Skip to content
Website
🧱 CFC 226Upstands and special detailingChapter 6 of 10 in the section

Internal and external corners: prefabricated angle pieces and corner reinforcements

After reading this chapter, you will be able to identify the three-dimensional mechanical stresses experienced by waterproofing upstands in corners. You will master the selection of prefabricated reinforcement pieces according to standard SIA 271, the precise welding sequence of the layers, and the techniques to permanently eliminate manual folding, which is the root cause of water infiltration.

Key takeaways

  • Forced folding in the workshop or on the roof stretches the reinforcement and causes rapid tearing.
  • Standard SIA 271 prescribes specific reinforcement pieces to neutralise corner stresses.
  • The prefabricated corner piece is always installed before the main upstand run on the base layer.
  • Visual inspection of the bitumen bead or synthetic weld validates the three-dimensional watertightness.

Why forced folding of the membrane creates a predictable failure point

On a flat roof, the junction between the horizontal plane and two perpendicular vertical planes constitutes a critical singular point. In an internal or external corner, the waterproofing membrane experiences a three-dimensional stress state: thermal shrinkage, differential masonry movements, and wind uplift concentrate there. When an installer attempts to dress down a bituminous or synthetic sheet by folding the material 'envelope-style' or by forcing the heel when heated, they excessively stretch the polyester or glass fleece reinforcement. This local deformation thins the binder, weakens the elastomeric or plastomeric compound, and generates microcracks invisible to the naked eye during installation.

Standard SIA 271 requires flawless continuity of waterproofing performance and damage-free absorption of predictable building movements. Manual folding invariably creates an underlying thermal bridge with an air pocket at the bottom of the fillet, or conversely, a rigid build-up of three to four superimposed layers on the external edge. This excess thickness prevents proper roller pressure, creates capillary channels along the selvedges, and prevents the top metal capping profile from sitting flush.

Corner gusset or patch
A geometric piece cut or thermoformed in the factory, inserted at the three-dimensional convergence point to guarantee the nominal waterproofing thickness without mechanical over-tensioning of the material.
Mechanical behaviour of corners according to execution method
MethodResistance to thermal movementPuncture riskStandard SIA 271 compliance
Manual envelope foldingZero (reinforcement under permanent tension)High (air pocket under the heel)Non-compliant
On-site cutting and flat patchLow (loss of continuity at the apex)Medium (rupture of the binder film)Non-compliant
Factory prefabricated angle piece or componentOptimum (homogeneous and stress-free material)Zero (perfect adaptation to the substrate)Compliant

Installation of prefabricated angle pieces and welding sequence

The use of factory-preformed components – whether internal or external corners made of polymer bitumen or synthetic material (FPO, PVC) – eliminates all stretching work on the construction site. Installation requires strict adherence to substrate preparation: the vertical masonry edge must have a uniform chamfer or be arrised, and the horizontal junction must include a rigid triangular fillet strip or a rounded fillet complying with the requirements of standard SIA 271 to avoid a sharp ninety-degree angle.

  1. Preparation and priming of the substrateDe-dust the concrete, grind down protruding edges, and apply a bituminous primer to the parapet wall and slab, allowing it to dry completely before applying any heat.
  2. Installation of the prefabricated corner reinforcementWeld the preformed piece (gusset or corner angle piece) first. The horizontal heel must extend at least 100 mm onto the roof surface and extend at least 100 mm up each vertical face.
  3. Installation of the upstand angle reinforcement stripApply the angle reinforcement strip with a minimum lap of 80 mm over the prefabricated piece, smoothing down firmly from the centre to the edges using a silicone roller.
  4. Connection of the main waterproofing layerOverlap the upstand strip with the main roof sheet, ensuring staggered joints so that a field sheet weld is never superimposed onto the apex of the corner.

On hot-air welded synthetic systems, the site foreman ensures the temperature setting of the hand tool according to ambient temperature and membrane type. Rounding each cut membrane corner in advance prevents tear initiation. Final inspection is carried out without exception using a dry blunt probe along the entire perimeter of the corner piece once the weld seams have cooled down completely.

Geometry of corner pieces and execution of laps

Three-dimensional corner reinforcement
Factory-preformed element or component cut from an unreinforced flexible membrane, designed to ensure watertightness at the convergence of three orthogonal planes without placing its reinforcement under tension.

Standard SIA 271 defines stringent requirements for detailing connections and waterproofing upstands. In corners, the membrane experiences a triaxial stress state caused by thermal shrinkage of the sheets, differential movements between the slab and parapet walls, and residual settlement of the thermal insulation. Incorporating a prefabricated angle piece is the only solution that guarantees a uniform binder thickness within the dihedral. Unlike a standard sheet forced into place manually, the moulded or preformed piece conforms to reliefs without stretching its reinforcement, eliminating any risk of necking or thinning of the protective compound at the point of convergence.

Installation specifications for internal and external corners
Execution criterionInternal corner (fillet base)External corner (parapet projection)
Dominant stressMultidirectional tension and thermal compressionMechanical edge shearing and fibre stretching
Corner substrate shape45° triangular fillet or angle fillet over full heightSharp edge chamfered or rounded to a 10 mm radius
Component installation sequence1. Fillet, 2. Base reinforcement piece, 3. Vertical upstands1. External corner reinforcement, 2. Upstand angle piece, 3. Flashing strip
Typical waterproofing defectBridging (tenting), tearing beneath heavy ballastAxial cracking on the corner due to shrinkage

The installation sequence of components determines the hydraulic effectiveness of the construction detail. The recurring error consists in fitting the vertical upstands before applying the corner piece: this inverted assembly promotes capillary infiltration and generates a poorly welded build-up at the junction of the horizontal heel. The corner reinforcement must imperatively be welded and checked around its entire perimeter prior to installing the upstand sheets. These then overlap the piece by at least 100 mm. Complete fusion is required to prevent air pockets along the toe fillet.

Inspection of corner welds and failures from manual fabrication

Forced on-site folding of a bituminous membrane reinforced with glass fleece or polyester causes immediate structural degradation. Under the combined action of flame and manual pressure, the elastomeric bitumen flows while the reinforcement is sheared by the fold, creating a crack initiation point undetectable to the naked eye. As soon as the first winter temperature drops occur, thermal contraction of the roof stresses this weak point. The membrane then ruptures precisely on the folded edge. Prefabricated angle pieces eliminate this defect by providing a three-dimensional profile free of residual stress, perfectly stable under dimensional variations of the building.

  1. Preliminary cleaning of welding zonesCarefully brush the selvedges of the prefabricated piece to remove talc, fine sand, or oxidation residues that reduce adhesion quality.
  2. Visual inspection of the bitumen bleed-outCheck for the presence of a continuous 5 to 10 mm bitumen bead expelled along each overlap, confirming uniform fusion of the material without overheating.
  3. Systematic mechanical probing using a blunt probeRun a blunt rounded probe along the entire perimeter of the corner piece, applying slight upward pressure to detect unbonded seams.
  4. Adhesion check at the bottom of the filletEnsure by firm thumb pressure that the reinforcement fits snugly into the angle without forming a hollow bridge above the upstand toe fillet.

The meticulous execution of singular points is part of the waterproofing contractor's professional obligations. Under art. 364 CO, the contractor's liability is subject to the same rules as those governing an employee for the execution of the work. On a flat roof, failures predominantly stem from poorly detailed corners. The systematic use of certified prefabricated angle pieces combined with strict compliance with the component installation sequence permanently eliminates the risk of tearing and guarantees compliance of the work with standard SIA 271.

Remedial procedure for non-compliant or leaking corners

Identifying a forced fold, bridging without adhesion at the bottom of the fillet, or tear initiation on an internal or external corner requires total refurbishment of the singular point. According to standard SIA 271, waterproofing continuity and the transfer of triaxial stresses require full adhesion and a geometry free of residual stress. A simple superficial patch or surface heating with a torch never resolves the underlying void. Water infiltrates by capillarity behind the assembly as soon as the first seasonal temperature swings occur.

  1. Stripping and cleaning the substrateRemove unbonded or wrinkled membrane using a hot knife or grinder. Cut back the area by at least 150 mm on either side of the edge to expose a sound, dry, and rigid substrate.
  2. Installation of the base corner reinforcementApply a primer if necessary and fully bond a base gusset. In an internal corner, roll out the fillet thoroughly with a pressure roller to eliminate any bridging.
  3. Integration of the prefabricated angle piecePosition the factory-moulded prefabricated angle piece. Weld using a torch or hot air, always working outwards from the zero point to expel air and obtain a continuous 5 mm bleed-out bead.
  4. Connection and bridging of main sheetsApply the upstand flashings and surface strips. Maintain a minimum overlap of 100 mm over the flanges of the corner piece, bevelling the selvedges to neutralise lateral water ingress.

The component installation sequence allows no improvisation during remedial work. If defective execution is identified during works inspections, the provisions of art. 368 CO apply to demand rectification of the non-compliant part. Methodical cutting away of the failed assembly followed by the successive integration of a corner reinforcement and then an industrial component are the only way to guarantee a durable connection on the building.

Frequently asked questions

Why is forming a corner directly with the main upstand sheet prohibited?

Forced manual folding of a bituminous or synthetic membrane subjects the material to excessive three-dimensional stretching along the edge. This deformation stretches the non-woven reinforcement beyond its elastic limit, thins the effective waterproofing thickness, and creates microcracks invisible to the naked eye. Using a prefabricated angle piece eliminates these mechanical stresses by providing a geometry moulded to exact dimensions, thereby guaranteeing a uniform material thickness and continuous welding to the substrate.

In what exact sequence should the components of an internal corner on a parapet upstand be installed?

The component installation sequence begins with the application of priming lacquer and the installation of a corner reinforcement gusset at the bottom of the fillet. Next comes the internal corner prefabricated angle piece, fully bonded. The parapet upstand sheets then overlap the vertical flanges of the piece with a lap of at least 100 mm. Finally, the main roof membrane is welded horizontally, ensuring gravity drainage towards the outlets without backfalls.

How do you inspect the watertightness of an external corner before installing insulation or protective layers?

The inspection is performed once the welds have cooled completely. The foreman uses a dry blunt probe or a roofer's spatula with rounded edges to test the entire perimeter of the prefabricated corner piece. No disbonding or lack of bitumen bleed-out must be found. On synthetic membranes, a vacuum bell test or high-voltage spark tester confirms the absence of microscopic pinholes, in accordance with the acceptance rules of standard SIA 271.

Can a prefabricated angle piece be installed without chamfering the edge laps?

No, chamfering laps at 45 degrees along the edges is mandatory to prevent material build-up known as lap intersections (T-joints). Without this chamfered cut, the fourfold layer of membrane creates a capillary channel that the pressure roller cannot properly flatten. Hot air or flame cannot hermetically seal this bridge, creating an immediate risk of water infiltration beneath the waterproofing upstand.

Texts and standards cited

  • SIA 271Building waterproofing
  • CO art. 368employer's rights in case of defects in the work: rejection, price reduction, rectification, damages

In the same section