Key takeaways
- The temperature and speed pair continuously adapts to humidity, wind and ambient heat.
- A destructive peel test is mandatory every morning on offcuts before welding the roof.
- Failure must tear the reinforcement weave or the material, never debond along the seam plane.
- Written traceability of settings protects the roofer by documenting the conformity of the seams according to recognised rules.
The temperature-speed pair facing roof weather variations
Thermal welding of flexible synthetic membranes, whether plasticised polyvinyl chloride (PVC-P) or thermoplastic polyolefins (TPO/FPO), relies on the controlled surface fusion of two surfaces in contact. This process requires introducing a continuous hot-air stream between the two sheets, immediately compressed by a silicone pressure roller. The operating window remains very narrow: a setpoint that is too high degrades the polymers, burns the polyester textile reinforcement or glass fleece, and creates irreversible carbonisation that weakens the waterproofing. Conversely, a temperature that is too low or an excessive travel speed of the automatic welder produces merely superficial adhesion. This precarious bonding deceives immediate visual inspection with a blunt probe but undergoes delamination during freeze-thaw cycles or under the action of wind.
The weather conditions prevailing on the roof slab continuously influence the thermal balance of the seam. Wind is the welder's primary disruptor: a gust deflects the jet from the flat nozzle and instantly cools the blown air before it penetrates the lap. Atmospheric humidity, morning dew or a cold substrate temperature create a significant heat dissipation effect, with the insulation system or substrate absorbing the heat energy. The roofer must then compensate for these losses by increasing the heat by 20 °C to 40 °C or by reducing the travel speed of the automatic welder. During the afternoon, the natural heating of the membrane under the sun requires the reverse approach in order to preserve the nominal thickness of the seam under the pressure roller.
| Membrane material | Welding process | Air temperature | Travel speed |
|---|---|---|---|
| Plasticised PVC (PVC-P) | Automatic welder | 450 °C to 520 °C | 2.0 to 3.5 m/min |
| Plasticised PVC (PVC-P) | Manual hot-air gun | 420 °C to 480 °C | Steady manual movement |
| Flexible polyolefins (TPO/FPO) | Automatic welder | 380 °C to 460 °C | 1.8 to 3.0 m/min |
| Flexible polyolefins (TPO/FPO) | Manual hot-air gun | 360 °C to 430 °C | Steady manual movement |
Morning peel test and traceability of seam parameters
No value predetermined in the workshop guarantees the conformity of a weld on the roof. Parameters validated the previous day are no longer accurate the following morning, because the outside temperature, wind and power supply voltage have varied. The destructive peel test must be carried out at the start of each working day on membrane offcuts before welding the first linear metre of roof. This check is also required after any extended stoppage, when changing membrane rolls or as soon as a noticeable weather change occurs.
- Preparation of test offcutsCut two strips of new, dry membrane approximately ten centimetres wide by forty centimetres long, taken from the rolls being installed.
- Welding the test seamMake the overlap seam over a minimum width of forty millimetres using the preselected temperature and speed settings.
- Cooling the seamWait for total dissipation of heat for at least five minutes until ambient temperature is reached, otherwise mechanical behaviour will be distorted.
- Cutting the stripsCut three strips five centimetres wide perpendicular to the weld line to prepare for mechanical tensioning.
- Tensile peel testPull firmly by hand or with pincers at one hundred and eighty degrees to force the seam open and examine the failure line.
Visual examination of the failure mode conditions the start of installation. The test is successful only when the failure is cohesive: the tear must destroy the plastic material or expose the internal textile reinforcement, without a clean separation between the two layers at the weld level. Conversely, interfacial debonding leaving two smooth, shiny surfaces demonstrates a cold weld; the temperature must be increased or the speed reduced. If the material yellows, blisters or flows excessively under the roller, overheating requires lowering the thermal output.
Under art. 364 CO, the contractor's liability is subject to the same rules as that of an employee. The roofer is liable for the diligent execution of the work by documenting each day the setpoint temperature, travel speed, ambient conditions and the result of the peel test in the site logbook. The cut strips are stapled to the self-monitoring sheet. This methodical traceability protects the company against hand-over disputes and guarantees the flawless hold of the seams against wind uplift and water ingress.
Peel test diagnostics and failure criteria
On a flat roof, the morning destructive check constitutes the only operational means of verifying that the plasticisation of the edges produces genuine homogeneous fusion without destroying the polymers. The interdiffusion of macromolecular chains requires a very precise heat input combined with mechanical pressing. For synthetic membranes made of plasticised PVC or FPO/TPO, the thermal window is narrow: too hot, the compound burns, smokes and loses its plasticisers; too cold, the simple superficial bonding peels off after a few months under the effect of frost and wind. This range varies according to the mass of the insulation and ambient humidity. The roofer joins two test strips of 30 cm by 15 cm cut from the rolls of the day. These coupons are welded directly on the thermal insulation of the construction site, never on a cold parapet flashing sheet.
- Tool preheatingPower on the automatic welder or manual gun for at least five minutes to stabilise the nozzle temperature and verify the cleanliness of the air blow openings.
- Welding the test specimenExecute a seam of at least 25 cm with the flat nozzle under the constant pressure of the silicone roller, checking for the appearance of a slight, regular bead.
- Complete coolingWait ten minutes for complete cooling to the core. A test on a lukewarm membrane produces false cohesion.
- Cutting the stripsCut three 50 mm strips perpendicular to the seam using a utility knife, leaving 30 mm free for gripping.
- Pulling to failureFold back the lips at 180 degrees and pull firmly until mechanical tearing of the specimen occurs.
| Observed failure mode | Diagnosis | Consequence | Correction |
|---|---|---|---|
| Clean peeling at the seam (adhesive failure) | Insufficient heat or excessive speed | Water infiltration at the first cold spells | Increase by 15 °C or slow down by 0.3 m/min. |
| Tear within the material (cohesive failure) | Complete macromolecular fusion | Watertight and durable seam under loads | Parameters validated for the morning. |
| Burning of the compound and blue smoke | Excessive heat or clogged nozzle | Brittle plastic and premature ageing | Lower by 20 °C and clean the nozzle. |
Thermal drift, voltage drops and settings traceability
Settings validated at dawn become obsolete as soon as the sun warms the membrane, or conversely when a cold wind sweeps across the flat roof. The blown hot air loses several tens of degrees between the heating element and the nozzle outlet as soon as the wind speed exceeds 20 km/h at the parapets. Temporary construction site electrical installations generate another frequent pitfall: voltage drops on long cable reels. If the supply voltage drops from 230 V to 205 V during the simultaneous start-up of a crane or a mixer, the thermal output plummets. On manual tools without closed-loop electronic regulation, this drop causes underheated welds that are undetectable without destructive testing.
- Perform a new peel test whenever there is a noticeable variation in sunlight or an increase in wind.
- Make a new test specimen after every extended work stoppage or change of site distribution board.
- Adapt the travel speed when transitioning from an area sheltered by a roof access housing to an exposed corner sector.
- Revalidate the setpoint settings when starting a new manufacturing batch of synthetic membranes.
The diligent execution of waterproof seams complies with recognised trade rules, synthesised notably in standard SIA 271. Art. 365 para. 3 CO provides that if the material supplied by the client or the ground designated by them is discovered to be defective, or if any other circumstance arises that compromises the proper or timely execution of the work, the contractor must immediately inform the client, under penalty of bearing the consequences. To prove the perfect conformity of their works, the roofer records the date, time, weather conditions, mains voltage, setpoint temperature and machine speed on their self-monitoring sheet each day. The strips from the destructive tests are dated and stapled to it to compile the handover file.
Shutdown and restart procedure during a non-compliant peel test
When the morning or intermediate peel test reveals adhesive failure, the welder stops work. A failure at the interface without decohesion of the plastic mass proves an unstable, merely thermal bond. Two causes dominate: insufficient heat input or excessive travel speed of the automatic welder. The setpoint temperature must be increased in increments of 10 °C to 20 °C, or the speed reduced by 0.2 m/min to 0.5 m/min. If the material exhibits blisters, browning or excessive expulsion of liquid material from the lap, the seam has burned: the reinforcement is weakened and the material is degraded. The thermal setpoint must then be lowered or the machine travel speed increased.
- Inspect the nozzle of the manual gun or automatic welder: remove carbonised plastic deposits with a brass brush to restore the airflow.
- Check the cleanliness of the silicone pressure roller: a dirty roller creates asymmetrical pressure and distorts seam compression.
- Measure the electrical voltage at the end of the site extension lead: a voltage drop under load prevents the heating element from reaching its setpoint temperature.
- Protect the working area from wind with a screen: a sudden breeze dissipates the hot air and cools the upper sheet before the roller passes.
Any corrected setting requires a new peel test on a sacrificial specimen made with the same synthetic membrane offcuts. Work on the main waterproofing area never resumes without a clean cohesive failure. The validated parameters (displayed temperature, speed in m/min, roller pressure force) as well as ambient temperature and sunlight conditions are entered in the welding logbook. In the event of persistent failure linked to a contaminated membrane batch or climatic conditions incompatible with the manufacturer's instructions, the site foreman applies the duty to notify under art. 365 CO to site management.
Frequently asked questions
At what time of day should the peel test be repeated?
The peel test is performed in the morning before the first metre of welding. It must mandatorily be repeated after every extended break, when moving from shade to direct sunlight, or if the wind suddenly picks up. An outdoor temperature swing of more than 10 °C alters the polymer's viscosity and requires a new thermal qualification specimen to recalibrate the waterproofing automatic welder.
Why does peeled TPO membrane sometimes tear away without leaving a mark?
This tearing away without material transfer indicates cold adhesive failure. The molecular chains of the two sheets did not interpenetrate. This defect stems from an air temperature that is too low, insufficient contact time under the nozzle or excessive roller speed. The roof appears closed on the day, but freeze-thaw cycles and shrinkage stresses will open the seam over the months.
How can the effect of cold wind on an automatic welding machine be compensated for?
Wind instantly dissipates heat between the two sheets before the pressing zone. To correct this loss, mobile windbreaks should be installed around the welding machine. If this is insufficient, the operator reduces the travel speed of the automatic welder rather than excessively raising the temperature, thereby avoiding charring the upper face of the synthetic membrane while maintaining the effective air volume.
What should be done if the electrical extension lead drops the power of the hot-air gun?
An extension lead that is too long or of insufficient cross-section creates a critical voltage drop. The heating element no longer delivers the programmed energy, distorting the actual temperature of the expelled air. Cables with a minimum cross-section of 2.5 mm² must be used, length must be limited to 25 metres, or automatic welders must be connected directly to a stably powered site distribution board, without accumulating energy-intensive equipment.
Texts and standards cited
- CO art. 365material and ground: immediate notification to the client if a circumstance compromises the regular execution of the work
- norme SIA 271Execution and inspection of flat roof waterproofing
