Skip to content
Website
🧱 CFC 226Upstands and special detailingChapter 4 of 10 in the section

Penetrations: sleeve, welded flange and distance between two penetrations

On a flat roof, every penetration constitutes a critical weakness for the structure. This chapter guides you through the geometric dimensioning and execution of penetrations: compliance with minimum waterproofing heights, choice between prefabricated or site-fabricated flanges, and maintaining the clearances essential for torch or hot-air welding.

Key takeaways

  • Standard SIA 271 requires a minimum upstand height of 150 millimetres above the waterproofing.
  • A minimum horizontal clearance of 150 millimetres is mandatory between two separate penetrations.
  • The distance between a penetration and the edge of a parapet upstand must reach at least 200 millimetres.
  • Prefabricated sleeves with a wide flange ensure seamless continuity with the bridging strip.

Waterproofing height and installation of the sleeve on the pipe

Any ventilation pipe, solar collector bracket or cable duct passing through the waterproofing system creates a mechanical discontinuity in the drainage plane. According to standard SIA 271, the basic rule requires that the waterproofing upstand rise vertically against the pipe to a height of at least 150 mm above the wearing course or the top level of the heavy surfacing (gravel, paving slabs). In areas particularly exposed to snow accumulation or at high altitudes, this freeboard value must be increased to 200 mm, or even more depending on the assessment of climatic stresses.

Effective detailing of this specific point relies on the use of a rigid flange or a prefabricated sleeve compatible with the membrane of the system (SBS elastomeric polymer bitumen, APP plastomeric bitumen, or synthetic material such as TPO/FPO or PVC). Metal sleeves (copper, stainless steel or plastic-coated metal sheet) must have a horizontal flange at least 100 mm to 120 mm wide to ensure optimum adhesion of the successive layers. If the pipe passes through the thermal insulation without an independent sleeve, the risk of internal condensation and shearing under the effect of differential thermal movements becomes major.

  1. Installation of the base layer and vapour barrierTightly connect the vapour barrier to the pipe at the structural support level by applying a connection sleeve to block any migration of interstitial moisture into the insulation.
  2. Insertion of the rigid sleevePlace the sleeve or waterproofing collar over the pipe, resting flat on the first layer of the field waterproofing, which has been previously cleaned and degreased.
  3. Welding of the flangeFully torch-weld the horizontal flange to the reinforcement strip, then cover it with the second membrane layer, ensuring a joint offset of at least 100 mm.
  4. Mechanical fastening and top sealTighten a stainless steel clamp with a rot-proof sealing gasket at the top of the bituminous or synthetic upstand, then cap the assembly with a metal rain collar.

Minimum distances between penetrations and clearance from upstands

The primary cause of water ingress at penetrations does not stem from the material itself, but from poor coordination on the construction site, which leads to grouping pipes within excessively confined spaces. It is physically impossible to execute a watertight weld using a torch or a hot-air gun if the nozzle, seam roller or scraper cannot move freely around the pipe. As soon as two pipes touch or are separated by less than 100 mm, the flat roofer is forced to apply mastic or makeshift resins, which rapidly degrade under ultraviolet radiation.

Geometric safety clearances for waterproofing welds
Geometric configurationMinimum clear distanceExecution constraint
Between two insulated pipes150 mmPassage of the welding nozzle and complete perimeter seam rolling
Between pipe and parapet upstand200 mmOverlap of the bridging strip and connection to the flashing
Between pipe and rainwater outlet500 mmSump area and connection of the outlet flange
Between pipe and edge of an expansion joint500 mmStructural movements and volume of the expansion bellows

To comply with the requirements of standard SIA 271, the site foreman must reject penetrating openings that are positioned too closely as early as the preparation of the structural work and tinsmithing drawings. When dense clusters of building services (refrigeration lines, solar cables) must pass through the roof system in a restricted space, individual penetration via multiple small pipes must be avoided. The proven technique consists in grouping all services through a shared upstand kerb waterproofed like a continuous upstand, capped with a removable cover and a downward-facing gooseneck pipe.

The area between the base of the parapet and the perimeter of the sleeve also requires specific attention. The waterproofing upstand against the parapet wall includes a horizontal toe of at least 100 mm to 150 mm on the field area. If the penetration is located less than 200 mm from the wall, the overlaps of the vertical upstand and the horizontal collar directly clash, creating a build-up of four to five membrane layers. This accumulation prevents the drainage of residual water and increases the risk of welding defects at internal corners.

Installation of the sleeve and welding of the waterproofing flange

Every soil and waste pipe, soil stack vent or technical conduit passing through a flat roof constitutes a critical discontinuity in the membrane. Standing or running water constantly subjects these detailing points to stress. To eliminate any risk of capillary ingress or wind-induced peel, the connection requires a flange or collar bonded to the horizontal waterproofing plane, extended by a sleeve fitted to the cylindrical pipe. The use of factory-prefabricated sleeves, industrially produced and identical to the waterproofing system used, guarantees an irreproachable thermal bond with the cap sheet.

  1. Continuity of the vapour barrier at the baseBefore laying the thermal insulation, fit the vapour barrier tightly around the emerging pipe. Form an airtight and vapour-tight collar using dedicated adhesive tape or a compatible preformed piece in order to prevent interior moisture from rising into the insulation build-up.
  2. Fitting and welding of the collar to the waterproofingPosition the prefabricated sleeve over the pipe. Weld the perimeter flat collar to the first layer of waterproofing or in full adhesion between two bituminous layers. For synthetic membranes, carry out hot-air welding with systematic joint inspection using a blunt probe.
  3. Connection to the cap sheetLay the top finishing layer by cutting a neat circular cutout that overlaps the collar flange by at least 100 mm. Carefully smooth out the bitumen bead or press with a silicone roller to expel air pockets.
  4. Top termination and rainwater tightnessTrim the sleeve to the required height, at least 150 mm above the heavy surfacing or gravel. Fit a stainless steel clamping band with an ultraviolet-resistant elastomeric sealant underneath, or cover the top with a metal rain collar secured to the pipe.

Spacing clearances, clustered penetrations and technical coordination

The reliability of flat roof waterproofing depends on the freedom of movement available to the flat roofer when handling tools. Torch-welding a bituminous collar or hot-air welding a synthetic membrane requires a minimum geometry around each pipe. If the pipes are installed too close to one another or directly against masonry, the seam roller and welding nozzle cannot pass through. This results in hidden lack of adhesion, which is an inevitable source of defects and leaks.

Minimum working clearances for connecting penetrations
Geometric configurationMinimum clear distanceSite execution constraint
Between two adjacent pipes or penetrations300 mmPassage of the pressure roller, complete welding of the collar without damaging overlaps of the flanges.
Between a penetration and an upstand (parapet, wall)300 mmInstallation of the waterproofing angle fillet reinforcement, installation of termination profiles and mechanical fastening of the system.
Between a penetration and a rainwater outlet500 mmClearance around the drainage sump, connection of the gutter flange and unobstructed gravity drainage.

When sanitary, electrical or ventilation installations bundle several service pipes together without observing the 300 mm spacing, individual sleeving is technically impossible. Standard SIA 271 then requires grouping the pipes inside a shared masonry upstand kerb or an insulated metal box. This kerb forms a continuous perimeter waterproofing upstand rising at least 150 mm above the wearing layer, topped with a removable cover ensuring rainwater shedding with a drip edge.

In accordance with art. 365 CO, the contractor informs the client whenever any circumstance compromises the proper or timely execution of the work. If the flat roofer notices openings in the slab that are positioned too close together or against walls, they must immediately issue written notification to the site management prior to installing any insulation, in order to have the layout modified or to secure the installation of a compliant kerb.

Managing layout clashes and remedying non-conformities

On the construction site, the flat roofer regularly encounters penetrations drilled outside tolerances: plumbing pipes tight against a parapet wall, service conduits separated by less than 150 mm, or pipe ends too low to achieve the required height. Proceeding under these conditions without formal objection engages the direct liability of the company. As soon as a penetration prevents the passage of the torch or hot-air nozzle, or hinders the tightening of a mechanical clamp, installation must be suspended in the affected area.

  1. Inspection and formal notificationMeasure actual centre-to-centre distances and document deviations from the execution drawings. In accordance with art. 365 CO, the contractor immediately informs the client or the site management when any circumstance compromises the proper or timely execution of the work, formally stating the impossibility of guaranteeing watertightness in accordance with standard SIA 271.
  2. Correction of physical interfacesRequire plumbing or electrical contractors to extend penetrations to provide a minimum of 150 mm above the finished wearing course, or to group services within a shared opening with an insulated metal kerb, allowing a clear perimeter connection.
  3. Validation of the remedial solutionIf moving the pipe proves impossible, install a prefabricated junction box filled with a two-component liquid resin compatible with the roofing membrane, subject to written acceptance from the site management and the system supplier.

No penetration may be concealed beneath inverted roof insulation or gravel ballast without thorough visual inspection of the weld bead and the application of the top mastic seal beneath the stainless steel clamp. Waterproofing remains a continuous system in which every improperly detailed penetration compromises the entire roof.

Frequently asked questions

How should two soil pipes less than ten centimetres apart be treated?

Standard SIA 271 prescribes a minimum clear distance of at least 150 mm between pipe barrels to perform compliant welding of each collar. When this distance is lacking on the slab, fabricating individual bituminous or synthetic sleeves becomes impossible. The pipes must be grouped within a single waterproof sleeve, or the shared area must be enclosed in a closed metal box that is subsequently filled with a polyurethane or PMMA resin suited to the roof waterproofing system.

What is the minimum height required for a waterproofing sleeve on a flat roof?

The upstand of the prefabricated or custom-made sleeve must project at least 150 mm above the accessible surface or the top protective layer, in compliance with standard SIA 271. On gravelled or green roofs, this dimension is measured from the exposed surface of the gravel or the growing medium, and not from the bare waterproofing membrane, in order to prevent any temporary submersion caused by rainwater ponding.

Can a waterproofing sleeve be secured solely by bonding without a mechanical top clamp?

No. Even with an elastomeric sleeve perfectly heat-welded to the base flange, the upper section surrounding the vent pipe or technical conduit undergoes axial expansion and ultraviolet ageing. A flexible, durable waterproofing mastic seal must be applied at the top, immediately encircled and compressed by a stainless steel mechanical clamp to secure the assembly and prevent rainwater ingress.

What should be done when a penetration emerges too close to the parapet?

Standard SIA 271 requires a clear space of at least 150 mm between the outer edge of the pipe and the parapet upstand to allow execution of the welds. If the pipe is tight against the wall, the flat roofer must have the penetration moved before laying the insulation. In the absence of a technical agreement, constructing an upstand kerb forming a waterproofing upstand enclosing both the parapet and the conduit constitutes the only reliable technical solution.

Texts and standards cited

  • SIA 271Flat roofs: requirements for the design and execution of waterproofing, upstand heights and minimum spacing of penetrations
  • CO art. 365Materials and ground: the contractor is liable for the good quality of the materials they supply; if the materials supplied by the client or the ground designated by the client are found to be defective, or if any other circumstance compromises the proper or timely execution of the work, the contractor must immediately notify the client, on pain of bearing the consequences (al. 3)

In the same section