Key takeaways
- Scrupulously respecting the water volume guarantees mechanical strength and prevents detrimental shrinkage.
- A maturation time of three to five minutes allows the complete dissolution of the polymer resins.
- Remixing an adhesive that is starting to set breaks the crystalline bonds and ruins the final adhesion.
- Throwing away fifty francs' worth of expired adhesive costs infinitely less than a complete rework under warranty.
Preparation of adhesive mortar and the obligation of chemical maturation
On a Swiss construction site subject to standard SIA 248, the preparation of the bedding layer begins with rigorous mixing of class C2 deformable adhesive mortars. The manufacturer's technical data sheet indicates a strict water range, generally between 22% and 26% of the powder weight, i.e., approximately 5.5 to 6.5 litres of clean water for a standard 25 kg bag. Mixing is never done by eye or with a water hose: using a graduated bucket is the only accepted method to guarantee the prescribed consistency and prevent a sharp drop in mechanical strength.
- Adding the componentsPour all the clean, temperate water into a clean mixing tub first, then gradually incorporate the dry powder to limit the formation of lumps against the sides.
- First mechanical mixingMix using an electric slow-speed mixer, regulated between 400 and 500 revolutions per minute, for a full two to three minutes, until a perfectly homogeneous paste free of lumps is obtained.
- Mandatory maturationAllow the mix to rest without any agitation for three to five full minutes to allow the cellulosic additives to go into solution and the synthetic resins to disperse.
- Short final remixingAgitate the mortar again for 30 to 45 seconds without adding a single drop of water, in order to fluidify the paste before spreading it with a notched trowel.
Excessive addition of water to fluidify the mix modifies the water/cement ratio and creates excessive capillary porosity at the core of the dried adhesive bed. This results in significant volumetric shrinkage during curing, which generates shear stresses beneath the tiles and encourages the formation of hollow pockets under the floor covering.
Setting adhesive must be thrown away: the ban on remixing and the cost of defects
Every adhesive mortar has a practical working life, commonly referred to as pot life, which ranges between two and four hours at an ambient temperature of 20 °C. As soon as the atmosphere warms up on the construction site or draughts sweep through the rooms, the exothermic setting reactions accelerate. The paste then begins to stiffen at the bottom of the tub and forms a characteristic surface crust.
| Operational criterion | Immediate disposal of the tub | Remixing with added water |
|---|---|---|
| Crystalline structure | Preserves subsequent batches with a fresh mix | Crushed crystalline network, complete absence of internal cohesion |
| Residual adhesion | Complies with the requirements of standard SIA 248 | Drop in adhesion below the critical threshold of 0.5 N/mm² |
| Behavior under tiling | Complete wetting and optimal transfer to the back | Hollow sound underfoot, rapid debonding under traffic |
| Financial consequence | Direct loss of a bag of adhesive (approximately 30 to 45 CHF) | Removal, scraping, repurchase of tiles and remedial labor |
From an economic perspective, the calculation for a site foreman or qualified tiler is immediate. Trying to save a few dozen francs on binder by artificially extending the life of a tired tub exposes the company to large-scale defects. When the tiling begins to sound hollow a few weeks after the acceptance of the work, the Code of Obligations requires remediation at the sole expense of the contractor.
Remediation then involves the mechanical hacking out of the loose tiles, removal of rubble, careful sanding of the original screed to eliminate degraded mortar, as well as the supply of new ceramic slabs identical to the original firing batch. Repairing a single twenty-square-metre room quickly generates labor and material costs that exceed fifty to one hundred times the price of the bag of adhesive that a worker hesitated to throw away. The best practice rule is crystal clear: adhesive that has started to set goes straight into the skip.
Instrumented mixing protocol and hydration kinetics in accordance with standard SIA 248
The application of deformable or improved adhesive mortars tolerates no approximation in batching on site. Standard SIA 248 governs the installation of ceramic coverings and mandates strict compliance with manufacturers' technical data sheets. An adhesive is a complex chemical system combining Portland cement, redispersible polymer resins, cellulose ethers and set regulators. Achieving the promised mechanical strengths requires dosing water to the nearest decilitre using a clean graduated container. Pouring water by eye immediately unbalances the water/cement ratio: a 10% excess of water reduces the tensile strength of the bedding layer by a third and increases hydraulic shrinkage, creating destructive shear stresses beneath large formats.
- Dosing clean waterPour the prescribed volume of water into the clean container, generally between 22% and 26% of the powder weight. Water must always precede the powder to prevent unmixed dry material from agglomerating at the bottom of the bucket.
- Dusting and first mixingIntroduce the powder gradually under mechanical agitation at low speed, between 400 and 600 revolutions per minute. Continue mixing for two to three minutes to dissolve lumps and obtain a homogeneous paste.
- Chemical maturation at restAllow the mix to rest undisturbed. This phase allows the polymers and cellulose ethers to swell via aqueous solvation, guaranteeing wetting power and slip resistance.
- Activation flash re-mixingAgitate the mix for 30 to 45 seconds without adding water. This step breaks the rest thixotropy and gives the mortar its final workability for application with a notched trowel.
| Altered parameter | Physicochemical phenomenon | Consequence on the work |
|---|---|---|
| Water overdose (> 5%) | Increased capillary porosity and dilution of hydrated silicates | Drop in tensile adhesion, sagging of ridges and high shrinkage |
| Water underdose (> 5%) | Incomplete cement hydration and excessive viscosity | Deficient tile wetting, reduction of open time and debonding |
| Excessive speed (> 800 rpm) | Mechanical air entrapment and destructuring resin emulsion | Lower density of the bedding layer and weakening of internal cohesion |
| Omission of maturation | Undissolved polymers and inactive water retention agents | Tile slippage, heterogeneous setting and loss of initial adhesion |
Mechanics of early shear: why stiffened mix must be discarded without appeal
During the practical working life (PWL), which usually ranges between two and four hours at 20 °C, exothermic hydration reactions begin. Microscopic crystalline needles of calcium silicate hydrates and ettringite germinate in the paste, linking the quartz grains together to form the cement matrix. When the adhesive begins to stiffen in the bucket due to time or draughts, this early crystallization organizes and densifies. Attempting to mechanically remix setting adhesive irreversibly destroys this nascent mineral network. The sheared and crushed micro-crystals no longer form cohesive bonds: the mortar definitively loses its adhesive power and its shear strength beneath the tiling.
On Swiss construction sites, economic and technical arbitration leaves no room for compromise. Standard SIA 248 excludes any reuse of mortar that has started to set. Throwing away a remaining fifteen-kilo mix represents a loss of a few Swiss francs of material. In contrast, installing tiles on remixed adhesive generates massive defects: hollow-sounding tiles, joint cracking and debonding under operational load. The cost of remediation — removal, sanding of the substrate, purchasing new ceramics and site downtime — exceeds the value of the discarded product by several thousand francs.
Remedial protocol after a mixing error and financial arbitration
On site, discovering adhesive applied after stiffening or remixed with water inevitably results in a structural adhesion defect. When the mix has started to set in the bucket, polymer chains and cement microcrystals are irreversibly damaged by any secondary mixing. If installation continued nonetheless due to inadvertence or negligence, symptoms appear very quickly during execution checks: hollow sounds under the mallet handle, slabs lifting effortlessly during cleaning or outright debonding when cutting expansion joints. At this stage, masking the problem or hoping for hold from the grout joints constitutes a major professional error.
- Immediate removal and salvaging of tilesAs soon as the defect is identified, promptly remove the ceramic elements laid on dead adhesive. If removal occurs before complete setting, the tiles can be washed with clean water on their bonding side for reuse, thus avoiding costly repurchasing.
- Complete mechanical cleaning of the substrateChisel and scrape away all vitiated adhesive mortar down to the raw mineral substrate. Re-bonding over altered or powdery adhesive is prohibited: the interface must regain the initial cohesion of the screed or floor render before any new operation.
- Dust removal and resumption of compliant bondingMeticulously vacuum residual dust in accordance with the cleanliness requirements of standard SIA 248. Prepare a new mix by measuring water with a graduated bucket, respect the three-to-five-minute maturation time, and apply using the appropriate notched trowel.
The site manager must demand that tilers automatically discard any opened tub whose practical working life has been exceeded. This rigor guarantees the durability of the work and protects the company from destructive expert assessments that harm its reputation.
Frequently asked questions
How to identify an adhesive mortar that has been remixed on site?
An adhesive remixed with water has a glossy yet lumpy appearance and loses its thixotropic properties: the ridges formed by the notched spreader collapse immediately instead of remaining firm. To the touch, the initial tack has disappeared and a matte film forms on the surface. Once dry, this mortar crumbles effortlessly under a blade, proving that the crystalline hydration structure was cleanly broken by the second mixing.
Can an adhesive that is starting to set be reactivated by adding fresh powder?
No, this empirical method is formally banned from any tiling site. Remixing the paste by adding powder and water generates a completely unbalanced mix where destroyed hydrate residues sit alongside undispersed cement grains. Mechanical adhesion and internal cohesion collapse below the values prescribed by standard SIA 248. The entire bucket must be sent to the skip without exception.
Why is the three-to-five-minute maturation time mandatory before spreading?
The resting time allows the complete dissolution of the polymer resins and the activation of the cellulose ethers contained in the dry formula. Without this chemical maturation, the mix remains heterogeneous, exhibits microscopic lumps and dries out far too quickly upon contact with air or the substrate. If the mix has just been prepared, simply let it rest and then give it a brief mechanical re-agitation of a few seconds.
What is the procedure to follow if installed tiles sound hollow during inspection?
Tiles sounding hollow indicate a mortar adhesion defect. In accordance with standard SIA 118, the contractor must correct the defect at their own expense. The only durable technical measure consists of removing the affected tiles, completely chiseling out the defective adhesive down to the sound original substrate, and then re-bonding with freshly and rigorously prepared mortar. Attempting to inject resin grouts under the slabs remains a makeshift fix with no guarantee of durability.
Texts and standards cited
- SIA 248Tiled and mosaic bonded floor coverings: installation conditions and preparation
- SIA 118General conditions for the execution of construction works: remediation of defects at the contractor's expense
