Skip to content
Website
🧱 CFC 214Timber as a load-bearing material: species, grades and moistureChapter 6 of 10 in the section

Service Class: Adapting Timber to the Ambient Moisture of the Structure

After this chapter, you will be able to determine with precision the service class applicable to each timber component according to standard SIA 265. You will identify the equilibrium moisture content specific to heated spaces, ventilated roof spaces and sheltered structures, whilst avoiding procurement and installation errors that lead to structural defects.

Key takeaways

  • The service class defines the equilibrium moisture content of timber according to the actual ambient conditions of the structure.
  • Standard SIA 265 specifies the structural design and allowable dimensional variations for timber.
  • A heated indoor environment requires dry timber to prevent excessive shrinkage and detrimental splitting.
  • Adapting the material to its environment prevents connection shear failure and member distortion.

The Three Service Classes According to Standard SIA 265 and Their Application Environments

In Swiss timber construction, the mechanical and dimensional behaviour of load-bearing elements depends directly on their moisture content. Standard SIA 265 structures structural design by defining three service classes. This division is not merely a workshop classification: it directly dictates modification factors for mechanical strengths, moduli of elasticity for deflection calculations, and the management of long-term deformations through creep. Each class corresponds to specific thermo-hygrometric conditions, representative of the structure in its operational phase.

Classification of Environments and Moisture Contents According to Standard SIA 265
Service classAverage climatic conditionsEquilibrium moisture content of timberTypical timber structures
Service class 120 °C and relative humidity of the air exceeding 65% for only a few weeks per year5% to 12%Heated indoor environment, floor joisting, roofs insulated on the warm side
Service class 220 °C and relative humidity of the air exceeding 85% for only a few weeks per year12% to 20%Ventilated roof underlay, trussed rafters in cold roof spaces, enclosed canopies
Service class 3Climatic conditions leading to moisture contents higher than service class 2Greater than 20%Open external structures, sheltered footbridges without walls, posts under exposed canopies

The CFC 214 carpenter must imperatively distinguish these environments from the order preparation phase. The timber frame of a fully climate-controlled office building does not experience the same seasonal cycles as sheltered raftering under a cold roof. Disregarding this reality leads to selecting timber whose moisture content during installation differs radically from the building's final equilibrium point.

Adapting Timber Moisture at Installation to Neutralise Deformations

The most frequent and destructive technical error consists in erecting structural timber with a moisture content exceeding 18% within a space intended to become a heated indoor environment. Once the building is enclosed, insulated and heated continuously, the indoor air dries out quickly to reach a relative humidity between 30% and 50%. Under these conditions, the physics of the material dictates a realignment: the timber will inexorably drop towards its equilibrium moisture content, situated around 8% to 10%.

Equilibrium Moisture Content
Mass moisture content reached by a piece of timber stabilised in an environment defined by constant temperature and relative air humidity.

This massive loss of water below the fibre saturation point generates abrupt cross-sectional shrinkage. The consequences for the load-bearing structure are immediate: opening of longitudinal splits in solid timber sections, warping of members, excessive play in birdsmouths and step joints, and loss of tightness on metal dowels or timber bolts. For glued-laminated or cross-laminated timber, an excessively sharp moisture differential creates internal shear stresses capable of compromising the bonding performance of the glue lines.

  1. Inspection Upon Delivery to the Construction SiteCheck the core moisture content using an insulated-pin resistance moisture meter on at least 5 representative pieces per batch.
  2. Storage on Bearers and Under a Breathable SheetIsolate the timber packs from the bare ground by at least 15 cm and maintain perimeter ventilation without condensation beneath protective sheeting.
  3. Verification of Structural ConditionsRefuse the installation of finished class 1 elements as long as the concrete structural work emits saturating residual moisture without dehumidification.
  4. Systematic Retightening of Rods and FastenersSchedule a tightness check of bolted connections prior to the final closing of service linings.

The site foreman thus ensures that the delivery moisture content stated on cutting lists corresponds strictly to the intended use: roughly 9% to 12% for the frame and exposed purlins in heated spaces, compared to 15% to 18% for rafters and roof trusses installed in uninsulated ventilated spaces. This rigour guarantees the dimensional stability of the structure and preserves the structural integrity of the assembled connections.

Behaviour of Timber Under Climatic Variations by Service Class

Each service class defined by standard SIA 265 imposes a precise hygroscopic equilibrium that the carpenter must anticipate to ensure the dimensional stability of the structure. Adapting the material to the environment does not simply mean ordering kiln-dried timber, but ensuring its moisture content at the time of machining and assembly matches the future thermo-hygrometric conditions of the operating premises.

Thermo-Hygrometric Behaviour and Equilibrium Moisture Content According to Standard SIA 265
Operating environmentService classRelative air humidityEquilibrium moisture content of timberPredictable dimensional behaviour
Heated indoor environment (dwellings, offices)Class 1Below 65% (20 °C)8% to 12%Post-commissioning shrinkage during the heating period
Ventilated roof underlay or open shedClass 2Between 65% and 85% (20 °C)12% to 18%Cyclical seasonal variations without condensation
Sheltered exterior or exposed to the weatherClass 3Above 85%Over 18%Initial swelling and maximum dimensional ranges

In a heated indoor environment, air dried by heating systems lowers the ambient relative humidity to around 35% to 45% in the middle of winter. Structural elements enclosed within the insulated building envelope then reach an equilibrium moisture content of around 9%. If a glulam beam or framing member was machined and erected at 16%, the drying differential triggers significant tangential shrinkage, leading to splits along the grain and secondary stresses on metal fasteners.

Installation Error: Site Management and Shrinkage Pathologies

The primary error in timber construction lies in installing solid or engineered timber elements whose moisture content does not match the final service class, combined with a lack of protection against water ingress on the construction site. When a cross-laminated timber slab or multi-lam solid timber purlins are installed prematurely before liquid screeds are poured or without temporary weatherproofing, the material absorbs free water.

Rapid desorption following the enclosure of the building and sudden heating creates transverse tensile stresses perpendicular to the grain. In thick solid sections, the moisture gradient between the dried perimeter and the still-moist core generates deep shrinkage cracks. These fissures reduce the effective shear area and compromise load-bearing capacity at notch supports or fastener dowels.

  1. Inspection of Timber Upon Delivery to SiteMeasure moisture using a meter with insulated pins driven into the core, recording the values per batch to verify compliance with the design service class.
  2. Weather Protection During AssemblySystematically sheet wall heads and metal connections at the end of each day to prevent standing water from penetrating the end grain through capillary action.
  3. Progressive Thermal CommissioningDemand a phased temperature rise of the structure during initial heating to avoid hygrometric shock and limit surface evaporation rates.

Moisture Disputes and Non-Conformities: Technical and Contractual Management

On a construction site in French-speaking Switzerland, any discrepancy between the timber moisture measured upon delivery and the requirements of the service class specified by the timber engineer creates immediate friction. If load-bearing glulam or stud-wall elements exhibit a moisture content incompatible with the future equilibrium moisture content of the heated room, the foreman must reject the installation. Installing excessively wet timber in a space intended to be sealed and heated inevitably leads to shrinkage cracks, loosening of dowels, and damage to finishing work.

  1. Joint Moisture AssessmentMeasure the moisture content by mass using an insulated-pin moisture meter driven into the core, recording the temperature of the timber piece and the ambient humidity on the inspection sheet.
  2. Stabilisation or Covered DryingStore timber on bearers with at least 15 cm of ground clearance under a breathable tarpaulin in service class 2 conditions, or mechanically ventilate indoor volumes without sudden heating.
  3. Connection Inspection and RetighteningCheck the preload on threaded rods and metal connectors after the first heating period to compensate for radial and tangential shrinkage of the members.

Frequently asked questions

How should one react if interior glulam shows 16% moisture upon unloading?

For a heated indoor environment in service class 1, this value is excessive. The equilibrium moisture content will settle below 12%. You must record the measurement on the delivery note and notify site management of the situation. Heating these elements without prior drying will trigger major shrinkage splits and warping of members under load.

Can a ventilated roof structure be installed with timber at 18% moisture?

Service class 2 permits a higher moisture content during assembly, as sheltered outdoor air maintains an equilibrium close to 15%. A value of 18% remains acceptable if under-roof ventilation is provided immediately and no airtight board confines the timber. Progressive drying will prevent any surface fungal growth before the building elements are fully closed.

Who is liable for shrinkage cracks appearing after the heating is switched on?

If the carpenter installed timber compliant with the order specifications of standard SIA 265, defects resulting from an excessive or uncontrolled temperature rise in the building are an operational issue. Conversely, if moist solid timber components were incorporated into a heated volume without written notice, the carpenter is liable for failing to adapt the material to the service conditions.

How can the moisture of a large-section beam be validly measured on the construction site?

Use an electrical resistance moisture meter equipped with Teflon-insulated pins. Drive the electrodes perpendicular to the grain of the timber up to one third of the member's thickness to measure the core moisture content. A surface measurement produces a reading skewed by immediate climatic conditions. Systematically record three measurement points distributed along the length of the load-bearing member.

Texts and standards cited

  • SIA 265Timber Structures - Actions and Design of Load-Bearing Structures
  • CO art. 365Materials and site: the contractor is liable for the sound quality of the materials they supply; if the material supplied by the client or the site designated by them is found to be defective, or if any other circumstance compromises the regular or punctual execution of the work, they shall immediately inform the client thereof, under penalty of bearing the consequences (para. 3).

In the same section