Skip to content
Website
🧱 CFC 214Timber connections, ironmongery and fastenersChapter 7 of 10 in the section

Punched metal plate truss: never recut, never drill

Punched metal plate trusses form a statically indeterminate system where each chord and web operates under very high stress ratios. This chapter details the handling rules, nail plate anchorage limits under standard SIA 265 and the technical reasons why any modification on the construction site irreversibly destroys structural integrity.

Key takeaways

  • Any recutting of timber or perforation of a bottom chord voids the manufacturer's structural calculations.
  • The anchorage of nail plates relies on the integrity of the steel teeth pressed into the timber.
  • Standard SIA 265 mandates strict compliance with verified cross-sections and connections.
  • Horizontal storage without continuous blocking causes irreversible out-of-plane buckling deformations.

Mechanical behaviour of nail plates and strict prohibition of alterations

Punched metal plate truss roofs rely on the precise sizing of softwood timber sections, assembled using punched metal nail plates. In this structural system, the timber members operate primarily in axial tension or axial compression combined with bending. Force transfers from one member to another without traditional flitching or mortise and tenon joints: the entire load passes through the metallic nail plates. According to standard SIA 265, connections with metallic fasteners must guarantee strength and stiffness consistent with the static models adopted during engineering design.

Punched metal nail plate connector
Galvanised or stainless steel plate featuring integral teeth produced by mechanical stamping, pressed into both faces of the timber under a hydraulic press in the workshop to form the structural connection of a joint.

The efficiency of a joint depends strictly on the plate anchorage area on each intersecting member, full tooth penetration and compliance with edge and end distances. When an installer makes a saw cut to fit a wall plate bearing, shorten an eaves overhang or chamfer a top chord, they cut away the timber volume contributing to shear resistance and to the holding power of the perimeter teeth. This cut immediately reduces the contact area below certified design values. Similarly, drilling through a bottom chord to run a pipe, ventilation duct or electrical conduits removes part of the net effective cross-section subjected to pure tension. The overall load-bearing capacity drops abruptly.

The ban on recutting or drilling admits no exception. The carpenter cannot manually alter a prefabricated element without compromising the stability of the roof. In the event of a dimensional error in the supporting masonry, adaptation must be addressed by lateral bracing, manufacturer-approved structural bearing shims or a full replacement order, never by trimming the prefabricated trusses.

Storage, handling and lifting rules to prevent out-of-plane buckling

A prefabricated truss displays substantial in-plane vertical inertia, but extreme flexibility perpendicular to its plane prior to the installation of permanent bracing and anti-buckling ties. This low transverse stiffness exposes the structure to high risks of irreversible geometric deformation if guidelines for transport, ground storage and lifting are not rigorously observed upon arrival on the construction site.

  • Vertical storage on flat, stable ground, leaning against a support frame with regular spacing battens.
  • Horizontal storage permitted only in tidy stacks, resting on timber blocks perfectly aligned beneath each joint node.
  • Continuous weather and rising-damp protection using a ventilated tarpaulin preventing water retention.
  • Immediate removal of standing water to prevent wood fibre swelling around pressed metal teeth.
  1. Slinging preparationUse a rigid spreader beam with multiple textile slings distributed along the rafters, avoiding any direct hitching to connector plates or to a single central point.
  2. Lifting and up-rightingRotate the truss from its resting position without mechanical jolts, maintaining a slinging angle that avoids excessive lateral deflection of the bottom chord.
  3. Installation and temporary stabilisationPlace the truss on the wall plates and immediately secure temporary diagonal bracing battens, the temporary ridge line and spacing ties before releasing the slings.

When lifting takes place without a suitable spreader beam, transverse forces generate severe twisting in the truss. This out-of-plane buckling causes pull-out or partial loosening of the metal teeth embedded in the timber. Even a displacement of a few millimetres in the connectors compromises stress transmission and ruins compliance with standard SIA 265.

Force transfer to supports and absolute preservation of heel joints

In a prefabricated truss structure, the heel joint concentrates the most severe stresses in the structure. The junction between rafter and bottom chord simultaneously transfers vertical shear to the bearing and the horizontal pure tension component balancing the slope triangulation. According to standard SIA 265, the design of this joint is based on the direct anchorage of the pressed metal plate teeth into the solid wood thickness, with zero mechanical play or residual cutting margin.

Tensile forces absorbed by the bottom chord frequently reach several tens of kilonewtons at ULS (ultimate limit state). The teeth of the stamped plate penetrate the timber to a depth calibrated in the workshop under a hydraulic press. Any reduction in the timber cross-section or any notch weakening the bearing edge creates stress concentrations perpendicular to the grain, causing immediate longitudinal splitting under climatic loads (snow or wind).

Direct structural consequences of heel joint alterations
Observed alterationDirect mechanical consequenceStandard and contractual impactPermitted corrective action
Chamfering the bottom chord heelLoss of tooth anchorage area and splitting initiationTotal non-compliance under standard SIA 265Full truss replacement or engineer-approved flitching
Notching for wall plate clearanceInterruption of continuity in compressed rafter fibresCritical exceedance of axial compression stress ratioInstallation prohibited; element rejected upon delivery
Drilling through the bottom chordReduction of the net area working in tensionBrittle failure under axial tension during overloadsMandatory written approval from timber engineering office
Partial grinding of the nail plateConnector shear and loss of rotational stiffnessLoss of factory warranty and conformity markingImmediate removal of the degraded component

Technical interfaces and protocols in the event of dimensional discrepancies

Running building services (controlled mechanical ventilation ducts, plumbing lines, flues) and loft access create severe stresses on bottom chords and diagonals. No secondary trade is permitted to core, notch or rebate the members of a prefabricated truss. If a trimmer opening or flue passes through the roof plane, the opening must be planned upstream during industrial procurement by fabricating a calculated, factory-assembled trimmer frame.

If the materials provided by the employer or the ground designated by him are found to be defective, or if any other circumstance compromises the regular or timely execution of the work, the contractor shall immediately inform the employer thereof, failing which he shall bear the consequences (para. 3).

art. 365 CO

When the site foreman notices a dimensional discrepancy on the masonry tops or supporting wall plates, they must never force the timber by bending or recut the frame to level it out. Compensating for uneven levels or span deviations must strictly take place beneath the truss, by inserting non-rot distribution shims under the wall plate or adjusting the concrete bearing pad.

  1. Inspection and suspension of fixingHalt installation as soon as a geometric conflict or bearing defect exceeds permitted erection tolerances (generally 10 mm on the contact length).
  2. Formal notification to the site agentDocument the structural work geometric non-conformity in an inspection report with photographs and precise survey measurements.
  3. Consultation with the engineering officeSend the as-built survey to the competent technical office to obtain an approved compensation solution using supplementary steel brackets, bearing shims or calculated timber flitches.
  4. Execution of the approved modificationInstall only the reinforcement components specified in the revised drawing signed by the timber structural engineer responsible for the project.

Management of non-conformities and site liabilities

On a timber construction site, discovering a geometric clash or damage on a prefabricated truss requires an immediate halt to all work on the element. The temptation to notch a bottom chord for duct clearance or cut off a rafter heel to offset out-of-plumb masonry constitutes a severe structural alteration. Sizing under standard SIA 265 relies on the full cross-section of the timber and the precise anchorage of the metal connectors. Any unauthorised cut reduces load-bearing capacity below design load levels.

  1. Identification and securingHalt installation immediately upon discovering a dimensional clash or a pulled-out connector during lifting. Erect temporary propping under adjacent joints if the component is already slung or partially connected.
  2. Formal notice of interruptionImmediately notify the site management and the appointed timber engineering office in writing. Art. 365 CO al. 3 provides that if any circumstance compromises the regular or timely execution of the work, the contractor shall inform the employer.
  3. Manufacturer technical assessmentForward millimetre-accurate records of the defect to the manufacturing plant. Only the technical office holding the original static model can specify an approved repair using through-bolted steel plates or order the manufacture of a replacement truss.

Strict enforcement of this procedure protects the safety of the erectors and clears the carpenter's civil liability. Any unauthorised modification directly engages the installer's criminal liability. Art. 229 CP punishes with a custodial sentence of up to five years or a monetary penalty anyone who, when directing or executing a construction project, intentionally breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons.

Frequently asked questions

A nail plate has detached slightly during unloading: can it be hammered back in with a sledgehammer?

No, this practice is strictly prohibited. The metal teeth are calibrated for smooth hydraulic pressing in the workshop. Manual hammering bends the anchoring claws, tears the longitudinal wood fibres and reduces the bearing area required by standard SIA 265. If a connector has lifted by more than one millimetre, the truss must be quarantined pending assessment by a timber engineer or return to the manufacturer.

A ventilation pipe crosses the centreline of a load-bearing bottom chord: is clean core drilling acceptable?

No drilling is permitted in the timber of a prefabricated truss, regardless of the tool used. The bottom chord acts in pure tension or combined tension-bending depending on the triangulation. Drilling the member reduces the net cross-section and can shear zones under internal stress. Technical services must be routed between two trusses, or accommodated by a dedicated trimmer opening designed and calculated in advance by the specialist technical office.

The masonry is 20 mm out of plumb at the bearing: can the rafter be chamfered?

It is strictly forbidden to recut the rafter heel or the bottom chord end. This joint concentrates the support reaction and transfers major shear stresses to the wall plate. Reducing the timber removes the minimum cover depth of the nail plate connector. The structural work tolerance must be made up using an incompressible hardwood or steel bearing shim, sized to guarantee the code-required bearing area.

A bundle of trusses was exposed to rain on the construction site: does wood swelling threaten the connections?

Excess moisture causes differential swelling that forces the connector outwards and starts to dislodge the teeth. If timber moisture content exceeds 20 %, the anchorage capacity calculated under standard SIA 265 is compromised. Trusses must be stored vertically, raised 30 cm off the ground and protected by a ventilated tarpaulin to avoid any out-of-plane distortion or premature corrosion of the galvanised steel plates.

Texts and standards cited

  • SIA 265Timber structures - Design rules and requirements applicable to punched metal plate fastener joints.
  • CO art. 365Materials and ground: the contractor immediately informs the employer if any circumstance compromises the regular or timely execution of the work (para. 3).
  • CPBreach of the rules of the building art: whoever, when directing or executing a construction or demolition project, intentionally breaches the rules of the trade and knowingly endangers the life or physical integrity of persons is liable to a custodial sentence of up to five years or a monetary penalty; if committed through negligence, up to three years or a monetary penalty.

In the same section