Key takeaways
- A synthetic dome never supports the weight of a worker, even when fresh from the factory.
- An exhaustive identification of vents and rooflights is mandatory before any access to a flat roof.
- Installing a fall-arrest mesh grid beneath the upstand constitutes the benchmark permanent collective protection.
- Openings without compliant protection must receive securely fixed decking or a rigid perimeter edge protection.
The dome is not a floor: mechanics of failure and prior identification
On a flat roof, point rooflights and overhead lighting domes represent one of the deadliest traps for the waterproofer. The translucency or rigid appearance of polymethyl methacrylate (PMMA) or polycarbonate glazing creates a false sense of security. Yet, no standard overhead daylighting element is designed to withstand a dynamic point load. Even when brand new, a dome undergoes critical deflection under the impact of a footstep or a loss of balance. Over the years, ultraviolet radiation, thermal fluctuations, and aggressive cleaning degrade plasticisers, making the shell extremely brittle. Failure then occurs without prior deformation or any audible warning.
- Document review and aerial viewConsult working drawings or photographic surveys before going up onto the roof to draw up an accurate inventory of upstands and smoke and heat exhaust rooflights.
- Visual sweep upon reaching roof accessIdentify every singular detail before moving any equipment. If the roof deck is snow-covered, prohibit foot traffic until the exact outline of the domes has been physically marked out.
- Visual inspection of upstands and markingsExamine the condition of frames, the height of waterproofing upstands, and the possible presence of a certification label indicating fall resistance.
- Demarcation of the working areaAs long as resistance has not been proven, establish an exclusion perimeter of at least two metres around every translucent element lacking a grid.
Identification is not limited to looking at the top surface. It entails checking the nature of the upstand, whether made of reinforced polyester, folded steel sheet, or timber. A cracked or poorly anchored upstand on the load-bearing element can topple under lateral thrust during bituminous or synthetic waterproofing work. Every rooflight must be presumed fragile until a technical certificate or a physical device formally proves its resistance to falling through.
Temporary collective protections and permanent under-dome devices
Openings in floors that present a fall risk must be provided with perimeter edge protection or a securely fixed, break-resistant cover.
art. 25 OTConst
The application of art. 25 OTConst imposes a strict hierarchy on the construction site. During refurbishment or maintenance work on a flat roof, leaving a dome unprotected directly exposes personnel to a fall of several metres into the internal void. Two complementary strategies apply: temporary protection during the construction site phase and the integration of a permanent device beneath the dome, ensuring the future safety of the building.
| Device | Installation | Advantages | Points of attention |
|---|---|---|---|
| Metal grid beneath upstand | Direct mechanical fixing into the trimmer or upstand prior to fitting the dome. | Permanent protection, invisible from the outside, unalterable. | Must be dimensioned according to recognised technical standards without impeding smoke flow. |
| External hail guard grid | Fitted over the dome onto the fixed outer frame. | Fast installation on existing fixtures without opening the building interior. | Check for dirt accumulation under the mesh and verify dynamic impact resistance. |
| Freestanding perimeter edge protection | Rigid frame enclosing the rooflight with ballasted rails and toeboards. | No penetration of the waterproofing system, maintains technical access. | Large footprint on narrow roofs; wind load capacity must be substantiated. |
| Temporary timber covering | Close-boarded decking made of wood-based panels, mechanically secured against slipping. | Immediate construction site solution during glazing replacement. | Securing is mandatory to prevent displacement by wind or accidental thrust. |
For waterproofers, best practice consists of systematically installing a hot-dip galvanised steel fall-arrest mesh grid as soon as the upstand is set in place. This wire mesh remains firmly anchored to the load-bearing structure even if the plastic dome is removed, burnt, or destroyed during an incident. The mesh size must prevent a human body from passing through while preserving the aerodynamic coefficient required for smoke and heat exhaust ventilators.
When a waterproofer works on an existing building whose domes are not equipped with grids, they are under a professional obligation to record this deficiency. Before unrolling waterproofing sheets or welding upstands, the team installs bolted rigid decking or temporary raised mesh covers. No operative must work backwards near an unprotected dome. Definitive protection using integrated grids must systematically be proposed to the building owner to ensure safe future access for maintenance teams.
Technical integration of mesh grids and permanent securing on upstands
On a flat roof, whether a traditional warm roof with elastomeric bitumen membrane or a synthetic single-ply system, overhead rooflights and smoke vents represent the most vulnerable singular details. Both acrylic glass and polycarbonate lose their structural elasticity under the effect of ultraviolet radiation and freeze-thaw cycles. Even in brand-new condition, a thermoformed dome or double-skinned rooflight lacks the mechanical strength required to absorb the dynamic impact of a worker's weight or a bundle of waterproofing rolls placed on it by mistake. Rupture is instantaneous, without warning or visible prior deformation. For the waterproofer executing perimeter thermal insulation and flashing the upstands, the risk of punching through and falling into the building interior is permanent. The installation of underlying mechanical protection must prevent anyone from falling through, regardless of the presence or condition of the top cover.
Definitive protection relies on structural elements mechanically fixed to the load-bearing reinforced concrete trimmer, glulam timber, or the steel roof frame. Hot-dip galvanised steel fall-arrest mesh grids are installed directly inside the upstand kerb, as close as possible to the underside of the dome, so as not to impede airflow or the deployment of actuators on smoke and heat exhaust ventilators. Fixing permits no makeshift solutions: substrate-appropriate anchor screws or certified expansion bolts must be used, positioned according to the centre-to-centre spacings specified by the manufacturer of the system. This system remains in place throughout the life of the structure. It permits future waterproofing maintenance operations, regular cleaning of glazing, or subsequent dome replacement without having to erect temporary collective protection inside the premises below.
| Safety device | Location and fixing | Behaviour and operating phase |
|---|---|---|
| Internal metal mesh grid beneath upstand | Fixed via angle brackets screwed or anchored into the structural trimmer | Permanent protection active during waterproofing refurbishment and normal operation |
| Bar frame integrated into opening sash | Factory-welded or bolted to the subframe of the rooflight | Provides fall arrest retention even when the dome is in the open ventilation position |
| External add-on grid fitted over dome | Clipped or secured to the outer rebate of the upstand | Temporary or permanent protection against falls and hail, vulnerable to tool impacts |
Methodical identification and management of fragile zones before site opening
Before bringing any hoisting equipment, blowtorch, or thermal stripper onto an existing flat roof, the site foreman must carry out an exhaustive identification of vents, rooflights, and daylight openings. The intervention begins with a critical review of roof plans and as-built drawings, followed by a complete visual inspection of the substrate. Ballasted gravel roofs, extensive green roofs, and inverted roof systems create deceptive configurations: the visible height of upstands is often reduced by the thickness of the growing medium or heavy surfacing. In winter, an accumulation of wind-blown snow levels the surface and entirely conceals low-profile domes or flush translucent panels, creating traps without visible demarcation for waterproofers moving with loads.
The federal legal framework dictates absolute rigour on this matter. Art. 25 OTConst provides that openings in floors that present a fall risk must be provided with perimeter edge protection or a securely fixed, break-resistant cover. This requirement directly applies to the waterproofer whenever a rooflight lacks an integrated grid or when its dome is removed to refurbish the waterproofing upstands.
- Document verification and prior inspectionCollect roof plans and inspect the condition of kerbs, domes, and any presence of certified grids beneath overhead openings.
- Approach demarcation and temporary protectionInstall temporary edge protection or securely fixed load-distribution boards over every upstand not fitted with a sturdy fall-arrest mesh grid.
- Execution of waterproofing upstandsWeld reinforcing angle strips and upstand membranes onto the upstand walls without ever leaning mechanically on the dome or frame.
- Conformity check of the completed workVerify that the permanent grid is securely fastened and that the rooflight closes properly before handing over the works to the client.
Managing a safety deficiency or dome breakage on a flat roof
On a flat roof, the failure of a rooflight or the discovery of an upstand lacking a fall-arrest system requires an immediate response from the site foreman. According to art. 25 OTConst, openings in floors that present a fall risk must be provided with perimeter edge protection or a securely fixed, break-resistant cover. If synthetic glazing shatters without anyone falling, the area must be cordoned off immediately. No operative may remain near the trimmer opening without being tethered to a certified anchor point.
- Emergency securing of the roof openingPlace rigid load-distribution decking extending at least 20 cm beyond the upstand kerb, mechanically secured against sliding or wind uplift, or erect temporary ballasted freestanding perimeter edge protection.
- Visual inspection and barricading from belowAccess the internal space beneath the rooflight to check for falling fragments of acrylic glass or polycarbonate, erect barriers at ground level to prohibit access beneath the trimmer, and clean up debris.
- Site report and formal notificationRecord the incident with a photographic report specifying the condition of the frame, the lack of permanent protection under the dome, and the age of the glazing, then submit the formal notice of defect to site management.
- Installation of permanent protectionProhibit returning the rooflight to definitive service without fitting a compliant metal fall-arrest mesh grid to the fixed frame or installing a barred extension securely anchored into the concrete or timber structure.
A waterproofer who discovers domes lacking permanent protection during refurbishment must notify the client in writing. Supplying and fitting integrated grids into upstands is the only durable technical response to ensure safety during future roof maintenance.
Frequently asked questions
Does a new multi-wall polycarbonate dome eliminate the need to install a safety mesh grid?
No. Even when brand new, acrylic glazing or a polycarbonate dome offers no reliable resistance to foot traffic or the dynamic impact of a tripping worker. Ultraviolet rays and weather exposure rapidly degrade the mechanical resilience of polymers. The waterproofer must demand or install a metal fall-arrest mesh grid integral with the upstand, secured directly beneath the upstand or under the fixed frame, to provide permanent collective protection against falling through.
How should rooflight identification be organised during a pre-work inspection under snow?
A layer of snow completely conceals the profile of low upstands or creates an extremely dangerous, uniform false floor. Roof access is strictly prohibited until the exact outline of all roof penetrations has been marked out. The site manager reviews the roof working drawings to identify opening locations. Before any waterproofing work begins, the team erects vertical marker poles or edge protection to demarcate zones presenting a risk of collapse.
What must be done immediately if a dome cracks under a worker's foot without collapsing?
The worker must step away from the upstand immediately, backing away cautiously onto the solid roof. The zone is immediately evacuated and cordoned off at least two metres from the kerb. Covering the cracked glazing with a flexible tarpaulin alone is strictly prohibited, as this would hide the hazard from other operatives. A heavy-duty rigid timber panel must be installed on the opening without delay and mechanically secured.
Who is responsible for installing the permanent fall-arrest mesh grid during a complete roof renovation?
Site management and the client must include this system in the order. If the tender specification does not provide for permanent protection on retained rooflights, the CFC 226 waterproofer has a professional duty to report the danger in writing. They formally propose supplying certified metal grids suited to the existing upstands to ensure building compliance prior to acceptance of the waterproofing layers.
Texts and standards cited
- OTConst art. 25openings in floors: those presenting a fall risk must be provided with perimeter edge protection or a securely fixed, break-resistant cover
- CP art. 229breach of the recognised rules of construction: whoever, in directing or executing a construction or demolition project, intentionally breaches the rules of the trade and knowingly endangers the life or physical integrity of persons shall be liable to a custodial sentence not exceeding five years or a monetary penalty; in cases of negligence, up to three years or a monetary penalty
