Key takeaways
- Standard SIA 265 conditions mechanical strength on rigorous visual grading of rough sawn timber.
- An isolated knot on a tension edge weakens strength far more than in a compression zone.
- Superficial drying splits are permissible, whereas through splits require rejection.
- Wane reduces the effective cross-section and compromises connections using metal connectors or brackets.
Classifying knots according to their mechanical position and member stress
Solid timber used in framing or traditional carpentry exhibits growth irregularities that must be assessed upon delivery on the construction site or during cutting in the workshop. Not all knots downgrade a load-bearing element: their impact depends directly on their relative diameter, grouping, and position relative to the stressed grain. SIA 265 governs these criteria by setting the permissible limits for each strength class, commonly C24 for indigenous softwoods such as spruce or silver fir.
- Knot in the tension zone
- Wood irregularity located in the lower third of a bending member or in a tension tie of a truss. It interrupts grain continuity and creates a local stress concentration highly unfavourable to axial tension.
Best building practice requires inspecting the edges of purlins, bressummers, and principal rafters first. A sound, intergrown knot located right at mid-depth of a bending member, at the neutral axis, still participates in transmitting shear stresses and barely reduces load-bearing capacity. Conversely, a knot of the same diameter emerging on the bottom edge subjected to pure tension immediately reduces strength by initiating brittle failure. During layout, the carpenter takes care to flip the member to orient large edge knots toward the upper compression zone, where the wood tolerates grain deviation significantly better.
| Type of anomaly | Compression zone (top edge) | Neutral axis (member centre) | Tension zone (bottom edge) |
|---|---|---|---|
| Sound intergrown knot | Permissible depending on section ratio | Low impact on bending | Critical if located on the edge |
| Unsound or decayed knot | Tolerated if isolated and small | Permissible subject to inspection | Ground for immediate rejection |
| Group of closely spaced knots | Check cumulative diameters | Pay attention to bearing areas | Rejection if centre-to-centre distance is short |
Managing drying splits, through splits, and section loss due to wane
The hygroscopic behaviour of timber generates differential shrinkage between the tangential and radial planes. These volumetric variations cause longitudinal splits to appear during the drying phase. Assessing these defects requires a clear distinction between superficial drying checks, inherent to rough timber, and through splits that divide the timber into two distinct volumes.
A straight drying split that does not pass through the member from one face to the other and does not follow excessive cross grain only marginally affects bending moment resistance. However, if the split is located at the member end in a bearing area or passes through the cross-section at a connector or dowel joint, longitudinal shear capacity drops drastically. If the split goes through the full thickness from side to side over a significant length, the timber must be rejected or cropped before any fabrication.
- Wane
- Portion of the original outer cylindrical surface of the log, with or without bark, remaining on one or more edges of a squared piece after sawing.
The presence of wane alters the nominal geometry defined on the execution drawings. Beyond the aesthetic aspect relevant to non-exposed timber, wane poses a direct mechanical issue: it reduces the effective cross-section of the structural component. If design calculations were based on a 120 by 240 millimetre beam, continuous wane removing several centimetres of edge alters the section modulus and the moment of inertia of the piece. Moreover, it prevents the flush contact required when installing metal joist hangers, external-flange brackets, or nail plates.
- Visual dimensional checkMeasure the remaining height and width of sound wood on the waney edge using a steel rule.
- Probing end splitsInsert a thin feeler gauge to verify whether the split is superficial or completely traverses the load-bearing element.
- Checking connection zonesEnsure that no connector, dowel, or birdsmouth joint cuts into an area exhibiting wane or a split.
- Grading decisionAccept the member for fabrication, relegate it to non-critical secondary use, or order its removal from the structural batch.
Visual grading criteria and tolerances according to standard SIA 265
On the construction site or in the carpentry workshop, the visual inspection of structural softwood timber immediately determines the fate of a piece. SIA 265 establishes calculation rules and requirements applicable to timber structures. The suitability of a rafter, purlin, or post depends on strict compliance with the grading specifications defined for its strength class. While timber is a natural material whose heterogeneity is accepted, each anatomical irregularity must remain within strict limits to ensure the structural safety of the work.
| Observed irregularity | Standard class tolerance (C24) | Critical threshold for immediate rejection |
|---|---|---|
| Diameter of isolated knots | Less than or equal to one third of the face width | Greater than half of the face or clustered knots |
| Knot in the tension zone | Permissible if diameter is less than one quarter of the depth | Any knot emerging on the tension edge or exceeding one quarter |
| Superficial drying splits | Permissible without length limitation if depth is controlled | Through splits dividing the member or initiated shear failure |
| Wane on edge | Tolerated up to one quarter of thickness or width | Presence at a support, connection, or exceeding one third |
Assessing irregularities is not done in isolation. A structural timber member can exhibit a slight wane and a few sound knots simultaneously. However, the accumulation on the same cross-section of several irregularities approaching the maximum permitted thresholds requires immediate downgrading to a non-load-bearing use, such as temporary bracing or workshop blocking.
Acceptance protocols, effective cross-section verification, and rejection
When unloading rough or planed timber, the site foreman or team leader applies a systematic inspection protocol before layout and machining. The inspection focuses primarily on preserving the full effective cross-section. Excessive wane reduces bearing contact area and compromises the positioning of metal fasteners such as dowels or fully threaded screws.
- Examination of the tension faceIdentify the intended orientation of the bending member. Verify the absolute absence of unsound knots, decayed knots, or edge knots in the middle third of the span in the zone subjected to tension.
- Measuring longitudinal splitsProbe split depth using a thickness gauge. Distinguish normal radial shrinkage from a through split capable of splitting the piece under shear stress at supports.
- Geometric check of waneMeasure the residual squared cross-section. Reject or recut any member where wane eliminates the anchoring timber required for connectors or reduces the minimum prescribed bearing on wall plates.
- Marking and sortingApply a red chalk mark to timbers rejected for load-bearing functions. Isolate elements that can be reused after cutting off defective sections.
In accordance with art. 365 CO, the contractor is responsible for the good quality of the material supplied. The carpenter who receives sawn timber exhibiting defects critical to structural safety must exercise their duty of inspection before incorporating it into the framework.
The cost of preventive replacement of a rough member is negligible, around 40 to 90 CHF per standard piece, compared to damage caused by timber failure under load once the structure is in service.
Non-conformity management and dispute resolution on the construction site
On a timber construction site, discovering a geometric or structural defect during unloading or cutting calls for a strict protocol. If a piece of solid timber or glued laminated timber presents a non-compliant knot in the tension zone, a through split, or wane exceeding the tolerance of the specified class, it must under no circumstances be incorporated into the work without engineering approval.
- Isolation and marking of the elementThe defective timber is immediately marked with timber chalk, measured for residual effective cross-section, and removed from the assembly area to prevent inadvertent installation.
- Joint inspection record and documentationThe team leader records the dimensions of the defect (knot diameter, split depth and length, wane dimension) and forwards a date-stamped photographic report to the site management and the sawmiller.
- Notice of defect and consulting the engineerThe contractor formally notifies the defect under the Code of Obligations (CO). The timber engineer verifies whether a recalculation of stresses according to SIA 265 allows the piece to be accepted, possibly by modifying its mechanical orientation.
- Removal or reassignmentWithout written approval from the site management or the civil engineer, rejected timber is removed from the site or downgraded to secondary non-load-bearing use (blocking, perimeter noggings).
Art. 365 CO specifies that if the material supplied by the client or the ground designated by them is found to be defective, the contractor must inform the client immediately. Art. 229 CP punishes anyone who intentionally or through negligence breaches the recognised rules of construction when carrying out building work and thereby endangers the life of others. Written traceability protects the enterprise against subsequent claims.
Frequently asked questions
Can a purlin with a large sound knot on its bottom face be installed?
No, a knot located on the underside of a bending member is directly in the tension zone. Even if sound and intergrown, it deviates the timber grain and severely reduces the tensile strength of the chord. Under the rules of standard SIA 265, this defect precludes the piece from this function, unless flipping it places the knot in the compression zone, subject to verification of the permissible deflection.
How do you distinguish an acceptable drying split from a critical defect?
A superficial drying split is natural and tolerated if its depth does not cross the neutral axis of the cross-section. Conversely, a through split dividing the piece from side to side cancels longitudinal shear strength. On a member subjected to bending, this mechanical failure warrants immediate rejection of the piece or a complete recalculation by the design office before any installation.
What should be done if significant wane reduces the edge of a load-bearing rafter?
Wane decreases the bearing area and the effective cross-section required to carry loads. If the geometric reduction exceeds the threshold set for the required structural class, the piece cannot be installed as is. The contractor must measure the remaining bearing width at supports and consult the timber engineer to validate the transverse compressive stress or replace the timber.
Can a remedial treatment repair a split that appeared after installation?
No preservative or impregnating product restores the mechanical continuity of broken fibres. Applying a product in the workshop or on the construction site serves only a fungicidal or insecticidal role. When faced with an expanding split outside the tolerances of standard SIA 265, remediation requires structural timber solutions: flitching, installing transverse threaded rods with joint design calculations, or outright replacement of the member.
Texts and standards cited
- SIA 265Design rules, strength classes, and mechanical requirements for timber structures.
- CO art. 365Contractor liability regarding supplied material and the duty to immediately inform the client if material is found to be defective.
- CP art. 229Penalties for breaching the recognised rules of building work that endanger the life or physical integrity of individuals.
