laboratory examination easily contestable during the judicial phase.

Remedies and management of disagreement after finding an adhesive deficit

When the sampled tile reveals a ribbed back, intact adhesive ridges without flattening and a contact surface lower than the required requirements, the visual finding immediately weakens the layer's position. The judicial or private expert records the measured percentages, air voids and the absence of mortar transfer. The contractor must not contest the physical evidence in the heat of the moment: their mission on site consists in having all the physical conditions of the sampling accurately recorded in the joint report, before the sample leaves the site sealed.

If the verdict is contested, the technical argumentation must be based on measurable and documented facts. The site manager records their direct reservations on the document: contested representativeness of the sampled area, presence of a heating element modifying the local setting, or prior deformation of the screed not attributable to the tiling. If the client invokes a major defect according to the rules of standard SIA 118 relating to complaints and the contractor's rights, the latter may demand the opening of a second joint sounding on a sound control area to verify whether the deficit is systematic or localized.

  • Demand the immediate entry in the report of your observations on the flatness of the substrate under the residual adhesive and the condition of the combs used.
  • Photograph the extracted tile from three angles with a calibrated ruler and verify the exact reference of the seal number affixed to the transport bag.
  • Propose a repair solution circumscribed to hollow-sounding tiles rather than general removal, relying on acoustic survey protocols.
  • Forward the entire joint file and site self-monitoring sheets to the company's professional civil liability insurance.

Frequently asked questions

Can the removal of a sealed tile be refused during an expert assessment?

No. The client may have the work examined in the event of a technical dispute. Refusing the opening prevents the administration of proof and places the tiler in an unfavourable position. Conversely, the contractor must demand that the removal be joint, that it be carried out using a non-destructive method for neighbouring elements and that each step be recorded on the site report signed by the parties.

Who bears the financial cost of removal and reinstatement?

The costs of sampling and immediate repair are advanced by the party requesting the assessment or defined by the assessment contract. If the inspection highlights an installation not complying with recognized rules of technique, the contractor bears the cost of repairs and tile replacement under their works warranty according to the general principles of standard SIA 118.

How to contest a transfer rate calculation deemed too severe?

The contestation relies on the measurement protocol. If the expert estimated the surface by eye without a millimetre grid or digital survey, the contractor formulates a formal reservation on the report. They can demand the digitalisation of the back of the sealed tile and image analysis calculation by a neutral laboratory in order to obtain an incontestable and opposable surface percentage.

What to do if the tile breaks into several pieces during extraction?

The expert and the contractor must retrieve all fragments without scraping off the adhesive mortar. The pieces are reassembled flat on a clean surface to evaluate the adhesive bed. The report mentions that mechanical breakage may have altered the adhesion interface. The shattered sample is packed under a collective seal and the parties agree if necessary on a second sounding on a contiguous element.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work, governing acceptance, notification of defects and the exercise of warranty rights.

In the same section