Skip to content
Website
🧱 CFC 226Protection, green roofs and accessible roof terracesChapter 1 of 10 in the section

Extensive greening: drainage, filter, substrate and suitable plants

This chapter details the rigorous layering of an extensive green roof over flat roof waterproofing according to standard SIA 271. You will learn how to design and lay the drainage layer, the filter fleece, and the suitable mineral substrate. You will know how to precisely calibrate the thickness of the growing medium based on load-bearing capacity and select the corresponding plant palette.

Key takeaways

  • Standard SIA 271 requires root-resistant waterproofing beneath any extensive roof greening.
  • The filter geotextile prevents clogging of the drainage layer by fine particles from the overlying mineral substrate.
  • A substrate thickness of eight centimetres is sufficient for sedums but limits more demanding grasses.
  • Gravel margins protect upstands and ensure rapid drainage of surplus rainwater.

From waterproof substrate to filter geotextile: the functioning of the drainage build-up

An extensive green roof never consists of spreading topsoil over a waterproofing layer. According to standard practice and the requirements of standard SIA 271, each component fulfills a specific mechanical or hydraulic function. The waterproofing build-up must imperatively resist root penetration, either through the incorporation of certified anti-root additives in the polymer bitumen or synthetic material, or through the installation of a dedicated root barrier sheet. Over this clean and formally inspected waterproofing, the first layer laid is a polypropylene or polyester mechanical protection fleece, with a minimum mass per unit area suited to construction site stresses. This mat protects the membrane against puncturing during the subsequent tipping of aggregates. Each sheet overlap must be carefully inspected before any covering, as investigating a subsequent leak beneath greening involves complex interventions.

  1. Laying of the mechanical protection and slip layerUnrolling directly onto the root-resistant waterproofing with a 10 cm overlap, without any penetrating mechanical fixings.
  2. Installation of drainage elementsInterlocking of dimpled drainage boards with upper perforations or uniform spreading of crushed clay brick or expanded lava.
  3. Unrolling of the non-woven filter fleeceCross-laying over the drainage with a clean overlap of at least 15 cm and turned up along edges and upstands.

The drainage layer ensures hydraulic continuity beneath the substrate. Preformed high-density polyethylene boards with water retention cups and overflow slots represent the most common solution in Romandy, as they combine low structural dead load with excellent flow capacity under load. When the design specifies a continuous mineral bed made of pozzolana or crushed brick, the aggregate thickness must be calculated to prevent any crushing under occasional maintenance foot traffic. The filter sheet immediately caps this drainage before placing the technical soil.

Mineral substrate and greening: thickness governs the longevity of the plant cover

The substrate for extensive green roofs is an engineered mix predominantly made of mineral components, comprising crushed tile, lava, pumice, expanded clay, and a strictly proportioned organic fraction, generally less than ten percent by volume. The use of standard topsoil or ordinary compost is prohibited: loose soil compacts, suffocates roots, clogs the geotextile filter, and dangerously overloads the structural slab in the event of water saturation. The choice of final substrate thickness dictates not only the dead load added to the structure, but also the plant palette capable of establishing sustainably without permanent automatic watering.

Correlation between substrate thickness, saturated load, and suitable vegetation
Effective thicknessAverage saturated loadSuitable plant typesInstallation method
6 to 8 cm80 to 110 kg/m²Creeping sedums, mosses, lichensCuttings sowing, plug plants
9 to 12 cm115 to 160 kg/m²Varied sedums, Carthusian pinks, wild chivesPre-cultivated mats, standard plugs
13 to 15 cm165 to 220 kg/m²Xerophilic grasses, rock perennials, thymesPot planting, combined seeding

Beyond plant survival, the site manager and the site foreman must check load compatibility with the civil engineer's calculation notes. The bulk density of the substrate must always be assessed at its maximum water capacity, meaning fully saturated following a heavy rainstorm. Distributing substrate using tipping skips or a crane requires a steady pace: stockpiling heaps on the roof before levelling creates point loads that risk exceeding the permissible strength of the underlying insulation build-up. Manual levelling is carried out with a rake while stepping backwards to avoid prematurely compacting the mix.

Suitability between effective substrate thickness and plant palette

The depth of the planting bed is not merely an aesthetic consideration: it dictates the available water reserve, the cushioning of thermal shocks on the membrane, and the botanical longevity of the build-up. On flat roofs, standard SIA 271 governs protective and wearing layers. For extensive greening, the mineral substrate must ensure water retention through capillary action whilst evacuating surpluses towards drainage without ponding. Organic matter content must remain strictly limited, between 5 and 10% by volume. An excessive proportion of humus causes compaction of the layer, clogs the geotextile filter, and encourages colonisation by pioneer weeds that choke the selected mat.

Technical correspondence between mineral substrate thickness, saturated load, and plant typology on flat roofs.
Substrate thicknessIndicative saturated loadSuitable plant paletteHydraulic behaviour and maintenance
60 to 80 mm80 to 115 kg/m²Pure sedums (Sedum album, acre, reflexum, spurium) as cuttings or plug plantsExtreme drought resistance. No watering after establishment. Low, close-cropped plant cover.
80 to 120 mm115 to 160 kg/m²Sedums combined with pioneer grasses (Festuca ovina) and wild pinksIncreased water retention, enhanced thermal protection of the membrane, annual maintenance weeding.
120 to 150 mm160 to 210 kg/m²Diversified dry meadow: stonecrops, Dianthus, Allium, wild thymes, and grassesHigh evapotranspiration, dense biomass requiring an annual autumn mowing and removal of cuttings.

The planting method influences the work schedule and the rate of establishment. Sedum cuttings, spread manually at a rate of 50 to 80 g/m² over a rolled and moist bed, offer rapid installation but remain exposed to wind erosion during the initial weeks. The use of plug plants (15 to 20 pots per square metre) ensures uniform establishment on edges subject to wind turbulence. Hydroseeding with a cellulose binder is suitable for large, uniform areas. When substrate thickness falls below 60 mm, summer heat scorches the shallow root system, baring the filter fleece and exposing the waterproofing build-up to severe temperature swings.

Installation of gravel margins, outlets, and roof safety

Installing the greening build-up requires a strict separation between the planted zone and drainage outlets or upstands. According to standard SIA 271, waterproofing upstands against parapets, rooflights, and technical penetrations must be surrounded by a non-combustible gravel margin at least 300 mm wide. This strip of washed round gravel (16/32 mm grading), free of fine particles, blocks root growth towards fixing profiles, prevents wind uplift of upstands, and acts as a perimeter fire break.

  1. Filter overlap and profile installationCheck the continuity of the filter fleece over the drainage trays or boards. Sheets must overlap by at least 150 mm. Dry-lay the gravel-guard separation angles and position the inspection chambers over the rainwater outlets.
  2. Controlled substrate distributionDeliver the mineral substrate by crane in big bags or by pneumatic blowing from the silo truck. Avoid any point accumulation in the middle of spans and immediately spread heaps to comply with the permissible load limit defined by the civil engineer.
  3. Levelling and light compactionRake the mineral mix smooth, allowing an extra 10 to 15% in thickness to compensate for natural settlement after watering. Run a light roller to close the surface without crushing the drainage cups.
  4. Saturation watering and seedingSaturate the bedding layer with water to moisten the drainage and settle the aggregate matrix, then proceed without delay with hydroseeding or spreading sedum cuttings.

Operationally, handling heavy bulk materials on a flat roof involves strict health protection and accident prevention rules. When tipping edge gravel and grading substrate near the roof edge, the team applies the safety measures defined in art. 41 OTConst whenever the fall height exceeds 2 metres. The roofer ensures that a compliant perimeter guard rail or catch scaffolding is in place before starting to unload skips.

Corrective actions for drainage or plant cover defects

On a flat roof, defects related to extensive greening almost always result from a breach in the functional continuity of the layers or an incorrect choice of materials. If water ponds persistently above the fleece or if the sedum cover dies back from root rot, the roofer must immediately check the drainage layer and the permeability of the filter geotextile. Opening the inspection chambers located over rainwater outlets constitutes the initial diagnostic step: persistent standing water reveals either an obstruction by fine sediments or mechanical crushing of the dimpled drainage boards.

  1. Localised core sampling of the build-upManually excavate the substrate using a plastic shovel down to the crowns of the drainage board to inspect the water saturation state and the fouling level of the filter mat.
  2. Grading and load-bearing capacity checkMeasure the residual thickness of the mineral mix after natural settlement. An excessive proportion of fines or organic matter quickly clogs the fleece pores and suffocates roots.
  3. Clearing and replacing sheetsRemove clogged materials, carefully rinse drainage cups with low pressure, lay clean filter geotextile with a fifteen-centimetre overlap, and replenish with compliant mineral substrate.

When the installed substrate thickness is less than contractual tolerances, the vegetation cannot survive the summer heat or severe frosts of Romandy. Immediate top-up with pozzolana or calibrated expanded shale is necessary prior to any seeding. Furthermore, if protective gravel margins of at least 30 centimetres have been omitted along waterproofing upstands, the roofer must reinstate these washed round gravel barriers without delay. This perimeter detail ensures access to flashing terminations, prevents combustible material accumulation against facades, and safeguards rainwater outlets from any unwanted root colonisation.

Frequently asked questions

What is the minimum substrate thickness to ensure sedum establishment?

According to recognised trade standards and standard SIA 271, the minimum mineral substrate thickness for extensive sedum greening is 8 centimetres after settlement. Below this value, the water reserve is insufficient to survive summer drought periods in Romandy without supplementary watering. A thickness of 10 to 12 centimetres remains recommended to stabilise rooting and sustain a durable plant diversity including mosses and grasses.

Can site-stripped topsoil from the construction site be used on the flat roof?

No, ordinary topsoil is prohibited on flat roofs because it contains too high a proportion of clay and organic matter. Under rainfall, fine particles are washed down by leaching and clog the geotextile filter fleece, turning the build-up into an asphyxiating marsh. Standard SIA 271 recommends specific porous mineral substrates composed of crushed brick, pumice, or expanded shale to ensure permanent drainage.

What is the purpose of the gravel margin along edges and upstands?

The gravel margin of washed round gravel with a 16/32 grading, at least 30 centimetres wide, fulfills three major functions. It prevents plant roots from reaching vertical waterproofing details, stops flame spread towards facades or rooflights during dry periods, and facilitates the rapid drainage of surface water towards rainwater outlets. It also allows roofers to access upstands without trampling or damaging the plant cover.

How can waterproofing punctures be avoided during drainage and substrate installation?

Membrane protection begins with laying a heavy synthetic protection fleece, of at least 300 grams per square metre, before unrolling drainage elements. On the construction site, workers use wheelbarrows with pneumatic tyres over timber boarding tracks that distribute loads. Blowing the substrate from a silo truck or craning using bottom-discharge skips limits any aggressive direct contact with the waterproof substrate.

Texts and standards cited

  • SIA 271Building waterproofing: requirements for flat roofs, falls, drainage layers, filters, and greening.
  • CO art. 365Material and site conditions: the contractor is liable for the sound quality of the material they provide; if material provided by the client or the ground designated by them is found to be defective, or if another circumstance jeopardises the regular or prompt execution of the work, the contractor shall immediately inform the client, under penalty of bearing the consequences (para. 3).

In the same section