Skip to content
Website
🧱 CFC 226Drainage and hydraulic safetyChapter 8 of 10 in the section

Drainage through the parapet: fall, sleeve, and connection to the downpipe

When routing pipes inside the building is impossible, rainwater drainage must pass through the parapet. You will learn how to set the fall of the core drilling, integrate the penetration sleeve into the waterproofing system, connect the flange to the upstands, and prevent the risk of frost blockage towards the external hopper.

Key takeaways

  • The opening or core drilling in the parapet must guarantee a minimum downward fall towards the exterior.
  • The prefabricated sleeve with a flexible flange is integrated with full adhesion between the two waterproofing layers.
  • The metal or synthetic flange must be mechanically clamped and connected with a neat waterproofing chamfer.
  • The risk of freezing requires a self-regulating heating cable or an appropriate thermal offset.

Setting out the penetration, drainage fall, and installation of the flanged sleeve

When rainwater downpipes cannot be integrated inside the building, the waterproofing installer must penetrate the parapet wall. This technical situation is frequently encountered during renovation work or on roofs situated above high-finish spaces that lack service shafts. The masonry opening, whether formed as a cast recess or diamond core drilled, requires a continuous downward fall of 2% to 3% towards the exterior. The absence of a fall or the presence of a low point encourages residual water ponding within the structure, accelerates fouling by mineral dust, and compromises the durability of the waterproofing membranes. The prefabricated sleeve must pass through the insulation and the wall without any sagging.

  1. Cleaning and primingThoroughly remove dust from the drilled opening, remove concrete laitance, chamfer the entry edge, and coat the surfaces with a suitable bituminous primer.
  2. Geometric setting of the pipeInsert the rigid stainless steel or copper sleeve, then adjust its mechanical packing to ensure a fall of at least 2% without lateral play.
  3. Integration of the first layerConnect the first layer of the waterproofing upstand under the sealing flange, avoiding any excess thickness likely to impede the natural flow of water at the base of the valley.
  4. Welding of the upper membraneWeld the upper waterproofing membrane over the previously degreased metal flange, ensuring a welded, watertight overlap of at least 150 mm all around.
Geometric criteria and setting-out tolerances for parapet penetrations
Geometric parameterMinimum technical thresholdGood practice rule
Fall of the penetration pipeContinuous 2% towards the outsideAvoid any low point or internal backfall
Connection flange width120 mm minimumContinuous weld between two waterproofing layers
External projection of the spigot80 mm beyond finished wallFree entry into the hopper without bonding
Offset at the throat invert0 mm (flush with the finished face)Prevent residual water ponding on the roof

External facade connection, hopper, and frost protection

On the facade side, the penetration pipe exits beyond the external face of the masonry and the external wall insulation system. This connection must never be rigid or bonded: structures undergo mechanical deformations, settlement, and contrasting temperature variations. The waterproofed pipe must project by 80 to 100 mm to enter freely into a suspended hopper installed by the tinsmith. This loose, telescopic engagement accommodates thermal expansion and eliminates any backflow behind the facade render. A rain collar completed with a bead of elastomeric sealing mastic provides a watertight seal between the cast-in sleeve and the penetration pipe.

The critical issue with parapet scuppers lies in their high thermal vulnerability. Unlike internal vertical outlets that are kept tempered by the heated interior of the building, the lateral spigot is exposed to sub-zero outdoor temperatures over its entire length. During sunny winter periods, snow on the roof melts slowly due to daytime solar radiation or slab heat loss. As soon as this meltwater reaches the cold metal opening of the sleeve, it freezes instantly into solid ice. This accumulation blocks drainage, causes abnormal hydraulic loading on the roof, and endangers the top edge of the waterproofing upstands.

  • Installation of heat tracing using a self-regulating heating cable inserted into the spigot and connected to an ambient thermostat.
  • Continuous thermal insulation around the penetration body across the entire thickness of the parapet using a rock mineral wool pipe section.
  • Selection of a rectangular or circular sleeve cross-section that is oversized compared to normal flow calculations.
  • Mandatory installation of an independent emergency overflow set at a distinct height on the same parapet section.

On high-altitude construction sites or those subject to prolonged frost, installing a temperature sensor linked to a humidity controller ensures the heating cable activates automatically only when water is present, limiting energy consumption while preventing system blockage.

Multi-layer connection at the parapet upstand

When rainwater drainage cannot be provided via an internal downpipe, the parapet penetration concentrates mechanical and thermal stresses at the roof's most vulnerable point. The waterproofing installer must ensure a continuous joint between the angle fillet, the waterproofing upstand, and the flange of the through-sleeve. Any unevenness under the flange creates a local backfall or an excess thickness that traps debris, promoting water ingress under prolonged hydrostatic head during backflow events.

  1. Substrate preparation and recessingSlightly recess the thermal insulation or patch the concrete screed at the penetration to conceal the thickness of the connection flange. The flange must sit flush with the supporting substrate to avoid any water ponding upstream of the orifice.
  2. Application of the bonding primerCoat the concrete substrate and the metal flange (degreased stainless steel, copper, or lead) with a cold-applied bituminous primer or the proprietary bonding primer recommended for synthetic membranes.
  3. Welding the first upstand layerSandwich the flange between the first waterproofing layer of the main roof field and the first angle strip of the upstand. The flange must have a collar of at least 150 mm around the entire perimeter of the through-pipe.
  4. Installation of the cap sheet and bridgingFully weld the SBS elastomeric bitumen cap sheet or synthetic membrane with a minimum overlap of 120 mm beyond the perimeter of the flange, ensuring proper feathering of the edges to expel trapped air.
Assembly methods for the through-sleeve according to the waterproofing system
Waterproofing systemSleeve materialJointing techniqueOn-site check
Two-ply elastomeric bitumen (SBS)Milled lead (2.5 mm thickness) or sandblasted stainless steelPreheating the flange, torch bonding between first layer and cap sheet, full bitumen bleed-out jointing.Check with thermal tracker to ensure no overheating, and verify an even bitumen bleed-out of 5 to 10 mm along the edge.
Synthetic membrane (FPO / TPO)Rigid FPO collar or compatible laminated metal sheetManual hot-air welding in two passes (tack welding then final seam) using a 20 mm flat nozzle and silicone pressure roller.Mechanical check of the weld seam with a blunt probe after complete cooling.
Reinforced liquid applied resin (PMMA / PU)Stainless steel flange or abraded synthetic sleeveMechanical sanding, solvent degreasing, installation of a saturated polyester reinforcement fleece between two coats of resin.Dry film thickness measurement and visual inspection for complete saturation of the fleece without air voids.

External continuity, thermal protection, and functional checks

The connection on the external face represents the second critical area of the assembly. The penetration spigot must project past the outer face of the parapet wall or render by at least 80 mm, entering freely into the centre of the hopper or chute. Parapet thermal bridging requirements dictate that the annular gap between the core hole and the drainage pipe must be insulated: a penetration pipe in direct contact with concrete creates a severe thermal bridge that accelerates freezing of residual water inside the conduit.

  • Continuous fall of the penetration: Maintain a minimum outward slope of 3% to 5% to accelerate gravity drainage and prevent thin films of water from standing inside the wall.
  • Sleeve and perimeter insulation: Insert a closed-cell elastomeric foam insulation sleeve around the pipe inside the core hole, then seal the ends with a neutral elastic waterproofing mastic.
  • Self-regulating heating cable: In mountain areas or on parapets heavily exposed to north winds, install a thermostatically controlled self-regulating trace heating cable housed beneath the waterproofing strip or inside the drainage sleeve.
  • Downpipe decoupling: Leave a gap of at least 20 mm between the bottom of the spigot and the base of the hopper to accommodate differential movement without stressing the waterproofing upstand.

Before signing off the penetration, the team carries out a sectional water test upstream of the parapet. The operative checks that there is no water retention flush with the flange, inspects the discharge path into the hopper, and checks the watertightness of the underside of the penetration. In accordance with art. 365 CO, if the initial core hole has a backfall or an inadequate diameter that compromises the sleeve's insulation, the contractor must notify the client before permanently securing the waterproofing.

Remediation of defects: backfall, lateral infiltration, and freezing

Defective workmanship on a lateral parapet outlet rapidly leads to severe damage within the structure and the thermal insulation system. Discovering standing water at the base of the fillet or water ingress on the slab soffit frequently points to a backfall in the sleeve or tearing of the waterproofing collar under stress from the upstand.

Diagnosis of parapet penetration defects and corrective actions
Observed defectTechnical cause on siteImmediate remedial action
Water backflow at the upstandZero or reversed penetration fall during core drillingStrip back the system, realign the sleeve with a minimum downward fall towards the exterior, and reinstate the waterproof connection
Moisture in the upstand insulationPoorly welded flange or bridging torn by thermal expansionRemove upstand detailing, install a new sleeve with double collar and chamfered reinforcement patch
Blockage by freezing on the facadeAbsence of heating cable or through-wall thermal bridgeInsulate the sleeve within the masonry and install a self-regulating trace heating tape connected to the hopper

If the core drilling performed by the mason slopes inwards, the waterproofing installer must not attempt to rectify the fault simply by building up layers of bitumen or liquid resin. Article 365 CO requires that the client be notified as soon as any circumstance compromises the proper execution of the works. Remediation requires patching the bedding layer with non-shrink mortar or re-drilling the hole to re-establish a continuous minimum fall of 2% towards the outside.

In the event of recurring freezing in the parapet throat, the remaining insulation thickness around the metal pipe often proves insufficient. The waterproofing installer must then locally strip back the assembly to fit a continuous, high-performance thermal insulation shell and coordinate the installation of electric trace heating with the electrician before closing up the upstand layers in accordance with the rules of standard SIA 118.

Frequently asked questions

How can a parapet core hole drilled horizontally without an outward fall be corrected?

Forcing the sleeve into place by distorting the waterproofing is prohibited. Two technical solutions must be considered: either re-drill the lower part of the hole with a core drill to create a downward fall of at least 2% towards the facade, or install a sleeve of the next smaller diameter bedded in a tapered resin mortar bed, verifying that the calculated hydraulic capacity remains strictly sufficient.

What solution should be adopted if the sleeve flange crosses a bituminous vapour control layer and then the upper upstand?

The waterproofing installer must ensure watertightness at two distinct levels. The penetration through the vapour control layer receives a first collar welded to a flange or a bead of compatible mastic. Then, above the thermal insulation, the final penetration sleeve is sealed into the upper waterproofing system with its own fully bonded flange, preventing any interstitial moisture migration within the parapet insulation.

Why must the external hopper not be soldered directly to the penetration sleeve?

The hopper and the external downpipe undergo significant thermal expansion and belong to the tinsmithing trade. If the penetration pipe is soldered rigidly to the hopper, thermal movements will tear the internal waterproofing flange. The waterproofing installer's sleeve must slide freely inside the hopper inlet with sufficient expansion clearance and a weathering flange.

What should be done when an ice plug frequently blocks drainage within the wall thickness?

Water accumulation in a concrete parapet rapidly cools the metal sleeve passing through the perimeter insulation. The only durable solution consists in inserting a self-regulating heating cable into the scupper, connected to an external temperature sensor. The waterproofing installer must also verify the presence of an insulation shell at least 20 mm thick around the pipe and clean the leaf guard to prevent residual water ponding.

Texts and standards cited

  • SIA 118General conditions for construction works
  • CO art. 365Materials and site conditions: the contractor is liable for the sound quality of the materials they supply; if the materials supplied by the client or the ground designated by the client are found to be defective, or if any other circumstance compromises the proper or timely execution of the work, the contractor shall immediately inform the client, failing which they shall bear the consequences (para. 3)

In the same section