Skip to content
Website
🧱 CFC 226Protection, green roofs and accessible roof terracesChapter 2 of 10 in the section

Root-resistant protection: a requirement, not an option, and how to prove it

Faced with the biological stresses of green roofs, standard waterproofing is punctured within a few seasons by rootlets and rhizomes. This chapter details the selection of membranes certified according to standard SIA 271, the continuous welding method for laps, the systematic treatment of peripheral upstands, and the preparation of technical evidence to be included in the as-built documentation for the client.

Key takeaways

  • Every green roof requires an upper waterproofing layer with formally certified root resistance.
  • Standard SIA 271 requires this protection across the entire surface as well as on all upstands.
  • Sheet welds and junction details are the areas most vulnerable to root punctures.
  • Test certificates and technical data sheets for membranes must be included in the as-built documentation handed over to the client.

Mechanics of root penetration and certification requirements according to standard SIA 271

Plant roots exert a combined mechanical and biochemical destructive action on waterproofing. In their permanent quest for water and mineral salts, rootlets exploit the slightest irregularity, microporosity or bonding defect in sheet laps. Once inside the gap, their radial growth generates considerable pressure capable of forcing apart defective welds, delaminating textile reinforcements and puncturing conventional bituminous masses lacking specific protective agents. This risk of degradation is by no means limited to intensive roofs planted with shrubs or species with spreading rhizomes: a standard extensive roof, composed of hardy sedums, wild grasses and mosses, develops a dense root system that penetrates an ordinary, non-certified bituminous membrane in less than three to five years. The resulting leak remains very difficult to locate without stripping large areas of vegetation.

Comparison of waterproofing solutions in contact with a green roof build-up
Membrane typeResistance mechanismCertification requirement
Root-resistant elastomeric bitumen (SBS)Chemical root-resistant additives within the bituminous massTest certificate according to European standard or FLL guideline
Synthetic (FPO / TPO / PVC-P)Homogeneous mechanical resistance of the polymer resinManufacturer's specific root-resistant approval
Standard untreated bitumenNone (inevitable puncture under vegetation)Non-compliant for green roofs according to SIA 271
Root resistance certification
Official certificate issued by an accredited independent laboratory, validating that a membrane and its welded joints have resisted aggressive root attacks from test plants without puncturing during a controlled greenhouse testing protocol of two to four years.

The waterproofer must strictly distinguish a simple water-resistant waterproofing from a waterproof system with root resistance certified according to recognised protocols. A thicker membrane or the addition of an extra standard bituminous cap sheet provides no immunity against the puncturing action of rootlets. Only membranes incorporating active inhibiting agents within the bituminous mass or composed of tested homogeneous synthetic resins prevent biological penetration. A filtering geotextile fleece or a drainage mat in no way constitutes a recognised root barrier.

Rigorous execution of welds, treatment of upstands and supporting documents for the as-built documentation

  1. Preparation of overlapsThoroughly clean, dry and degrease overlap areas. The minimum weld width must reach 80 mm longitudinally and 100 mm at roll ends, eliminating any soil debris or mineral dust before jointing.
  2. Continuous welding and fusion inspectionHeat continuously with a torch or hot air to achieve an even bleed of liquid bitumen of approximately 5 mm along the edge, or fuse synthetic sheets by heat-welding, checking soundness using a metal seam probe.
  3. Treatment of angle filletsInstall bridging strips and preformed gussets on all internal and external corners, executed exclusively with the same root-resistant certified membrane as the main area to maintain an unbroken barrier.

Peripheral upstands and roof penetrations are the most vulnerable points of a green flat roof. Roots preferentially colonise edge zones where the substrate remains sheltered and damp. According to standard SIA 271, the root-resistant membrane must extend up parapets, upstands and service penetrations to exceed the finished level of soil or gravel by at least 150 mm. This height ensures that vegetation cannot cross the barrier through layering or surface overgrowth. The top of the upstand requires mechanical clamping with a clamp bar and metal flashing strip injected with a weather-resistant mastic.

Under art. 365 CO, the contractor is liable for the sound quality of the materials supplied. On a structure under a green roof, this liability requires recording physical proof of compliance directly in the as-built documentation handed over to the client upon handover. This technical file must include the product's CE declaration of performance, the official certificate of root resistance issued by an independent body, the self-inspection protocol for welds using a seam probe, as well as detail drawings of penetrations and parapet upstands. Without these formal supporting documents, the durability warranty of the work cannot be certified against risks of water ingress.

Details, upstands and sterile margins: ensuring root-resistant continuity

On a green flat roof, failures due to root punctures very rarely occur within the main sheet area. Almost all damage arises from a breach of continuity at geometric junctions: upstands on kerbs and parapets, rainwater outlets, service ducts and expansion joints. Roots and rhizomes exploit the smallest microscopic weld discontinuity, drawn to the coolness and residual moisture that naturally collect against hollow sections and internal corners. According to standard SIA 271, the waterproofing system must provide an unbroken barrier against root penetration across the entire surface in contact with vegetation or exposed to rhizome growth, which includes all vertical upstands extending above the finished soil level.

Critical connections and root barrier continuity according to standard SIA 271
DetailRoot stressInstallation ruleWeld treatment
Rainwater outletMajor root attraction towards the damp low pointFlange with sleeve welded to underside and mesh gravel guardContinuous weld and double reinforcement treated root-resistant as a collar
Parapet upstandRoot ingress over the top of the upstand and under flashingExtension above finished substrate and mechanical clampingRoot-resistant treated upstand sheet fully bonded and welded
Pipe penetrationGrowth along smooth pipe wallsFitted prefabricated sleeve with stainless steel clamping collarPeripheral weld onto main membrane with suitable mastic bead
Expansion jointPenetration of taproots into the expansion voidFlexible elastomeric waterproofing strip arranged in an omega profileContinuous vulcanisation or heat-welding along joint edges

Self-inspection of welds, preliminary tests and documents for the as-built documentation

The waterproofer assumes direct liability for the integrity of the root barrier until the work is handed over to the landscaper or the structural work contractor. Once the drainage layer, filter fleeces and cubic metres of growing medium are poured onto the roof, any repair becomes extremely cumbersome and expensive, requiring complex excavation work to locate a millimetric breach. Under art. 365 CO, the contractor is liable for the sound quality of the materials supplied. For the waterproofer, this duty of diligence implies installing no product without an official root-resistance certificate and verifying the flawless execution of joints before any covering.

  1. Mechanical check of overlaps with a seam probeThe foreman inspects all longitudinal and transverse welds using a blunt seam probe. The tool is run with constant pressure along the lap edge to detect the slightest bonding defect or unwelded capillary. Any separation requires reworking with a torch or hot air.
  2. Waterproofing test by water retention or tracer gasBefore laying any drainage layers, a waterproofing test is carried out to verify the complete absence of punctures. On flat roofs with zero or low pitch, temporary water retention with blocked outlets validates overall performance. Alternatively, testing using smoke or tracer gas beneath the membrane instantly reveals micro-defects in joints.
  3. Joint inspection record before covering with vegetationA joint inspection record is drawn up and signed with site management and the external works contractor. This document confirms the complete visual and technical integrity of the root-resistant waterproofing and formalises the transfer of risks before greening machinery is moved across.

The meticulous preparation of the as-built documentation handed over to the client provides final proof of compliance with CFC 226 trade standards. This documentation must compile the manufacturer's declaration confirming the certified root resistance of the membrane, the declaration of conformity with the requirements of standard SIA 271, the technical data sheets for sheets and joint mastics, as well as as-built drawings detailing the executed upstands and penetrations. If water ingress occurs several years later due to root growth from aggressive plant species unsuited to the initial design, these supporting documents unequivocally establish the waterproofer's compliance upon handover of the work.

Managing non-conformities and remedies in the event of root damage

When a visual inspection or a preliminary waterproofing test reveals a lack of lap adhesion, or if the installed bituminous or synthetic material lacks certified root resistance according to standard SIA 271, corrective action must be taken without delay before spreading any gravel or mineral substrate. Once the green roof build-up has been installed by the landscaper, the cost of manual clearance, soil removal and complete refurbishment turns a simple workmanship defect into a major loss for the waterproofer.

  1. Formal notice to the clientAs soon as a membrane non-conformity or weld damage is identified, the waterproofer informs site management. Art. 365 CO al. 3 notes that if any circumstance compromises the proper or timely execution of the work, the contractor must inform the client immediately. This written notice technically protects the tradesperson against the aggravation of damage by other trades.
  2. Cutting out and remediation of the areaOn an operational green roof, the area affected by root penetration is cleared using a round shovel to protect the substrate. The punctured sheet is cut open, the puncture cleaned and dried, and the embedded rhizomes are removed mechanically without chemicals harmful to rainwater runoff.
  3. Installation of a certified reinforcement patchThe waterproofer applies a root-resistant membrane patch extending at least 150 millimetres beyond the critical point. Heat-welding or solvent-welding is performed according to factory instructions, followed by systematic checking of the lap edge using a seam probe and the application of a liquid sealant bead.
  4. Updating the as-built documentationRepairs, photographs of remedial work prior to covering and certificates of conformity for replacement materials are appended to the as-built documentation handed over to the client.

Documentary traceability is the waterproofer's sole defence in the event of subsequent disputes. Incorporating these supporting documents into the as-built documentation certifies compliance with Swiss trade standards and governs the validity of waterproofing warranties against root attacks.

Frequently asked questions

Can a simple geotextile fleece be installed to protect standard waterproofing against roots?

No, standard non-woven or woven geotextile never stops rootlets. Roots easily penetrate it under osmotic pressure and subsequently puncture the underlying bituminous or synthetic waterproofing. Standard SIA 271 expressly requires an upper waterproofing layer with certified root resistance according to recognised test protocols (FLL procedure or corresponding European standard), or the installation of a continuous, dedicated root barrier sheet.

Which waterproofing upstands must be covered with a root-resistant membrane?

All waterproofing upstands in direct contact with the substrate, filter layer or drainage zone must be treated with a certified root-resistant membrane. This applies to parapets, rooflight upstands, ventilation plinths and various penetrations. The root-resistant membrane must extend to the top of the upstand or project at least 100 millimetres above the finished surface of the topsoil or the peripheral sterile margin.

How should junction joints around rainwater outlets on a green roof be detailed?

Rainwater outlets are critical points when facing root attacks. The waterproofer must weld a flange made from the same certified root-resistant membrane as the main layer, with a minimum overlap of 150 millimetres. Around each drain, installing a leaf guard, a perforated inspection chamber and a 300-millimetre-wide washed round gravel sterile margin prevents roots from colonising the drainage outlet.

What proof must the waterproofer provide in the as-built documentation to discharge their liability?

To prove compliance with standard SIA 271, the contractor must submit to the as-built documentation: technical data sheets for the rolls certifying root-inhibiting additives or FLL-certified treatment, the as-built drawing specifying the installed membrane, self-inspection reports of welds using a seam probe, and waterproofing test records by water retention or tracer gas before the substrate is laid by the landscapers.

Texts and standards cited

  • SIA 271Building waterproofing - Specifications for green roofs and root resistance
  • CO art. 365Materials and site: the contractor is liable for the sound quality of the materials supplied; if materials supplied by the client or the ground designated by the client are found to be defective, or if any other circumstance compromises the proper or timely execution of the work, the contractor must inform the client immediately, or bear the consequences thereof (al. 3).

In the same section