Skip to content
Website
🧱 CFC 214Timber connections, ironmongery and fastenersChapter 1 of 10 in the section

Structural screws: pre-drilling, spacing, and edge distances

After this chapter, you will know how to set out and install structural screws without splitting timber members or destroying their mechanical anchorage. You will master the rules on edge distances, spacing, and pre-drilling requirements defined by standard SIA 265, applicable to native softwoods, hardwoods, and engineered wood panels.

Key takeaways

  • Pre-drilling remains mandatory for all dense hardwoods to prevent structural splitting.
  • Edge and end distances directly depend on the grain orientation of the timber.
  • Overtightening strips the thread in the fibres and destroys the pull-out resistance.
  • Standard SIA 265 specifies the minimum geometric coefficients to be applied based on the nominal diameter.

Setting out screws according to edge, end, and centre-to-centre distances

On a timber construction site, partially or fully threaded screws commonly replace traditional bolts and ring-shank nails. Their geometry provides very high axial and shear load-bearing capacity, on the express condition that the timber material around the thread is not delaminated during driving. The most common mistake consists in positioning the fastener too close to the end of a purlin or rafter for easier access, which causes the timber to burst under the wedging effect generated by the metal core.

Connections using dowel-type fasteners must respect minimum spacing and edge distances sufficient to prevent premature failure by splitting of the timber along the grain or by block shear.

norme SIA 265
Indicative minimum distances for wood screws without pre-drilling based on the nominal diameter d
Fastener positionAngle to the timber grainMinimum distance without pre-drillingMinimum distance with pre-drilling
Loaded edgePerpendicular load7 d5 d
Unloaded edgeParallel load5 d3 d
Loaded endLoad towards the end15 d10 d
Unloaded endLoad away from the end10 d5 d
Spacing within a rowParallel to the grain10 d5 d
Spacing between rowsPerpendicular to the grain5 d3 d

Failure to comply with these geometric requirements directly engages the liability of the contractor. In the event of structural damage resulting from insufficient spacing that degrades the load-bearing capacity of a primary element, the Swiss Criminal Code becomes applicable. According to art. 229 CP, anyone who, in directing or executing a construction or demolition, intentionally breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons is liable to a custodial sentence not exceeding five years or a monetary penalty. Rigorous setting out on rough timber remains the primary safeguard against this risk.

Mastering pre-drilling by species and adjusting the tightening torque

The widespread use of self-drilling screws equipped with cutting or milling points has spread the illusion that pre-drilling has become redundant on glulam or timber-frame construction sites. While this exemption works in softwoods such as spruce or silver fir, provided safety distances are respected, it becomes prohibited as soon as dense species or heavily loaded joints are tackled.

  1. Checking species and moisture contentIdentify the load-bearing material. On softwoods (density below 500 kg/m³), anti-splitting points are permitted without a pilot hole. On native hardwoods (oak, ash, beech) or hardwood glulam members, pilot drilling is strictly mandatory over the full penetration length to prevent shank failure through torsion.
  2. Selecting the drill bit diameterFor the threaded part, the drill bit must match the diameter of the screw's metal core (often between 60% and 75% of the nominal outer diameter). For the smooth shank of a partially threaded screw, pre-drilling must reach the full nominal diameter to ensure the two members are drawn tightly together without play.
  3. Torque adjustment on the screwdriverDeactivate hammer mode on machines. Use a screwdriver with a torque-limiting clutch or visually monitor driving without persisting once the countersunk head is flush with the surface. Continuing rotation when the head has already seated mills the timber under the head and destroys the female internal thread formed by the screw in the receiving timber.

In the specific case of cross-laminated timber (CLT) panels, driving into narrow edges systematically requires compliance with manufacturer specifications and standard SIA 265 principles. In the edge of a panel, pre-drilling remains strongly recommended even for spruce when the diameter exceeds 6 mm, as delamination of the cross-layers under penetration load halves the shear strength. Finally, regarding contractual liability, art. 365 CO reiterates that the contractor is liable for the sound quality of the materials they supply; this includes hardware, certified fasteners, and the full preservation of the material entrusted to them.

Mechanical behaviour and edge failures according to standard SIA 265

The transmission of loads by partially or fully threaded screws stresses timber anisotropically. When a structural screw is driven without respecting the specified spacing, the splitting stress perpendicular to the grain exceeds the cross-tensile strength of the load-bearing element. According to standard SIA 265, the risk of brittle failure by splitting takes precedence over the ductile failure mode of the steel when longitudinal or transverse edge distances are insufficient.

The end of a softwood member (spruce, fir, larch) constitutes the most vulnerable zone to tearing along annual growth rings. A force directed parallel to the grain towards the end stresses the end margin directly. Without a pilot hole, the self-drilling tip forces the fibres apart and induces permanent radial pressure. If external load is added to this initial state of tension, failure occurs abruptly along the shear plane with no visible plastic warning.

Regulatory minimum distances and applicable reductions based on structural detailing
Connection configurationDistance to loaded endDistance to unloaded endDistance to edge
Standard softwood without pre-drilling (diameter d)12 to 15 d7 to 10 d4 to 5 d
Softwood with calibrated pilot hole (diameter d)8 to 10 d5 d3 to 4 d
Hardwoods (oak, beech, ash) with pre-drilling12 d6 d4 d
CLT / cross-laminated panels (perpendicular narrow edge)10 d5 d3 d

Pathologies of overtightening and good workshop and construction site practices

The second common failure mode on timber construction sites involves local destruction of the material during the final phase of driving. The use of non-clutched impact drivers frequently leads to spinning the screw in the anchorage zone. As soon as the thread destroys the timber cylinder into which it should bite, axial pull-out resistance drops irreversibly, rendering the connection ineffective against wind uplift loads or diagonal tensile forces from braces.

  1. Visual inspection of species and grain orientationCheck the grain direction of the load-bearing timber and identify any existing seasoning checks on the ends of purlins or girders before any setting-out marking.
  2. Systematic marking of centre-to-centre spacingMark out the positioning grid with a carpenter's pencil, incorporating safety edge distances according to standard SIA 265, without relying on approximate visual alignment from the edge of the piece.
  3. Execution of the pilot hole in dense timberFor native hardwoods or high-density glulam, drill along the full length of the smooth shank to a diameter equal to the screw shank, and over the threaded zone to the core diameter.
  4. Setting the depth stop or torqueAdjust the torque setting on the machine to stop rotation as soon as the countersunk or washer head sits flush with the timber element or metal fitting, without crushing the upper fibres.

In terms of inspection management, the foreman checks effective tightening by spot checks, applying a manual verification torque with a torque wrench or ratchet on 5% of critical fixings. If a shank is found to spin freely, the stripped screw must be removed immediately, the area structurally plugged with a pressure-glued dowel, or the connection supplemented with a larger diameter screw offset in accordance with regulatory distances.

Connections must be designed and executed in such a way that foreseeable deformations and dimensional changes due to timber moisture content do not cause unacceptable secondary stresses or premature failure by splitting.

norme SIA 265

Management of anchorage non-conformities and remediation procedures

On a timber construction site, the appearance of a longitudinal crack during structural screw installation or free spinning resulting from excessive tightening torque immediately invalidates the static design value of the connector. Faced with this situation, the carpenter cannot simply rely on cosmetic concealment or empirical tolerance. According to standard SIA 265, a member split along the fixing line has its shear and transverse tensile strength compromised, increasing the risk of brittle failure through splitting of the load-bearing timber.

  1. Identification and immediate neutralisationMark the non-compliant screw with timber chalk. If the screw spins freely, extract it or leave it unloaded without counting it towards the design verification of the fastener group.
  2. Inspection of timber member integrityCheck whether the timber grain shows the start of a crack towards the edge or end. If the crack reaches the end, the piece must be mechanically reinforced using transverse, fully threaded self-drilling screws or replaced.
  3. Drilling a replacement fastenerInstall a new screw, strictly observing the minimum spacing and edge distances specified by the timber engineer. If space is insufficient on the member, step up to the next nominal diameter after pre-drilling a suitable pilot hole.
  4. Communication and traceabilityAccording to art. 365 CO, if any circumstance arises that compromises the proper or timely execution of the work, the contractor must inform the client. Report connection adjustments to the site management and record the modification in the site logbook.

The foreman must ensure that screwdriver clutches are systematically set to prevent recurrence of these defects. In the presence of dense hardwoods such as oak or ash, direct driving without full-length pilot drilling must be stopped completely to prevent any risk of shank failure through torsion.

Frequently asked questions

A structural screw spun freely at the end of driving. Can the new screw be placed right next to it?

No. Inserting a fastener immediately next to a stripped hole locally weakens the timber fibres and reduces load capacity. You must respect the minimum spacing specified by standard SIA 265 between the two centres, generally about five diameters. If there is insufficient room on the steel fitting, install a screw of a larger diameter or seek advice from the timber engineer to validate an offset installation.

Is pre-drilling mandatory for installing self-drilling structural screws in dry fir?

In standard softwoods like spruce or silver fir, structural screws equipped with a cutting tip generally dispense with pre-drilling within the span. However, pre-drilling the shank remains strictly required when approaching edges or ends to prevent the timber from splitting, as well as for large diameters from eight millimetres upwards installed without specific approved details under standard SIA 265.

What should be done when a fine crack appears at the edge of a beam during fastener tightening?

Any crack that reaches an edge compromises shear strength and tension perpendicular to the grain. This screw can no longer be considered load-bearing. The affected fixing must be neutralised, the crack propagation arrested by installing a transverse, fully threaded screw to clamp the split closed, and the replacement structural anchor installed further away, strictly observing the required centre-to-centre distances.

How should edge distances be adjusted when connecting cross-laminated timber (CLT) elements?

In cross-laminated timber, alternating cross-layers limits the propagation of longitudinal cracks compared to solid timber. However, driving screws into narrow edges requires increased care: the risk of delamination or driving into a glue line necessitates larger edge distances. The technical recommendations of the element manufacturers and design values compliant with standard SIA 265 must be applied.

Texts and standards cited

  • SIA 265Timber structures - Verification of structural safety and serviceability
  • CO art. art. 365 COmaterials and site: the contractor is liable for the sound quality of the materials they supply; if the materials supplied by the client or the building site designated by the client are found to be defective, or if any other circumstance arises that compromises the proper or timely execution of the work, the contractor must inform the client immediately, under penalty of bearing the consequences thereof (para. 3).

In the same section