Skip to content
Website
🧱 CFC 226Membranes: bitumen, synthetic, laying and jointingChapter 4 of 10 in the section

Mechanically fastened membrane: layout of sheets and wind uplift resistance

This chapter details the setting-out method for mechanically fastened waterproofing membranes on flat roofs. You will learn how to size the width of the sheets to cover the stress plates, distribute the fastener density according to wind exposure, and carry out the work in accordance with a layout drawing approved by the technical office.

Key takeaways

  • Fastening under laps ensures wind uplift resistance without piercing the exposed membrane.
  • The approved layout drawing determines the orientation of the sheets and the pitch of the fasteners.
  • The width of the sheets is reduced at perimeters and corners to absorb wind suction.
  • Tightening the screws keeps the plate flat without puncturing the insulation or the membrane.

Organising fastening under laps and adjusting sheet widths

In a single-ply or two-ply waterproofing system mechanically fastened on a flat roof, each fastener must imperatively be located within the longitudinal lap area of the sheet. This technical arrangement conceals the anchoring line beneath the subsequent layer and guarantees the overall watertightness of the structure without having to resort to systematic cover strips. The stress plate, whether metallic or synthetic with a thermal break, clamps the waterproofing sheet and the thermal insulation against the load-bearing element made of concrete, timber, or profiled steel decking.

To ensure a continuous weld or seam in accordance with the requirements of Swiss waterproofing standards, the lap geometry requires millimetre precision. The screw axis is positioned at a minimum distance from the free edge of the lower membrane, generally set at ten to fifteen millimetres from the edge of the plate. The overlap of the upper sheet must then cover the entirety of the stress plate while reserving a consistent weld bead width, without thermal or mechanical degradation of the fused area.

Indicative lap dimensions according to fastener type
Fastener typePlate diameter or widthMinimum required lapMinimum weld width
Round metal plate40 mm100 mm40 mm
Oval or oblong plate40 x 82 mm120 mm40 mm
Telescopic plastic tube50 mm120 mm40 mm
Continuous perforated bar30 mm110 mm30 mm

The choice of the nominal sheet width directly conditions the efficiency of the construction site. In the central zone of a flat roof, where air suction remains moderate, using wide two-metre rolls optimises installation output by reducing the linear length of joints to be welded. Conversely, when uplift loads increase, keeping two-metre sheets would require spacing the fasteners so closely together that the membrane reinforcement could tear during storm gusts.

To overcome this constraint without multiplying through-fasteners across the middle of the panel, the site foreman reduces the usable sheet width. The roofer installs half-sheets of one metre or third-sheets of sixty centimetres along critical zones. This geometric reduction doubles or triples the number of anchoring lines available on the roof while keeping each fastener concealed and protected beneath the welded edge of the adjacent sheet.

Calculating density by wind zone and applying the execution drawing

Flat roofs are subject to asymmetrical suction forces generated by aerodynamic turbulence. According to standard SIA 261 and the recognised rules of the trade laid down for CFC 226, a roof is strictly subdivided into three distinct sectors: the field or central zone, the perimeter edge zone, and the corner zone. These last two undergo vortices that multiply the uplift force compared to the centre of the building.

The contractor cannot improvise the density or centre-to-centre spacing of fasteners on the construction site. Execution requires an approved layout drawing, prepared by the designer or the system supplier's technical office after load calculations according to recognised technical rules. This drawing specifies the orientation of the sheets relative to the ribs of the metal deck or concrete beams, the dimensions of the perimeter strips, as well as the precise number of screws per square metre for each zone.

  1. Substrate inspection and zone markingMark the boundaries of the corner and perimeter zones on the insulation with chalk according to the dimensions on the approved drawing. Check the type and thickness of the substrate to adjust the usable length of the screws.
  2. Unrolling and aligning the sheetsUnroll the membranes parallel or perpendicular to the substrate ribs according to the layout. Respect the relaxation time of the material before any final fastening.
  3. Setting out and screwing at the prescribed pitchPosition the plates under the lap, strictly respecting the calculated centre-to-centre spacing for the zone concerned. Use a screwdriver equipped with an adjustable depth stop.
  4. Lap welding and mechanical testingCarry out the thermal welding of the seam immediately after fastening. Perform testing with a dry point or seam probe after complete cooling to verify adhesion.

On the construction site, the foreman ensures that the insulation thickness is perfectly accommodated by telescopic tubes or self-drilling screws of adequate length. A screw that is too short will not provide the pull-out resistance required by the design calculations, while an overdriven fastener compresses the thermal insulation and forms a depression that traps runoff water directly over the anchoring edge.

Site setting-out and alignment of fasteners under laps

The success of a flat roof waterproofed with a mechanically fastened membrane relies on accurately transferring the approved layout drawing onto the site. The CFC 226 roofer must chalk out the installation guidelines as soon as the substrate is accepted, whether it is profiled steel decking, a reinforced concrete slab, or a timber deck. On steel decking, the primary rule dictates laying the sheets perpendicular to the deck ribs in order to distribute the uplift loads across all the upper flanges of the ribs, thus avoiding anchoring a continuous line of screws into the same rib.

Fastening edge under lap
Longitudinal marginal zone of a synthetic or bituminous membrane sheet receiving the line of mechanical fasteners (screws and stress plates), dimensioned so that the adjacent sheet fully covers these components and allows a continuous waterproof weld width of at least 30 to 40 mm beyond the plates.

In a standard configuration with a synthetic membrane, the lap geometry leaves no room for improvisation. The stress plate, whether oblong or circular with a diameter of 40 to 50 mm, must be installed at a precise distance from the free edge of the lower membrane, generally 10 to 15 mm from the edge of the sheet. The remaining space on the lap is used to develop the hot-air thermal weld strip. If the plate encroaches upon the fusion zone, the waterproof seam creates a direct leak path to the screw head, ruining watertightness.

  1. Checking axes and marking outCheck the dimensional conformity of the roof against the execution drawing approved by the site management. Strike the first perimeter line with a blue chalk line, deducting the parapet drop and the upstand allowance.
  2. Unrolling and relaxing the first sheetUnroll the synthetic or bituminous membrane along the marked axis. Allow the material to relax to eliminate residual coiling tensions before any final fixing.
  3. Drilling and anchoring under lapsInstall telescopic fasteners or self-tapping screws with metal stress plates at the strict centre-to-centre spacings defined by the calculation zone. Keep the driving tool strictly perpendicular to the substrate.
  4. Lapping and homogeneous weldingRoll out the next sheet, completely covering the line of plates. Proceed with hot-air welding (automatic welder or manual hot-air gun) after carefully cleaning the lap strip.

Modulation of sheets by wind zone and detailing of penetrations

Wind uplift loads are not exerted uniformly on the waterproofing: maximum negative pressures concentrate on roof corners and perimeter edges, whereas the central zone (field zone) experiences lower suction. The approved layout drawing incorporates this load distribution by modulating either the usable width of the sheets or the linear spacing of the screws within the lap edges. To comply with the mandated densities without overloading a single line to the point of tearing the reinforcement, the preferred technical solution along edges and corners consists of reducing the width of the sheets.

Example of synthetic membrane layout according to wind uplift zones
Roof sectorNominal sheet widthAverage fastener centresResulting densityLap principle
Central zone (field)1.50 m or 2.00 m250 mm to 300 mm2.2 to 2.8 screws / m²Concealed fastening in single edge, 120 mm lap
Perimeter zone (edge)0.75 m or 1.00 m (half-sheet)200 mm to 250 mm4.0 to 5.5 screws / m²Narrow sheets to multiply continuous anchoring lines
Corner zone (high suction)0.50 m or 0.75 m (third-sheet)150 mm to 200 mm6.5 to 9.0 screws / m²Closely spaced lines under lap or localised reinforcements

The use of full 2.00-metre sheets in corner zones must be avoided because it would require spacing the screws at centres closer than the minimum permitted by the substrate (risk of rupturing the thermal insulation board or excessive deformation of the steel decking). By cutting the roll into one-metre half-sheets or directly ordering rolls of suitable width, the installation crew doubles the linear length of fastening edges, which disperses the uplift load over twice as large an attachment surface while keeping all screws protected beneath the welded seams.

  • Drawing compliance: no change in sheet width or centre-to-centre spacing may be decided unilaterally on the construction site without the written consent of the engineer or responsible designer.
  • Roof penetrations: around curbs, smoke vents, and rooflights, vortex uplift forces require a line of reinforcing fasteners positioned 200 mm from the trimmer, systematically covered with a heat-welded membrane strip.
  • Roll end laps: transverse laps (butt ends of sheets) must be staggered by at least 500 mm from one line to the next to avoid ever superimposing four layers of membrane at the same point.
  • Substrate quality: pursuant to art. 365 CO al. 3, if the material supplied by the client or the ground designated by him is found to be defective, or if another circumstance compromises the regular or punctual execution of the work, the contractor must immediately notify the client; this applies directly upon discovering corroded steel decking or concrete that cannot be drilled.
  • Edge protection: in accordance with art. 23 OTConst al. 1, a perimeter guardrail must be used in unprotected locations where the fall height exceeds 2 metres, thus securing installation work along the most heavily loaded perimeters.

Managing setting-out deviations and mechanical fastening non-conformities

On a flat roof, a layout error or anchoring defect directly compromises resistance to wind uplift. If the actual centre-to-centre spacing between fasteners exceeds the values prescribed by the approved layout drawing, or if the delivered sheet width does not match the wind zone breakdown, the crew must immediately stop unrolling the membrane to prevent blow-off under negative pressure.

  • Alignment deviation or insufficient lap: if the edge of the adjacent sheet does not cover the stress plate by at least 40 mm beyond its outer edge, the line is declared non-compliant. Welding a joint over an exposed metal washer is prohibited.
  • Pull-out resistance lower than calculations: if a screw strips in steel decking or a screed-to-falls crumbles, the fastening under the lap is ineffective. Site pull-out tests must be carried out to recalculate the number of fasteners per linear metre.
  • Inappropriate widths: along edges or at corners, when the density per wind zone requires spacing that is impossible to achieve on a standard two-metre sheet, the roofer must slit the material or install narrow sheets dedicated to these perimeter strips.

When the load-bearing substrate exhibits undulations, deformed sheets, or heterogeneous concrete preventing compliance with the calculated spacings, the site management must be notified in writing. Pursuant to art. 365 CO, if the material supplied by the client or the ground designated by him is found to be defective, or if another circumstance compromises the regular or punctual execution of the work, the contractor must immediately notify the client. Rectifying a defective anchoring line requires either the addition of intermediate plates recalculated by the technical office, or the systematic bridging with a welded membrane cover strip applied with heat on either side of the stray fastener.

Frequently asked questions

How do you correct a mechanical fastener installed too close to the sheet edge?

If the screw or its stress plate intrudes into the usable weld zone, the assembly no longer provides the minimum joint watertightness. The roofer must then unscrew or countersink the defective fastener, reposition a correct fastener maintaining the safe distance under the lap, and then cover the entire affected area using a sleeve or a fully welded cover strip overlapping by at least 150 mm.

What should be done if the appropriate sheet width is missing on the construction site for perimeter edges?

The density per wind zone dictates an increased number of fasteners per square metre along edges and at corners. If the narrow sheets specified in the layout are missing, the crew slits a standard sheet lengthwise using a roofer's knife. The fasteners are aligned along the new edge, and the joint is then executed in strict compliance with the minimum welded lap according to manufacturer recommendations.

Why is it forbidden to alter screw spacings without technical recalculation?

Fasteners withstand wind uplift loads defined in accordance with standard SIA 261 and the roof geometry. Increasing the centre-to-centre spacing between two fasteners under laps reduces the overall storm resistance of the waterproofing system. Any modification from the approved layout drawing requires prior approval from the technical office or membrane manufacturer, under penalty of peel failure caused by progressive tearing.

How should you react when a screw passes through the insulation and spins freely in the substrate?

A screw that spins freely provides zero mechanical pull-out resistance. The operative must never leave an ineffective fastener beneath the subsequent sheet. It must be extracted, the penetration in the vapour control layer sealed with suitable mastic if accessible, and a new anchor or a screw of larger diameter installed at least 50 mm away from the old hole, in accordance with recognised technical rules.

Texts and standards cited

  • SIA 261Actions on structures (definition of wind loads and negative suction pressures on flat roofs)
  • SIA 271Waterproofing of buildings (provisions for the design and installation of flat roof membranes)
  • CO art. 365Defective material and ground: contractor's obligation to inform the client immediately if circumstances compromise execution

In the same section