Key takeaways
- Collective fall protection is required as soon as the fall height exceeds two metres.
- Art. 41 OTConst specifies the edge restraint measures required according to roof pitch.
- Above a sixty-degree pitch, work is carried out exclusively from suitable equipment.
- Mobile elevating work platforms replace direct access to very steep roof slopes.
Determine the critical fall height and apply art. 41 OTConst
During cutting, hoisting, or installing purlins and rafters, the risk of toppling into the void constitutes the predominant hazard for timber framing teams. Working at the roof edge requires strict constructive provisions as soon as the working level presents an unprotected void. Swiss regulations harmonise these requirements in order to prevent serious accidents during the erection phases of the load-bearing structure.
Fall height measurement is evaluated from the carpenter's working plane — whether it is the wall plate, the ridge, or the rough joist floor — down to the ground outside or to the underlying receiving surface. According to art. 41 OTConst, appropriate measures to prevent falls must be taken from a fall height of more than 2 m. For the carpenter, this requirement dictates anticipating edge restraint as soon as the first structural elements are installed.
| Observed fall height | Required protection device | Implementation by the carpenter |
|---|---|---|
| Less than or equal to 2.00 m | Organisational measure or cordoning off | Guiding components from the ground, work without mandatory perimeter restraint |
| Greater than 2.00 m | Collective edge protection | Temporary perimeter edge protection fixed to the frame or restraint bracket |
| Greater than 3.00 m | Façade scaffolding or heavy-duty restraint | Coordination with erection contractors to accommodate eaves overhangs |
Within the framework of a works contract, foremen must coordinate the progress of timber works with the collective measures in place. If independent perimeter edge protection is used on a timber structure, its dimensions must meet recognised technical criteria: top rail positioned at least one metre high, intermediate rail, and toeboard to prevent tools or connecting components from slipping off.
Adapting devices according to pitch and using elevating platforms
The inclination of the slopes radically alters the physics of a fall. On a moderate pitch, a worker who stumbles slides down the rafters before hitting the edge; on a steep pitch, the trajectory resembles an almost instantaneous free fall. Traditional edge protection rails or simple brackets then become ineffective in cushioning or stopping a person in motion.
- Roofs with a pitch of less than 25 degrees: maintenance of standard edge protection or a suitable rail at the eaves.
- Roofs with a pitch between 25 and 60 degrees: obligation to insert specific catch devices or protective barriers to arrest sliding.
- Roofs with an inclination greater than 60 degrees: prohibition of moving directly on roof slopes to erect timber framing.
For the installation of complex dormers, spires, Mansard roof kerbs, or church roofs whose rafters exceed this limiting inclination, using a mobile elevating work platform (MEWP) becomes the reference solution. This equipment ensures that the carpenter handles structural components from a closed and stable basket, eliminating fall-restraint forces into the void.
- Verifying machine seatingPosition the elevating platform on stable ground, outriggers deployed on timber spreader plates, assessing soil bearing capacity around the building.
- Approaching the installation planeMove the basket as close as possible to the kerb line or raftering to limit any overhang when fitting mortise and tenon joints.
- Bolting and anchoring from the basketPerform truss pinning or sprocket bracket fixing without ever stepping over the basket guard-rail to bear onto the inclined timber frame.
Using an elevating platform requires rigorous planning of the operating area, coordinated with crane hoisting of structural timbers. The daily cost of hiring and operating a self-propelled platform is in the order of 400 to 900 CHF per workstation, an essential investment to integrate from the price estimation stage for steep works.
Implementing perimeter protections on timber framing during the hoisting phase
During the assembly of timber frames and trusses, the fall threshold dictates rigorous advance planning even before timber components are brought in by crane. As soon as the fall height exceeds 2 m, erectors cannot work on wall plates or purlins without a continuous physical device. Temporary edge protections fixed directly to the timber structure must be installed on the ground onto prefabricated elements or immediately after provisional bracing of the first bay.
Anchoring edge protection posts to load-bearing timber requires specific fixings adapted to restraint loads. Steel brackets screwed to principal rafter ends or clamped onto verge rafters must meet the strict geometric requirements of the construction work ordinance to prevent a worker from falling over the edge.
On low-pitch roofs, below 25°, setting up rigid perimeter edge protection along eaves and gable verges is sufficient to contain the risk of stepping off the edge. Conversely, as soon as the inclination exceeds this first threshold, the dynamics of a slide prohibit the use of a simple rail: the body accelerates down the inclined plane and slips beneath the rail or breaks it upon impact. Safety nets under the roof structure or full internal decking become indispensable to cover the void beneath the roof throughout the assembly of purlins and rafters.
- Fitting verge brackets and uprights directly on the ground onto edge rafters prior to crane hoisting.
- Locking the three protective elements: top rail at least 100 cm high, intermediate rail, and toeboard.
- Systematic verification of the centre-to-centre distance between posts to prevent excessive guard-rail deflection under dynamic loads.
- End-to-end joining of protective barriers between eaves edge and gable verges without corner discontinuities.
Pitch transitions: selection of access equipment and technical limitations
Pitch radically alters the carpenter's balance conditions and the trajectory of moving masses. Beyond 25° and up to 60°, the risk of uncontrolled sliding precludes the exclusive use of standard eaves edge protection. A roof catch scaffold or restraint scaffolding equipped with a solid wire-mesh screen becomes the required collective means to intercept a fall sliding down the slope.
| Roof pitch | Worker behaviour | Permissible collective device | Prohibited practice |
|---|---|---|---|
| Up to 25° | Autonomous balance possible on elements | Perimeter edge protection fixed to verge rafters or purlins | Absence of toeboard at the edge |
| Over 25° to 60° | Rapid sliding upon loss of grip | Roof catch scaffold or safety net below the slope | Simple perimeter edge protection without protective barrier |
| Over 60° | Foot support impossible, suspension required | Mobile elevating work platform or full working platform | Direct progression on the frame, roof catch scaffold alone |
When the inclination exceeds 60°, the carpenter can no longer maintain their position on the framing by simple mechanical grip. At this degree of slope, no working platform attached to the slope or guard-rail allows the application of forces necessary for screwing, bolting, or guiding heavy components safely. Access and erection require the use of a mobile elevating work platform or the installation of heavy-duty scaffolding brackets providing a genuine continuous working platform in front of the façade.
Planning timber framing works thus requires checking the roof geometry as early as the workshop phase. Pre-drilling or preparing steel post fixing points or ordering an all-terrain articulating boom with sufficient outreach must be included in construction site preparation. This organisation prevents hoisting interruptions caused by the impossibility of erecting edge protection suitable for the actual pitch.
Managing protection failures and emergency measures at the roof edge
On a timber framing construction site, temporary protection configurations can be compromised during the installation of rafters, wall plates, or large prefabricated elements. The unexpected absence of perimeter edge protection, anchor pull-out due to wind, or geometric impossibility of working from a steeply pitched roof requires an immediate response from technical supervisors.
- Immediate perimeter securingPhysically prohibit access to the unprotected roof slope using red and white chain barriers at a safe distance or timber battens nailed across the rafters.
- Switching to powered access equipmentWhen the slope angle prevents footing on the roof or when edge protection is dismantled to pass a truss, bring in an articulating or telescopic mobile elevating work platform.
- Resuming assembly from the basketCarpenters carry out wall plate screw-fixing and steel bracket nailing from the basket, with harnesses attached to the manufacturer's dedicated anchor point.
- Inspection prior to workstation reoccupationVerify the mechanical strength of the fixing points on the reinstalled perimeter protection before re-authorising direct work on the timber structure.
The employer applies the measures required by art. 82 LAA to prevent occupational accidents by adapting technical devices to the structural realities. If an unusual edge configuration prevents the use of standard brackets, deploying a mobile platform ensures the safety of teams without improvising precarious anchors on unbraced timber.
Frequently asked questions
At what exact moment does edge protection become mandatory in timber framing?
Protection is required as soon as the possible fall height exceeds 2 m above the ground or the lower receiving level. On traditional timber framing or timber stud walls, this height is measured at the eaves or the lowest open edge. If this threshold is crossed, no purlin or rafter installation work can begin without perimeter edge protection or a suitable collective device.
How do you work on a slope with a pitch exceeding 60 degrees?
On slopes with an inclination greater than 60°, keeping a carpenter directly on the roof surface becomes impracticable and dangerous. According to art. 41 OTConst, work on these roofs is carried out solely from scaffolding or a mobile elevating work platform. The tradesperson works from the platform basket without ever bearing onto the rafters of the steep slope.
Can edge protection be replaced by an individual fall arrest system?
Collective protection systematically takes precedence over personal protection. Using a harness with a fall arrest lanyard on timber framing constitutes an exceptional substitution measure. It is only permitted for operations of very short duration or when erecting a collective perimeter device proves technically impossible. The foreman must justify this choice and ensure certified anchors are present on the timber frame.
Who verifies elevating platform stability on soft ground?
The site manager or foreman checks soil bearing capacity prior to any platform deployment around the building. On backfilled or waterlogged ground, rigid spreader plates made of hardwood or synthetic material must be placed beneath outriggers. In case of geotechnical doubt, the machine is positioned on a crushed-stone platform prepared by the earthworks contractor.
Texts and standards cited
- LAA art. 82general prevention rules: the employer shall take, to prevent occupational accidents and diseases, all measures shown to be necessary by experience, feasible according to the state of technology, and adapted to the prevailing conditions; workers shall assist them (in particular, they use personal protective equipment)
- OTConst art. 41measures to be taken at roof edges: appropriate measures to prevent falls from a fall height of more than 2 m (tinsmith scaffold and/or perimeter edge protection depending on roof pitch); on roofs with a pitch of more than 60°, work solely from scaffolding or a mobile elevating work platform (al. 3)
