Skip to content
Website
🧱 CFC 226Substrate, slope, vapour barrier and thermal insulationChapter 9 of 10 in the section

Separation layers: chemical incompatibilities between membrane and substrate

This chapter details the chemical degradation mechanisms between synthetic membranes, bitumens and thermal insulations on flat roofs according to standard SIA 271. You will learn how to identify precisely incompatible material pairs on the construction site, specify the correct separation fleece and systematically check tolerances with the manufacturer to ensure the durability of the structure.

Key takeaways

  • Direct contact between plasticised PVC and bitumen or polystyrene causes the destruction of the waterproofing.
  • Standard SIA 271 requires an effective separation layer between chemically incompatible components.
  • Synthetic geotextiles or glass fleeces neutralise the migration of volatile plasticisers.
  • Written approval from the membrane manufacturer remains essential before any complex installation.

Identify incompatible pairs and the plasticiser migration mechanism

On a flat roof, the direct juxtaposition of certain waterproofing and insulation materials causes destructive physico-chemical reactions. The most critical case concerns synthetic membranes made of plasticised polyvinyl chloride (PVC-P). These sheets contain volatile plasticisers intended to give them flexibility. When a PVC-P membrane comes into direct contact with bitumen, solvents or expanded (EPS) or extruded (XPS) polystyrene insulation, these plasticisers migrate out of the polymer sheet towards the receiving substrate.

This migration phenomenon leads to irreversible double degradation. On the one hand, the PVC-P membrane loses its flexible constituents: it hardens, undergoes significant dimensional shrinkage, cracks under thermal stresses and eventually fails at fixings or welds. On the other hand, mineral oil residues and hydrocarbon compounds from bitumen or styrene attack the polymer surface through partial dissolution. High temperatures reached on the roof during summer considerably accelerate these chemical kinetics.

Direct compatibility matrix between waterproofing membranes and common substrates
Synthetic membraneBituminous substrate (new or old)Polystyrene (EPS / XPS)Fleece-faced polyurethane (PIR)Mineral wool
PVC-P (plasticised)Incompatible (separation mandatory)Incompatible (separation mandatory)Compatible depending on manufacturer sheetCompatible
FPO / TPO (polyolefins)Generally compatibleCompatibleCompatibleCompatible
EPDM (elastomer)Compatible without active solventCompatibleCompatibleCompatible

Install separation fleeces and validate assembly compatibility

To prevent any degradation of the structure, standard SIA 271 prescribes the systematic interposition of a separation or protection layer between chemically incompatible layers. This physical barrier prevents direct contact and blocks molecular transfer. The choice of interlayer material depends on the nature of the products present, the membrane fixing method (ballasted, bonded or mechanically fastened) and the mechanical resistance requirements associated with the substrate.

  • Glass fleece: rot-proof and non-combustible, generally used with a minimum grammage of 120 g/m² as an anti-migration barrier beneath synthetic membranes laid over polystyrene panels.
  • Non-woven polypropylene or polyester geotextile: commonly used between 150 g/m² and 300 g/m² to act as a barrier over bituminous substrates while providing puncture protection.
  • Fleece-backed composite membranes: synthetic membranes factory-laminated with a polyester fleece on the underside, allowing direct laying on insulation or suitable adhesive.
  1. Substrate inspectionCheck the exact nature of the insulation or old waterproofing build-up. Identify the presence of residual bitumen, traces of hydrocarbons or solvent-based adhesives.
  2. Verification with the manufacturerConsult the technical data sheets for the selected waterproofing system. Obtain written confirmation from the manufacturer regarding the compatibility of the planned pair and the exact type of barrier required.
  3. Laying the separation layerUnroll the fleece or geotextile dry, directly onto the insulation or bitumen. Maintain a minimum overlap of 100 mm between sheets to ensure complete continuity without gaps.
  4. Detailing joints and upstandsRun the separation fleece up to the top of the upstand against any adjacent bituminous element or insulation before applying bridging or fastening strips.

Matrix of chemical incompatibilities on flat roofs

The design and installation of single-ply synthetic waterproofing systems require a systematic analysis of the underlying layers. According to standard SIA 271, direct contact between chemically incompatible materials leads to premature degradation of the waterproofing build-up. Plasticised polyvinyl chloride (PVC-P) membranes prove the most vulnerable due to the extraction of their liquid plasticisers upon contact with solvents, oils or hydrocarbons present in bituminous substrates and certain insulation boards.

Direct compatibility and separation requirements between synthetic membranes and substrates
Membrane typeUnderlying substrate or insulationObserved chemical riskRequired constructive measure
Standard PVC-PBitumen (new or old)Reciprocal migration: plasticisers absorbed, bitumen dissolved, embrittlementSynthetic separation fleece or specific bitumen-resistant membrane
Standard PVC-PExpanded polystyrene (EPS) or extruded polystyrene (XPS)Attack on polystyrene, hardening and cracking under mechanical stressSynthetic-fibre or glass separation fleece
FPO / TPO (flexible polyolefins)Bitumen / Polystyrene (EPS, XPS)No liquid plasticiser: no chemical extractionDirect installation permitted according to technical system approval
EPDM (synthetic elastomer)Fresh bitumen or formwork release oilsLocalised swelling of the elastomer sheet due to absorption of distillatesSeparation layer or vulcanisation over cleaned and remediated substrate
All single-ply membranesRough concrete or dusty laitanceDynamic puncturing and abrasive expansion stressesProtection layer or rot-proof surfacing felt

Superficial liquefaction of bitumen upon contact with PVC-P leads to contamination of the sheet's underside, preventing any subsequent heat welding during a joint or repair. Molecular transfer makes the waterproofing brittle under winter thermal shocks, with risks of seam opening due to dimensional shrinkage.

Construction site protocols and manufacturer verification

Membrane and insulation incompatibility does not end with the initial laying phase in the main area. Specific details such as skylight upstands, parapet upstands and ventilation penetrations require identical vigilance. The waterproofer must ensure that bevelled EPS thermal insulation fillets do not come into direct contact with the unlined upturned sheet.

  • Insulation inspection: identify CE marking or Swiss approval indicating compatible factory facing (mineralised glass fleece on polyurethane or polystyrene).
  • Installation of a separation fleece: unroll a glass felt of at least 120 g/m² or a polyester non-woven of 200 to 300 g/m² with a dry overlap of 100 mm at the seams.
  • Handling mechanical fasteners: verify that metal distribution plates or polyamide sleeves do not crush the separation fleece so much that they create contact bridges between the PVC-P and underlying insulation.
  • Perimeter detailing: insert a non-woven interposition strip behind PVC-clad metal sheets installed over a substrate coated with bitumen emulsion residues.

In accordance with the Code of Obligations (CO), the contractor is liable for the satisfactory quality of the material supplied. Art. 365 CO specifies that if the material supplied by the client or the site designated by them is found to be defective, or if any other circumstance jeopardises the regular or punctual execution of the work, the contractor must inform the client immediately, on pain of bearing the consequences. This formal notification is mandatory as soon as bare insulation boards are found to be incompatible with the membrane specified in the tender bill.

Verification with the manufacturer remains the decisive step before installing any non-standardised material pair. Technical notices provide approval tables for contact adhesives, bonding primers and geotextiles validated in test laboratories. Written certification from the waterproofing manufacturer releases the site foreman from technical liability regarding risks of delamination or chemical attack under climatic loads.

Management of incompatibility claims and remediation according to standard SIA 271

Late discovery of chemical incompatibility on a flat roof manifests as localised softening of a synthetic sheet, parasitic adhesion of a PVC-P membrane strip onto an expanded polystyrene (EPS) panel, or oozing of plasticiser oils over old bituminous waterproofing. In these situations, the build-up loses its watertightness as well as its mechanical expansion properties. According to standard SIA 271, directly superimposing incompatible materials without interposing a suitable screen constitutes an execution defect that compromises the durability of the structure.

  1. Section shutdown and joint technical assessmentHalt laying in the affected zone. Record in writing the nature of the layers in contact, exact references of sheets and insulations, then carry out targeted destructive exploratory cuts to determine the extent of material degradation.
  2. Technical consultation with the system manufacturerSubmit the file to the membrane manufacturer's technical department for a written assessment. Verification with the manufacturer determines whether the material has lost its elongation properties and whether partial remediation remains admissible.
  3. Cutting out contaminated areas and stripping degraded substratesCut out and dispose of the hardened synthetic waterproofing. If the EPS or polyurethane insulation exhibits melting craters or paste-like residues, plane down or completely replace damaged panels to restore a flat substrate.
  4. Interposition of a separation fleece and patchingLay a synthetic non-woven geotextile of at least 300 g/m² or a suitable glass fleece with a generous overlap of at least 100 mm, then hot-air weld a new patch of compatible membrane.

A contractor who observes an anomaly in the prescribed materials or substrate during work applies the principles of the Code of Obligations (CO) by notifying site management without delay. For pricing a complete remedial build-up or localised replacement of a deteriorated insulation build-up, amounts range roughly from 45 to 95 CHF per square metre excluding taxes depending on roof accessibility and existing ballast, to be confirmed under /tenders/.

Frequently asked questions

Can an FPO membrane be laid directly over old bituminous waterproofing without a barrier?

Most flexible polyolefin (FPO/TPO) synthetic membranes exhibit excellent resistance to hydrocarbons and tolerate direct contact with oxidised or polymer bitumen. However, according to standard SIA 271, verification with the membrane manufacturer remains mandatory prior to execution. If coal tar pitch residues, active solvents or aggressive substrate roughness are present, laying a non-woven separation fleece remains mandatory to preserve watertightness.

What separation fleece grammage should be specified between EPS insulation and a PVC-P sheet?

Between expanded (EPS) or extruded (XPS) polystyrene boards and a plasticised PVC-P waterproofing membrane, interposing a screen is required to prevent plasticiser migration. A non-woven polypropylene or polyester felt of at least 300 g/m² is installed, or a specific glass fleece certified by the system manufacturer. The separation fleece sheets must overlap dry by at least 100 mm.

How should water penetration be treated if a PVC membrane has melted locally on bitumen?

It is impossible to repair a weakened PVC-P membrane by direct welding. The protocol requires cutting out the rigidified membrane area broadly until flexible, sound material is reached. The exposed bituminous substrate must be isolated by applying a rot-proof synthetic fleece overlapping by 150 mm. A new PVC-P patch is then positioned and hot-air welded around the perimeter, checking the seam with a dry seam probe.

Why are bituminous sealants and self-adhesive tapes prohibited beneath flexible synthetic sheets?

Adhesives, waterproofing sealants or joint tapes containing active solvents or non-deactivated bituminous components immediately diffuse volatile compounds into thin PVC sheets. This chemical incompatibility causes breakdown of the reinforcing scrim and total loss of mechanical tightness. Only polyurethane sealants, hybrid polymers or sealing tapes approved by the synthetic system supplier in accordance with standard SIA 271 recommendations must be used.

Texts and standards cited

  • norme SIA 271Flat roofs: construction details, material compatibility, separation layers and waterproofing

In the same section