Skip to content
Website
🧱 CFC 226Membranes: bitumen, synthetic, laying and jointingChapter 2 of 10 in the section

Membrane welding: lap width and seam probe inspection

Mastering the jointing of waterproofing sheets requires adhering to precise lap widths and systematically checking every weld. This chapter details the methodical use of the seam probe on flat roofs according to standard SIA 271, detecting voids or lack of fusion, as well as compliant thermal repair protocols to ensure watertightness before water testing.

Key takeaways

  • Comply with the minimum longitudinal and transverse lap widths specified by standard SIA 271.
  • Inspect all welds with a rounded seam probe as soon as the joints have cooled down completely.
  • Immediately identify fusion defects with visible marking without puncturing the waterproof membrane.
  • Repair weak spots by torch or hot-air welding using an applied patch.

Lap widths and welding mechanics according to standard SIA 271

On a flat roof, jointing the sheets is the critical point of the waterproofing build-up. A membrane, whether polymer bitumen or synthetic, tolerates no dimensional guesswork during installation. Standard SIA 271 specifies the general execution principles to guarantee durable waterproofing against mechanical and climatic stresses. The lap width directly determines pull-out resistance under wind action and shear resistance caused by differential thermal movements.

Minimum lap widths according to standard SIA 271
Membrane typeLongitudinal lapTransverse lap (end lap)Fastening method / bridging
Elastomeric (SBS) or plastomeric (APP) bitumen80 mm to 100 mm100 mm to 150 mmTorch welding or hot bitumen with a visible bleed-out bead
Adhered synthetic material (PVC / TPO)60 mm to 80 mm80 mm to 100 mmWelding with a manual hot-air gun or guided automatic welder
Mechanically fastened synthetic material100 mm to 120 mm80 mm to 100 mmWidened lap to accommodate fastening plates clear of the weld

For bituminous membranes, proof of correct jointing is visually demonstrated by the extrusion of a regular 5 mm to 10 mm bitumen bead along the outer bevel. This bleed-out bead confirms that the underside and the overlap surface have reached the required melting temperature. For synthetic membranes, homogeneous hot-air fusion welding must display a controlled deformation mark without burning or scorching the plasticised compound.

Seam probe inspection protocol and repair of defects

Running the seam probe is the most elementary check, yet too often neglected on the construction site. It must be performed exhaustively on 100% of the welded length, without exception, after the material has cooled completely. A visual inspection is never sufficient: membrane edges may appear joined simply by superficial cold adhesion or pressing without having fused through the material. Art. 364 CO reminds us that the contractor is responsible for the diligent and faithful performance of the entrusted work; omitting this test directly engages their professional liability.

Seam probe
A rigid metal rod, right-angled or slightly curved, with a bevelled but blunt tip, designed to probe the free edge of a waterproofing seam under moderate manual pressure without damaging the membrane.
  1. Cooling periodAllow the weld to cool to ambient temperature. Probing a still-warm joint softens the material and creates false punctures.
  2. Tool guidancePosition the seam probe at an angle against the edge of the overlap, tilted at approximately 45 degrees, and slide the tool continuously along the weld line.
  3. Detection and markingApply constant pressure towards the interior of the joint. As soon as the probe penetrates an air pocket or a bonding defect, mark the start and end of the open area with grease pencil.
  4. Cleaning before repairRemove dust, moisture, and charred residue inside the uncovered pocket using a suitable solvent for synthetics or a scraper for bitumen.
  5. Thermal repairSlide the nozzle of the hot-air tool or soft flame to soften both inner faces, then press with a silicone roller or apply a patch extending 100 mm beyond the defect.

Construction site organisation requires this probing to be carried out at the end of each daily work stage. Running the seam probe over every linear metre before leaving the roof guarantees the temporary watertightness of the work. Postponing this operation increases the risk of closing up defects under site traffic or concealing critical defects beneath the thermal insulation or gravel layer.

Systematic inspection organisation and joint defect detection

On a flat roof, the visual appearance of a weld bead remains deceptive. A regular bead of molten bitumen or a uniform press line on synthetic membrane can mask mere superficial adhesion, without true molecular interpenetration of the material. The golden rule is to test every linear metre of joint with the seam probe before leaving the working area.

The test is never performed on a warm membrane. For elastomeric (SBS) or plastomeric (APP) bitumen, as well as for FPO or PVC synthetic sheets, the bead must be fully cooled and stabilised. Premature stress tears the warm material, deforms the edge, and skews the assessment by creating a false defect or concealing latent delamination.

Common anomalies detected during seam probe inspection
Mechanical findingCause on the construction siteImmediate consequence
Clear penetration of the probeCold weld, misdirected nozzle, travel speed too fastComplete break in watertightness, direct entry of residual water
Partial penetration with separationInsufficient rolling pressure with silicone or steel rollerShear weakness and progressive pull-out under wind action
Fraying or tearing of the edgePrior contamination by construction site dust, moisture, or talcLack of intimate bonding between the two membrane sheets
Penetration at T-jointOmission of corner chamfering on the underlying membraneCapillary action along the unflattened step

Marking non-compliant areas with grease chalk or a site pencil is done instantly during the run. The site foreman ensures that no section is signed off by visual inspection alone, including in areas cluttered with upstands, upstand details, or service pipe penetrations.

Repair methodology and remediation of defective welds

The discovery of a discontinuity requires a targeted intervention that varies according to the nature of the binder. Superficially heating the outside of a closed synthetic seam provides no internal fusion; it damages the glass fleece or polyester scrim reinforcement without restoring cohesion.

  1. Delimitation and opening of the defectSlide a clean spatula or the probe to pinpoint the exact extent of the debonding on either side of the open zone, until reaching a sound and completely homogeneous weld.
  2. Preparation of contact surfacesRemove infiltrated moisture, soot, or dust using a suitable dry cloth. On synthetic membranes, apply the reactivating cleaner recommended by the manufacturer to deoxidise the joint area.
  3. Thermal reheating and pressureFor short lengths without deep dirt ingress, insert the narrow flat nozzle between the two faces, heat until plastic softening occurs, and roll immediately from the inner joint outwards with the seam roller.
  4. Installation of a reinforcement patch (if contaminated or torn)Cut a round patch or reinforcement strip from the same membrane, with corners pre-rounded to a minimum radius of 50 mm, ensuring an overlap of at least 100 mm beyond the defective perimeter. Weld and retest after complete cooling.

Rigorous management of these steps guarantees compliance with standard SIA 271, which places the continuity of the waterproofing layer and the shear resistance of joints at the heart of execution requirements. Internal inspection reports record these daily verifications before the tinsmithing trade begins or heavy protection layers are installed.

Managing joint non-conformities and execution liabilities

The discovery of a clear defect during seam probe inspection or the finding of a lap width that does not comply with standard SIA 271 requirements requires an immediate response from the site foreman. Applying systematic inspection across the entire welded length allows lack of fusion to be caught before subsequent layers are laid. As soon as the onset of delamination or the absence of a continuous bitumen bead is identified, the area must be cordoned off immediately to prevent premature covering with thermal insulation or heavy protection.

  1. Marking and purging the sectionMark the exact length of the unwelded bead with a grease pencil, extending 100 mm on either side. Remove any contamination, water, or dust present in the gap.
  2. Rewelding or installing a cover stripReheat the defective area if the sheet has not been degraded, or apply a welded cover strip at least 150 mm wide centered on the joint.
  3. Final joint verificationRun the rounded seam probe cold over the repaired edges once more and record the intervention in the site log.

The waterproofer assumes technical responsibility for the overall watertightness of the structure. When executing a repair proves impossible due to a scorched membrane or contamination by construction site dust, stripping the section and replacing it completely remains the only compliant solution according to trade standards. In the event of a dispute over joint quality before installing gravel or decking, a water tightness test flooded for at least forty-eight hours or a vacuum bell test may be ordered by site management.

Frequently asked questions

At what specific time of day should the seam probe be run over the welds?

The inspection must strictly be carried out after the material has cooled completely, generally half an hour after using the torch or automatic hot-air machine. Testing a still-warm weld skews the diagnosis: the probe risks perforating the softened bitumen or giving a false impression of cohesion in an area where the compound has not set. The ideal procedure is to inspect each morning the surfaces welded the previous day.

What pressing force must the installer apply when running the seam probe?

The force must be moderate but firm, equivalent to a continuous manual pressure without jerking. The metal tip, which must be rounded so as not to shear sound material, should simply glide along the bevel formed by the overlap. If the weld complies with standard SIA 271, the probe butts against the bead without slipping in. As soon as the tool penetrates between the two layers, a defect is confirmed.

What should be done if the minimum lap width was not maintained during installation?

If a sheet drifts and exhibits a lap narrower than the value specified by standard SIA 271, the existing weld no longer ensures the structural reliability of the work. The waterproofer must then weld a reinforcement strip of the same material, with a minimum width of 150 to 200 mm, centred over the disputed joint. This preventive extra layer restores the required safety margins prior to work acceptance by the client's representative.

Why should unmodified sharp needles be refused on the construction site?

A sharp steel probe or a ground screwdriver that has not been rounded will score the edge of the membranes, particularly on flexible synthetic sheets. The operative risks mechanically prising open a sound edge by piercing the material instead of verifying the homogeneity of the weld bead. The compliant tool always features a rounded corner or a blunted hook shape to guide the motion without damaging the membrane texture.

Texts and standards cited

  • SIA 271Building waterproofing: design details, sheet lap widths, and joint inspection criteria on flat roofs.

In the same section