Key takeaways
- Bituminous or synthetic waterproofing upstands require continuous mechanical anchoring at the parapet head.
- Bonding or welding alone never compensates for slippage caused by repeated thermal variations.
- The metal clamping strip ensures continuous pressure beneath the upper termination seal.
- The coping protects the head against weathering with a vertical overlap and a drip edge.
Mechanical top fixing and installation of the clamping strip
On a flat roof, thermal and mechanical stresses exerted on the waterproofing membrane are highest at upstands. Simple bonding, whether carried out with hot bitumen or contact adhesive on a synthetic sheet, undergoes creep over time under the combined effect of gravity and summer heating. According to the rules of standard SIA 271, the upper edge of each upstand must receive continuous, non-deformable mechanical top fixing, anchored directly into the rigid substrate of the parapet.
- Clamping strip
- A rigid metal profile made of extruded aluminium or stainless steel, pre-drilled, designed to uniformly distribute continuous linear mechanical pressure across the top of the waterproofing upstand.
The clamping strip is the central component for top retention. This rigid profile prevents the membrane from gaping between two anchoring points. The waterproofer must avoid isolated screws penetrating the membrane without a load-spreading profile, as wind or thermal shrinkage tears the reinforcement at each fastener shank. Clamping must firmly compress the membrane against the concrete or timber board without shearing the material.
- Preparation and cutting of the upstand sheetAdjust the height of the bituminous or synthetic membrane so that it rises up to the prescribed termination level, with a minimum overlap of 20 mm above the intended anchoring line.
- Positioning the clamping stripPress the pre-drilled metal profile flat against the crown or inner face of the parapet. Align the bars strictly, leaving an expansion gap of 2 to 3 mm between each profile length.
- Drilling and pluggingDrill into the reinforced concrete substrate through the slotted holes of the profile, vacuum the drilling dust, then insert corrosion-resistant mechanical fixings suited to the solid or hollow substrate.
- Tightening and sealingTighten the mechanical fixings to the prescribed torque to achieve uniform pressure along the strip, then apply a bead of compatible elastomeric sealant into the upper groove of the profile.
| Type of parapet substrate | Type of mechanical fixing | Maximum fixing centres | Minimum embedment depth |
|---|---|---|---|
| Solid reinforced concrete | Hammer-set anchor or stainless steel concrete screw | 250 mm | 35 mm |
| Clay or sand-lime brick | Nylon expansion plug with stainless steel screw | 200 mm | 50 mm |
| Timber frame or plywood board | Large flat head stainless steel wood screw | 200 mm | 40 mm |
Protection by coping and geometric overlap
Once the top of the upstand is mechanically fixed, the system must be protected against direct rain penetration, ultraviolet rays, and accumulated snow. Installing a metal coping capping the entire parapet provides this durable protection. In the common configuration of a clad parapet, the waterproofing upstand runs up the full vertical height of the inner upstand, passes over the horizontal or inclined crown, and is capped by this rigid cover.
Upstand waterproofing must be protected against mechanical damage and water ingress at the top. The parapet crown must feature a fall towards the roof and ensure effective water shedding clear of the facade.
norme SIA 271
The geometric dimensioning of the coping overlap meets precise requirements. The downstand of the folded sheet must overlap the clamping strip or membrane by at least 50 mm for a standard building height, and reach 100 mm on buildings particularly exposed to wind in mountain areas. The parapet crown must have a minimum fall directed towards the interior of the roof to prevent dirty run-off on exterior facades.
- Fall on the crown directed towards the interior of the roof surface, ideally equal to or greater than 2%.
- Continuous external drip edge maintaining a gap of at least 20 mm from the face of the facade.
- Cleats or continuous brackets avoiding through-perforations in the coping exposed to rain.
- Splice plates or sliding joints allowing free thermal expansion of the metal without stressing the upstand.
During operations on flat roof perimeters lacking high parapets, fall protection must be ensured in accordance with the provisions of OTConst art. 23, which requires the installation of perimeter edge protection whenever the fall height exceeds 2 metres. The organisation of the construction site for installing clamping strips and copings involves either set-back bracket scaffolding or collective perimeter protection ensuring work along the edge without obstructing the fixing of the upstand top.
Corner detailing, butt joints and management of thermal expansion
The mechanical fixing at the top of the upstand allows no discontinuity at changes of plane. While the main run on the parapet wall receives rigid profiles of a standard length of two to three metres, detailing internal and external corners requires rigorous prior fabrication. The bituminous or synthetic sheet rises to the crown level specified by standard SIA 271; it must be held tight against the concrete substrate without forming air pockets or creases in the corner. A common mistake on construction sites consists in bending a one-piece rigid clamping strip across the corner: the mechanical stress exerted by the folding machine deforms the profile, pulls the mastic seal away from the concrete, and creates an immediate water path beneath the drip.
In each corner, two separate profile elements must be fitted with a neat mitre cut. Each section is anchored less than fifty millimetres from the corner with a hammer-set anchor or a direct-thread concrete screw. This arrangement counteracts pull-out forces generated by air turbulence along roof perimeters. Between two consecutive lengths of clamping strip on straight runs, an expansion gap of three to five millimetres must strictly be provided to absorb thermal elongation of the aluminium or stainless steel. Continuity of the waterproofing function is ensured by filling this gap with polyurethane or MS polymer mastic suited for exterior use.
| Parapet assembly component | Standard material | Required expansion provision | Key inspection point during installation |
|---|---|---|---|
| Clamping strip at sheet head | Extruded aluminium or stainless steel (1.5 to 2 mm) | 3 to 5 mm gap between consecutive profiles | Placement of an anchor at each profile end |
| Upper sealant bead | Polyurethane or MS polymer elastomeric mastic | Intrinsic elasticity of calibrated bead | Prior cleaning and degreasing of receiving chamfer |
| Capping coping | Folded aluminium, zinc-titanium or copper | Sliding joints or splice plates with 5 mm clearance | Indirect fixing on cleats to allow the metal sheet to slide |
| Coping fixing brackets | Galvanised steel or reinforced aluminium | Maximum centres of 600 mm | Transverse fall of at least 2% inwards |
Above the clamping strip, the coping provides umbrella protection for the parapet top and the upper waterproofing junction. The coping overlap must be mechanically decoupled from the sheet clamping: securing the metal apron of the coping and the clamping strip together with the same fixing creates a thermal bridge and locks the freedom of movement required for metal expansion. Copings are clipped or screwed onto brackets fixed independently to the parapet crown. Junctions between coping elements receive underlying splice plates or waterproof sliding joint covers, ensuring rainwater run-off without stressing the sealing mastics.
Wind requirements, water clearance and installation inspection according to standard SIA 271
Climatic stresses on parapet tops combine the effects of driving rain with wind pressure and suction. According to standard SIA 271, the geometry of the crown must prevent any water bypassing behind the waterproofing upstand. The external drip edge of the coping must extend downwards vertically to overlap the upper edge of the clamping strip or sheet by at least fifty millimetres. A minimum clearance of twenty millimetres between the drip fold and the vertical wall face prevents capillary rise and sheds water clear of the junction zone.
On new or refurbishment construction sites, the condition of the parapet substrate determines anchor holding capacity. If the concrete crown or masonry exhibits spalled, porous or friable areas, anchors lose pull-out resistance under roof perimeter wind uplift. In accordance with art. 365 CO, the waterproofer reports defects noted in the rough structure that jeopardise the durable fixing of the system. Plug holes must be cleared of dust before expansion, and screws installed using a torque limiter to avoid crushing the ribs of the extruded aluminium strip.
Internal acceptance of the upstand includes checking profile alignment, verifying continuous compression of the elastomeric seal at the top, and measuring the projection of the coping drip edge. The transverse fall of the crown must systematically shed water towards the roof surface, at a minimum of 2%, to prevent standing pools beneath the metal sheet. This check prevents water ingress from ice back-up in winter and extends the service life of the waterproofing system in accordance with recognised trade requirements.
Diagnosis of top-of-upstand non-conformities and corrective measures
On a flat roof, slippage of a bituminous or synthetic sheet along the upstand almost always indicates missing mechanical top fixing or excessive anchor spacing. Simple bonding with hot bitumen or contact adhesive cannot withstand thermal cycles and creep under the self-weight of the membrane. When waterproofing detaches or wrinkles beneath the capping, the foreman must take action before rainwater penetrates behind the insulation build-up.
In accordance with standard SIA 271, the top edge of the waterproofing must be continuously retained and protected against direct run-off. If the concrete substrate has spalls or if the upstand timber is rotted, the anchor loses all holding power. Art. 365 CO requires the contractor to notify the client if the ground, materials, or any circumstance jeopardises the proper or timely execution of the work.
- Removal and probingDismantle the metal coping and check the condition of the waterproofing upstand. Check the strength of the masonry or concrete substrate after pull-out of failed fixings.
- Mechanical remediation of the topPress the sheet flat again, remove degraded sections, then insert a rigid aluminium profile. Secure using suitable screws with centres reduced to 200 mm maximum.
- Connection and sealingTorch a bridging strip or apply flashing with a reglet flange filled with weather-resistant mastic to block any incoming water path from above.
- Reinstallation of copingReinstall brackets ensuring a vertical overlap of at least 50 mm over the head of the waterproofed upstand, with a fall directed towards the roof.
When the parapet lacks a sound concrete head, installing a use class 3 treated timber upstand kerb is required in agreement with site management. All corrective work is documented in minutes supported by photographs prior to final closure of the sheet metal work.
Frequently asked questions
Does a metal coping dispense with installing a clamping strip at the upstand top?
No. The coping protects the wall head against driving rain and impact, but it does not provide mechanical anti-slip retention for the membrane. Without a rigid rail and continuous plugging beneath the coping, bituminous or synthetic waterproofing undergoes vertical creep, debonds under thermal stress, and ultimately allows moisture behind the insulation.
What maximum centres must be maintained when plugging the clamping strip on concrete parapets?
On masonry or concrete, the perforated metal profile must be anchored with maximum spacing of 200 to 250 mm between screws or hammer-set anchors. Wider spacing causes the profile to gape between anchor points under expansion effects, destroying the top seal and allowing warm air and water to penetrate.
What fall must be provided on the parapet head beneath the coping according to standard SIA 271?
The parapet crown must strictly feature a minimum fall directed towards the interior of the roof, generally set at a minimum of 2%, or even 3% depending on the chosen metal. This slope prevents standing water under the sheet metal and directs run-off onto the waterproofing rather than staining or damaging the building's exterior facade.
How far must the coping apron overlap the waterproofing upstand?
The hem or drip edge of the metal coping must extend vertically over the upstand by at least 50 mm beyond the line of mechanical top fixing, for standard parapets up to twenty metres in height. In locations exposed to strong winds or on tall buildings, this protective overlap is increased to block capillary rise.
Texts and standards cited
- norme SIA 271Waterproofing of flat roofs, terraces and green roofs, design and execution requirements for upstands and junctions
- CO art. 365Materials and site conditions: immediate notice to the client if the site, materials, or circumstances jeopardise the execution of the work
