Skip to content
Website
🧱 CFC 226Drainage and hydraulic safetyChapter 5 of 10 in the section

Siphonic drainage: principle, value on large roofs and limits

This chapter sets out the execution rules for siphonic rainwater drainage on large flat roofs. You will learn to understand full-bore priming, to strictly comply with the hydraulic layout without altering the shop drawings, and to organise rigorous inspections of anti-vortex outlets to guarantee the safety of the structure.

Key takeaways

  • The system operates under full bore via negative pressure as soon as the calculated priming flow rate is reached.
  • The absence of gradient under the roof frees up usable volume and reduces underground collectors.
  • Any change of diameter or elbow on the construction site destroys the calculated hydraulic balance.
  • Regular cleaning of anti-vortex strainers is essential for proper priming during severe storms.

Understanding the negative pressure regime and its benefits on large flat roofs

Siphonic rainwater drainage
Rainwater drainage system operating at full bore without air inclusion. A special siphonic grille prevents air from entering the pipe. The vertical stack creates natural negative pressure through gravity, drawing water accumulated on the waterproofing membrane with very high flow rates and velocities.

Unlike a conventional gravity drainage system governed by standard SIA 271 where the pipe contains up to 70% air to ensure open-channel flow, the negative pressure system uses the entire cross-section of the pipe. The geometric height between the roof and the atmospheric discharge point defines the total driving head. This physical phenomenon allows significantly smaller nominal diameters to be used, often reduced by half compared with conventional rainwater stacks.

  1. Initial gravity flowUnder light rain, the water level on the membrane remains low. The outlet admits a mixture of air and water; the pipework operates under conventional gravity open-channel flow, without residual pressure.
  2. Sealing and primingThe downpour intensity increases and water reaches the deflector plate of the siphonic strainer. The geometry of the collar blocks air entrainment at the centre of the vortex. Residual air pockets are driven downstream by the flow velocity.
  3. Full negative pressure regimeThe pipe network fills completely with water. The vertical stack acts like a piston pulling on the suspended collector. Fluid velocity reaches 2 to 6 metres per second, generating effective self-cleansing of the pipes.
Technical comparison between gravity drainage and siphonic systems
Construction site parameterStandard gravity drainageSiphonic drainage under negative pressure
Pipe filling ratio30% to 70% (mandatory presence of air)100% at nominal load (full bore)
Gradient of horizontal collectors0.5% to 1.5% minimum towards the stack0.0% (pipes installed perfectly level)
Pipe diametersLarge diameters (e.g. DN 125 to DN 200)Small diameters (e.g. DN 50 to DN 100)
Trenches and pipework beneath foundation slabMultiple penetrations and buried inspection chambersA single connection at the foot of the façade
Clearance envelope beneath slabDisadvantageous gradient along roof soffitInstallation flush with beams and structure

Strict execution constraints, zero tolerance, and inspection imperatives

The siphonic rainwater network relies on a precise hydraulic balance calculated using dedicated software in accordance with standard SIA 271 and rainwater sizing guidelines. Each local head loss induced by an elbow, a reducer, or a branch directly contributes to balancing the pressures at each outlet. Consequently, construction site personnel must take no liberties regarding adaptation during assembly.

  • Strict prohibition on altering a pipe diameter or adding an elbow to bypass a service duct without a hydraulic recalculation validated by the technical design office.
  • Obligation to align high-density polyethylene pipes perfectly, using guide brackets and fixed points capable of taking up dynamic tensile forces.
  • Strict adherence to rainwater outlet levels: an outlet installed higher or lower than the shop drawing shifts its priming threshold.
  • Flawless watertight connection of the bituminous or synthetic sheet onto the metal or plastic outlet collar under a validated technical assessment.

Overflow management constitutes the second indispensable safety safeguard. On a large waterproofed roof, the siphonic system is calculated to discharge up to the reference design rainfall. Beyond that, a dedicated overflow network must take over. This emergency system may itself be siphonic or gravity-based using parapet weirs, but it must remain completely independent of the main drainage network and discharge its water onto visible external surfaces.

Finally, long-term performance requires a rigorous maintenance protocol. If an anti-vortex strainer becomes clogged with leaves, protective gravel, or moss, air enters the pipe or the flow rate becomes insufficient to achieve full-bore conditions. Maintenance contracts provide for at least two visits per year to remove the cover, clean the perforated basket, and verify the watertightness of the clamping flange.

Operating limits, priming thresholds, and overflow sizing

Rainwater drainage under negative pressure relies on full bore operation of the network: the absence of air in the pipe creates continuous suction that accelerates flow velocity. However, this dynamic involves a major physical constraint: the system only operates in siphonic mode from a critical rainfall intensity upwards, known as the priming threshold. During a moderate rain event, the installation behaves like a simple unventilated gravity drain with a restricted flow rate. The roof then experiences a temporary, perfectly normal water retention until the water depth reaches the siphonic grille and purges the air column.

Technical comparison: conventional gravity drainage versus siphonic drainage on flat roofs
Technical criteriaConventional gravity systemNegative-pressure siphonic system
Pipe filling ratio (h/d)0.5 to 0.7 (constant presence of air)1.0 (pipe completely submerged)
Gradient of horizontal collectorsContinuous gradient mandatory (0.5% to 1.5%)Zero gradient permitted (0%), strictly horizontal installation
Downpipe diametersLarge (prevents air locks)Very small (high suction velocity)
Sensitivity to level variationsTolerant of moderate deviationsZero tolerance, hydraulic calculations redone for each deviation
Management of extreme stormsFlow rate proportional to water depthFlow rate capped by cavitation, overflows mandatory

The cavitation phenomenon constitutes an impassable hydraulic boundary for siphonic networks. If subcooling or negative pressure drops below the vapour pressure of water, gas pockets form instantaneously in horizontal collectors, causing loss of prime, violent hydraulic shocks, and a sharp drop in discharge capacity. This is why a negative pressure drainage network can never be casually oversized to absorb millennial floods: an oversized diameter would prevent priming during regular storms, whereas undersizing would destroy suction through emulsion. Safety against extraordinary torrential rain therefore relies imperatively on a separate emergency overflow network.

Waterproofing interface, routing rigidity, and inspection protocol

On the construction site, the boundary between the waterproofing trade (CFC 226) and sanitary installations requires coordination down to the millimetre. The waterproofer connects bituminous or synthetic sheets directly onto the waterproofing flange integral to the outlet body. The level accuracy of this bowl dictates the mechanical survival of the whole assembly: an outlet positioned too high relative to the intended water plane prevents hydraulic priming, leaving tonnes of water ponding on the load-bearing structure. Conversely, an outlet clamped too low creates a point of tensile stress on the membrane during thermal movements of the substrate.

  1. Setting out and levelling the bowlMechanically fix the outlet body to the concrete structure or steel profile according to the exact level coordinates provided by the plumbing engineer. No level adjustment is permitted on the construction site without a complete recalculation of the hydraulic study.
  2. Connecting the waterproofing membraneConnect the factory-supplied waterproofing flange by homogeneous welding or stainless steel clamping flange. The waterproofing must be free of any folds or parasitic extra thickness at the inlet to the outlet's baffle chamber.
  3. Fitting the anti-vortex grilleInsert the turbulence baffle fitted with its air deflector. This profiled component blocks surface vortices that would introduce air into the pipe, thereby ensuring continuous suction at full bore.
  4. Clamping the PE-HD pipeworkCheck the rigid fixing under the roof on electro-galvanised rails using fixed and sliding brackets. Thermal expansion and internal negative pressure require a mechanical strength capable of absorbing considerable axial tensile forces.

If the internal route of the PE-HD collector encounters an unforeseen service duct, cable tray, or ventilation shaft, the installer cannot reroute the pipe using convenient elbows. Any change in length or change of direction at a single fitting alters the linear head loss and disrupts the priming of all other outlets connected to the same stack. In the event of an unforeseen obstacle on the construction site, the contractor refers to the reporting obligations set out in art. 365 al. 3 CO to alert site management and the specialist engineering office before any modification to the approved routing.

Managing execution deviations and resolving hydraulic malfunctions

On a long-span industrial or commercial flat roof, the failure of a siphonic rainwater drainage system is unforgiving. As soon as a geometric discrepancy arises between the thermodynamic engineer's calculation report and the actual installation of the pipes along the roof soffit, the system loses its hydraulic balance. If a suspension point has been shifted to avoid a cable tray, or if the gradient has been altered without recalculation, full-bore filling no longer occurs at the design nominal flow rate. Water accumulates on the waterproofing assembly, threatening the stability of the steel framework or metal decking.

As soon as a non-conformity is observed on the suspended drainage network or on the siphonic outlets, the waterproofer immediately enters reservations in the site logbook. art. 365 CO requires the contractor to inform the client if any circumstance jeopardises the proper or punctual execution of the work. Connecting emergency safety overflows to negative pressure collectors is strictly prohibited. If a blockage is identified during hydraulic testing, aggressive mechanical drain snakes must not be used without supervision, to avoid puncturing mirror-welded high-density polyethylene.

  • Rigorous dimensional check of bowl positions relative to the low points of the fall.
  • Verification of the tightening torque on electrofusion couplers and locking of anti-vibration rails beneath the slab.
  • Complete cleaning of gravel-guard baskets and overflow crowns prior to any provisional acceptance of the waterproofing.
  • Immediate reporting to site management of any clash with HVAC and electrical installations.

When the installation becomes clogged due to lack of maintenance, anti-vortex grilles are cleared manually, without removing the calibrated air-throttling components. If a technical dispute arises regarding discharge capacity, a compartmentalised flooding test using a calibrated flowmeter allows responsibility to be established between the waterproofer and the plumbing design office.

Frequently asked questions

Why is it strictly prohibited to alter the location of a siphonic bowl on the construction site?

Each siphonic outlet is sized according to a specific catchment area and a hydraulic head loss calculated to the millimetre by software. Moving a bowl alters the driving drop height and the length of the horizontal PE-HD pipes. This alteration prevents synchronised priming of negative pressure at full bore during heavy rainfall, causing abnormal water accumulation on the waterproofing.

How should one respond if the anti-vortex basket of a siphonic outlet is damaged or missing?

The component must imperatively be replaced with the original model certified by the system manufacturer. Without its precise aerodynamic profile, air rushes into the stack, creating standard swirling gravity flow. Discharge capacity is then reduced by a factor of three or four. The flat roof loses its safety drainage capacity, increasing the risk of structural overload on the structural work.

What is the gradient tolerance on horizontal collectors suspended beneath the roof?

Collectors along the soffit are generally installed with zero gradient, meaning strictly horizontal, in accordance with the system's technical specifications. The alignment tolerance does not exceed a few millimetres. A local backfall creates a permanent air pocket that blocks the hydraulic draw effect, whereas an excessive gradient accelerates flow asymmetrically and disrupts the negative pressure priming of other connected outlets.

How often and according to what protocol must siphonic drainage systems be maintained?

Inspection is carried out at least twice a year, in spring and late autumn, in accordance with roof maintenance contracts. The operation includes manual removal of moss, leaves, and organic debris around the outlets, thorough cleaning of the siphonic plate vanes, and a visual check of the waterproofing membrane clamped into the mechanical clamping flange of the unit.

Texts and standards cited

  • CO art. 365materials and site conditions: the contractor immediately informs the client if any circumstance jeopardises the proper or punctual execution of the work

In the same section