Skip to content
Website
🧱 CFC 226Membranes: bitumen, synthetic, laying and jointingChapter 1 of 10 in the section

Elastomeric bitumen or synthetic membrane: what decides the choice

This chapter provides the technical criteria for deciding objectively between elastomeric bitumen and synthetic membranes. You will learn to assess chemical compatibility with insulation or substrate, anticipate fixing methods according to wind loads, and integrate installation constraints, from open-flame work to hot-air welding.

Key takeaways

  • The choice of build-up depends on the substrate, mechanical loads and thermal constraints of the project.
  • Two-layer bituminous systems provide enhanced safety thanks to the redundancy of their two torch-welded layers.
  • Single-ply synthetic membrane lightens the build-up but demands rigorous precision on every welded seam.
  • Standard SIA 271 governs minimum falls, overlaps and mandatory chemical compatibilities.

Two opposing construction principles: bitumen redundancy versus synthetic lightness

The choice between elastomeric bitumen waterproofing and a single-ply synthetic membrane determines the entire design of a flat roof. According to standard SIA 271, the proofer must analyse the permissible load on the load-bearing structure, the future use of the structure and accessibility for maintenance. Bituminous waterproofing is traditionally executed as a two-layer system. It implements a first membrane bonded or torched to the substrate or thermal insulation, then a second crossed or staggered layer, with heat-welded overlaps using a propane gas torch. This layering provides high intrinsic safety: a localised defect or micro-perforation in the top sheet is immediately neutralised by the continuous bituminous underlayer.

Conversely, synthetic systems rely on the principle of the single-ply synthetic membrane. Produced from sheets of plasticised polyvinyl chloride, thermoplastic polyolefins or synthetic elastomer, they feature a very low mass per unit area compared to the roughly eight to ten kilograms per square metre of a two-layer bituminous build-up. This lightness makes it the preferred system on profiled steel decking or lightweight timber frames where load reserve is limited. On the other hand, single-ply tolerates no workmanship compromises. Any failure on a seam or a through-mechanical puncture causes a direct water path into the insulation build-up.

Technical comparison between two-layer elastomeric bitumen and single-ply synthetic membrane
Evaluation criterionTwo-layer bituminous systemSingle-ply synthetic membrane
Average total thickness7 to 10 mm1.5 to 2.0 mm
Self-weight of system8 to 11 kg/m²1.8 to 2.8 kg/m²
Jointing methodDirect flame or hot bitumenAutomated or manual hot air
Puncture resistanceVery high (polyester/glass reinforcements)Moderate (sensitive to sharp edges)
Preferred fieldInverted roofs, car parks, terracesIndustrial sheds, lightweight roofs

Chemical compatibility, wind behaviour and installation thermal constraints

Compatibility with the substrate and the underlying thermal insulation often dictates the technical exclusion of a product family. Rigid expanded or extruded polystyrene insulations react directly on contact with certain materials. Installing a plasticised PVC membrane systematically requires the interposition of a polypropylene or glass fibre separation fleece to prevent plasticiser migration, which would make the sheet brittle. Likewise, the direct flame of the torch is prohibited on bare combustible insulation: the two-layer build-up then requires a cold self-adhesive or mechanically fixed first layer to protect the insulation from fire.

Behaviour under wind uplift loads, calculated according to Swiss codes of practice, influences the fixing method. Synthetic membranes lend themselves ideally to mechanical fastening in the overlaps, calculated per square metre with distribution plates and screws adapted to the metal, concrete or timber substrate. In elastomeric bitumen, bonding is generally achieved through full or partial adhesion using a hot- or cold-applied primer. On roofs with zero fall or a fall below 1.5%, standard SIA 271 sets increased waterproofing requirements that favour the thickness and strength of a heavy bituminous build-up.

  1. Verification of physical incompatibilitiesCheck the nature of the insulation. Provide a separation layer between PVC and residual bitumen or polystyrene.
  2. Choice of jointing energyBanish flame on combustible substrates or high fire-risk areas. Prefer hot-air torches or self-adhesive systems.
  3. Inspection of upstands and detailsAdapt roof projections and penetrations: internal and external corners require preformed pieces suited to the selected material.

Installation: open-flame work versus hot-air welding

On the flat roof, the choice of build-up determines the proofer's tooling, work rates and immediate risk management. Installing a two-layer bituminous system relies primarily on propane gas torches or hot bitumen. The operator heats the underside of the sheet until the elastomeric bitumen (SBS) liquefies, creating a continuous 5 to 10 mm bead that confirms continuous bonding and joint bridging. This technique demands high dexterity to avoid burning the non-woven polyester reinforcement or the glass mat, while guaranteeing a homogenous weld over the full width of the overlaps, usually set at 80 or 100 mm.

Conversely, the single-ply synthetic membrane (PVC-P, FPO/TPO or EPDM) prohibits any naked flame. Seaming is performed by hot-air thermal fusion using automatic welding machines for large standard runs, or manual tools equipped with a flat nozzle and a silicone pressure roller for details and upstands. The air-blowing temperature, adjusted between 400 and 550 °C depending on the material and external temperature, softens both faces without damaging them before mechanical pressing. For non-heat-weldable EPDM, seaming uses cross-linked adhesive tapes following application of a reactive primer.

On-site execution comparison: elastomeric bitumen versus synthetic membrane
Construction site criterionTwo-layer bituminous system (SBS)Single-ply synthetic membrane (FPO/PVC)
Primary energy and toolingPropane torch, gas cylinders, regulatorsElectric automatic welder, manual hot-air nozzle
Weather sensitivity during layingTolerates very low surface moisture under torch flameRequires a perfectly dry and clean seam zone
Immediate visual inspectionContinuous bead of melted bitumen visible at seamMechanical test using a blunt probe after cooling
Dead weight on structural frameHigh: approx. 8 to 10 kg/m² for both layersVery low: approx. 1.5 to 2.5 kg/m² depending on thickness
Thermal risk managementHot work permit often required, post-work fire watchMinimal fire risk, suitable for sensitive environments

Technical trade-off: structural constraints and substrate compatibility

The decision between bitumen and synthetic does not stem from workshop preference, but from strict alignment with roof use, thermal insulation type and mechanical loads according to standard SIA 271. A heavy inverted roof under gravel, a green roof or a trafficked terrace preferentially receives a two-layer bituminous system. Its structural redundancy provides an essential safety margin against puncture during subsequent site phases (earthworks, laying pavers on pedestals, planting). In the event of accidental damage to the top layer, the base sheet keeps the building watertight.

On industrial sheds with lightweight roofs (profiled steel decks, timber decks) where allowable live loads are reduced, the mechanically fastened single-ply synthetic membrane is almost systematically chosen. Its rapid installation over large spans offsets an increased vulnerability to punctures: on a single sheet of 1.5 to 2.0 mm, a single tear immediately breaches the entire waterproofing system.

Compatibility with the substrate also governs build-up composition. Plasticised PVC undergoes plasticiser migration when in direct contact with expanded polystyrene (EPS) or old bitumen layers: installing a polyester separation fleece (at least 300 g/m²) or glass mat is then essential. FPO membranes do not experience this incompatibility and are laid directly on rigid insulation. Finally, for green roofs, the choice of top layer must incorporate certified root-barrier treatment, whether an ester-salt-treated bituminous reinforcement or a synthetic resin inherently resistant to root penetration.

Damage management, non-conformities and emergency site decisions

On a flat roof construction site complying with standard SIA 271, noting an incompatibility or seam defect requires work to stop immediately to safeguard structural integrity. Premature damage often stems from direct contact between chemically incompatible materials, such as plasticiser migration from a single-ply synthetic PVC-P membrane installed without a separation layer over an old bituminous build-up or polystyrene insulation. Conversely, ill-considered torch use for a two-layer bituminous system on sensitive substrates or timber upstands exposes the structure to fire.

  1. Recording and traceability of defectsRecord defects: widespread blistering, absence of bitumen bead on seams, thermal delamination of a synthetic sheet, or overheating of combustible insulation under flame.
  2. Formal notice to site managementReport substrate non-conformities or execution risks in writing. According to art. 365 CO, the contractor notifies the client if the material supplied or the site compromises proper execution of the works.
  3. Precautionary securing measuresEnsure provisional watertight tie-ins at the end of the working day, ballast synthetic sheets exposed to wind, and protect bare insulation from precipitation.
  4. Remedial work according to codes of practiceReplace burnt or degraded areas. For synthetics, weld a patch using hot air after cleaning with suitable solvent; for bitumen, apply a fully torched reinforcing strip with compliant overlap.

The proofer's liability begins as soon as the substrate is taken over. If a material change proves essential — for example substituting a two-layer bituminous system for a single-ply synthetic membrane following dead-load or fire safety constraints —, written approval from site management and the waterproofing manufacturer remains mandatory prior to any final execution.

Frequently asked questions

Can a bituminous membrane be torched directly onto EPS or XPS insulation?

No. Direct flame contact instantly melts expanded or extruded polystyrene. According to standard SIA 271, substrate compatibility requires the prior installation of a self-adhesive or nailed base sheet, or using an insulation board factory-surfaced with a bituminous glass mat. The first layer protects the thermal insulation before torching the top layer of the two-layer bituminous system.

How is an accidental tear repaired on a TPO single-ply synthetic membrane?

The surface around the cut must be meticulously degreased with the manufacturer-specified cleaner to remove dirt and surface oxidation. A matching patch with rounded corners, extending at least 100 mm beyond the tear, is then welded with hot air using a hand-held hot-air tool and a silicone pressure roller.

When is a hot work permit mandatory for the proofer?

A hot work permit is required for all open-flame work near combustible materials: timber kerbs, sensitive insulation, penetrations, or refurbishments on old roofs with flammable residues. If safety coordination dictates excessive risk, the proofer replaces the torch with self-adhesive bituminous membranes or switches to a hot-air welded single-ply synthetic membrane.

What should be done if a concrete substrate has excessively high residual moisture?

Applying an impregnation primer and fully torching a two-layer bituminous system are prohibited on saturated concrete due to the risk of vapour blistering. The proofer issues a notice of non-conformity. Solutions consist of waiting for acceptable drying, using a specific vapour control layer for damp substrates fixed mechanically, or moving to a loose-laid, gravel-ballasted single-ply synthetic membrane.

Texts and standards cited

  • SIA 271Waterproofing of flat roofs and low-slope roofs
  • CO art. 365Material and site conditions: the contractor informs the client immediately if the material supplied by the client or the site conditions compromise execution of the work

In the same section