Key takeaways
- A floor verified for static deflection can still cause marked vibration discomfort under foot traffic.
- Standard SIA 265 requires serviceability to be considered beyond structural failure alone.
- Increasing joist depth remains the most effective structural lever in the workshop.
- Screw-gluing floor panels and solid strutting prevents the transmission of tremors.
Why strength and deflection calculations are insufficient for dynamic comfort
On construction sites in French-speaking Switzerland for renovations or vertical extensions, sizing a joist floor traditionally begins by complying with ultimate limit states, which ensure no member fails under live loads. The carpenter then checks the serviceability limit state in the form of instantaneous deflection and final deflection including creep. However, a floor complying with these criteria can prove highly uncomfortable for occupants: under the simple impact of an adult footstep, glasses rattle in cabinets and shockwaves travel across the room. This phenomenon is not a bearing capacity issue, but a matter of natural frequency and oscillating mass.
Serviceability requirements must be met; permissible deformations and vibrations must be adapted to the intended use of the structure in order to prevent damage to non-structural elements and ensure the comfort of occupants.
norme SIA 265
The fundamental problem lies in the mass-to-stiffness ratio inherent to timber. Being very light compared to concrete, timber possesses low mass inertia. If the fundamental natural frequency of the structure drops close to human walking pacing, footsteps resonate with the joists. Standard deflection checks under distributed static load provide no insight into point flexibility under a concentrated footstep load, nor into the rate of shockwave dissipation.
| Structural criterion | Physical quantity verified | Defect perceived by the user |
|---|---|---|
| Ultimate limit state | Bending and shear stresses | Risk of sagging or joist failure |
| Static deflection (SIA 265) | Deflection under total load (mm) | Cracking of plaster or lightweight partitions |
| Vibration comfort | Natural frequency (Hz) and point deflection | Spring effect underfoot, rattling crockery |
Constructive measures: centres, rows of strutting, and composite subflooring
When overall floor thickness is restricted by clearance or ceiling-height constraints, carpenters have assembly and workmanship levers to stiffen the system. The first parameter is joist centres. While an interval of 600 mm or 625 mm remains economical for cutting raw panels without waste, reducing this spacing to 400 mm or 500 mm profoundly alters local stiffness. It also ensures better nailing or screwing along end edges and prevents differential deflection of the subfloor sheet between consecutive joists.
- Joist layout and setting outCheck seating levels on ledger boards or wall plates, adjust centres to the millimetre, prioritising reduced spacing to increase the number of rigid supports beneath distribution panels.
- Installation of full-depth rows of solid struttingInstall solid struts cut from the same section as the joists at mid-span (or at the third points for spans over four metres); fix home using ring-shank nails or screws to lock the members together.
- Continuous gluing of top chordsApply a continuous bead of structural polyurethane or hybrid adhesive along the top face of joists before positioning the floor panel.
- Close-pitch screwing of wood-based panelsMechanically fasten the panel with closely spaced screws along the top chords to create an effective T-section that mobilises the floor in compression.
The role of solid strutting is often underestimated: it does not merely prevent lateral-torsional buckling of slender members. Properly fitted and nailed, it forces five or six adjacent joists to deflect together under localised impact, rather than leaving the impacted joist to deform alone. Adding structural OSB or plywood screwed and glued to the top edge transforms the assembly into a composite timber-panel beam, which significantly raises overall stiffness.
Dynamic behaviour to standard SIA 265 and stiffness levers
A joist floor designed exclusively for the ultimate limit state (failure strength) and verified for standard static deflection criteria (generally w_net,fin between L/300 and L/500) can exhibit unacceptable residual flexibility in service. During paced walking, induced kinetic energy excites the system's flexural vibration modes. If the fundamental frequency drops too low, the sensation of bounciness and rattling furniture disturb the occupant, even though no structural damage appears in the timber.
Vibration requirements for timber floors must be verified at the serviceability limit state to avoid user discomfort, by limiting instantaneous deformation under concentrated point loads and checking the natural frequency of the structure.
norme SIA 265
Standard SIA 265 requires rigorous vibration comfort checks in residential and office buildings. The check is based on two inseparable criteria: a minimum floor natural frequency to prevent resonance with human footsteps (usually set above 8 Hz for a standard floor), and adequate point stiffness limiting localised deflection under a concentrated force simulating occupant weight (1 kN unit point load).
To achieve a frequency above 8 Hz on spans exceeding 4.50 m, simply upsizing the solid timber or glued laminated timber section incurs prohibitive material costs. Required inertia is gained more effectively by increasing joist depth rather than width, and especially by mobilising the upper engineered panel (OSB/3, plywood, or cross-laminated panels) to act compositely as a T-section.
| Construction configuration | Effect on overall inertia | Impact on natural frequency | Reduction of point deflection |
|---|---|---|---|
| Top panel screwed only | Low inertia gain (significant relative slip) | Negligible (+0.2 to +0.5 Hz) | Transverse distribution limited to adjacent joists |
| Panel glued and screwed to joists | Rigid composite action (25 to 40% increase in flexural inertia) | Significant increase (+1.5 to +3.0 Hz) | Substantial reduction in local deflection under 1 kN |
| Tightly fitted end and mid-span strutting | No effect on unit axial stiffness | Moderate gain through transverse coupling | Load distribution across 3 to 5 joists |
| Dry screed with mineral ballast | Unchanged inertia, addition of surface mass | Frequency drop offset by damping inertia | Rapid attenuation of perceived vibration velocity |
On-site installation: remediating comfort during execution
On the construction site, the carpenter has direct installation methods to ensure or restore vibration comfort without altering the primary sections cut in the workshop. Structural gluing of the upper distribution panel to the top face of the joists transforms isolated members into a monolithic grid. This connection must be made with an expanding polyurethane adhesive to bridge surface tolerances, combined with regular, closely pitched screwing (typically 150 mm at panel edges and 250 mm in the field) to maintain mechanical clamping during curing.
- Alignment and rigid packing of supportsCheck the level of bearing ledgers or wall plates. Any play or air gap under a metal joist hanger or housing joint generates acoustic shock and destroys calculated dynamic stiffness.
- Installation of strutting and centreline stiffenersInstall rows of solid strutting at mid-span. Select sections matching the joist depth and clamp tight before securing with inclined fully threaded screws or nailed metal brackets.
- Mechanical gluing of subfloor diaphragmClean joist top faces, apply a continuous adhesive bead without breaks, set down the panel, and screw down immediately to the required pitch before the adhesive skins over.
- Controlled ballasting and decouplingInstall mineral ballast granules or dry screed elements to provide damping mass inertia, without binding these masses to perimeter walls.
If the floor displays excessive springiness during on-site progress checks, soffit-side strengthening is the preferred remedial solution. Applying post-tensioned steel strapping, screwing hardwood inertia plates to the underside of joists, or connecting a continuous cross-braced tie-rod system stiffens the assembly without dismantling the upper floor build-up.
Finally, the site foreman ensures that load shedding and temporary site loadings comply with structural safety. Pursuant to art. 3 OPA, the employer shall take all measures and protective provisions complying with recognised technical rules to prevent accidents during handling and storage of heavy stiffening elements.
Floor too flexible after installation: diagnostics and remedial measures
When a timber joist floor passes bearing capacity checks and deflection limits under quasi-permanent loads but transmits unpleasant footfall vibrations, the carpenter faces a serviceability failure. If the vibration comfort assessment to standard SIA 265 was underestimated during the design phase, the actual dynamic behaviour reveals a lack of transverse bending stiffness or insufficient surface mass.
- Inspection of decking fixingsCheck the nailing or screwing line of wood-based panels. Missing glue in tongue-and-groove joints or excessive screw spacing eliminates the diaphragm action needed for load sharing between adjacent joists.
- Mechanical stiffening with solid struttingInsert full-depth solid timber or glulam struts and stiffeners. Clamping under preload using twin-thread screws restores lateral connection and raises the natural frequency of the span.
- Addition of mass and structural couplingIncorporate a bed of crushed gravel or reinforced plasterboard between joists before laying the dry screed. This dead mass damps footsteps without dangerously overloading supports.
Executing side flitching of existing joists with steel profiles or glued-laminated timber flitches improves the overall moment of inertia. These interventions prevent disruptive refurbishment if ceiling void height permits.
Frequently asked questions
Is static strength calculation sufficient to eliminate the risk of vibration?
No. Joists sized solely to carry permanent and live loads satisfy structural safety without guaranteeing comfort. The instantaneous deflection criterion does not limit felt acceleration or oscillation amplitude induced by human footfall. Dynamic requirements under standard SIA 265 require a specific verification of the fundamental natural frequency and minimum stiffness under concentrated point loads.
Why glue the subfloor to joists in addition to screwing?
Structural gluing of decking to the top chord of joists eliminates slip at the timber-to-timber interface. This bond forms a composite T-section that increases the span moment of inertia by up to 30 per cent. This direct gain in stiffness raises the floor natural frequency, reduces local deflection under point loads, and prevents the subsequent development of annoying squeaks under foot traffic.
How effective is solid strutting against vibration discomfort in practice?
Tightly fitted rows of solid strutting prevent lateral-torsional buckling of slender joists and distribute the impact of a footstep across multiple adjacent members. Instead of an isolated joist deflecting under the user, the assembly engages the active width of the floor. To be fully effective, these members must span almost the full depth of the joists and be securely fixed using skew screws or metal connectors to prevent any residual dynamic play.
How do you correct an upper floor that vibrates after laying parquet flooring?
Once the top floor finish is installed, access is gained from the ceiling soffit. The carpenter can insert diagonally screwed rows of strutting, fix tension plates screwed to the tension chords of the joists, or flitch each timber flank with glued and dowelled timber planks. Installing a suspended ceiling on acoustic hangers lined with mineral wool also improves overall damping.
Texts and standards cited
- norme SIA 265Timber structures - Design and structural verification, including dynamic behaviour and floor vibration comfort.
- CO art. 365Materials and ground: the contractor is liable for the sound quality of materials supplied; if materials supplied by the client or the ground designated by them are defective, or if any other circumstance compromises the regular or timely execution of the work, the contractor shall immediately inform the client, under penalty of bearing the consequences (para. 3).
