Key takeaways
- Setting regular centres ensures installation of wood-based panels without cuts.
- Standard SIA 265 governs buckling design and transverse pressure on plates.
- Any point load path requires paired studs aligned down to the lower supports.
- Top and bottom plates ensure load transfer and perimeter tying of the structure.
Set the framing grid and determine standard sections
The choice of centres determines the entire construction chain of timber framing. On Swiss construction sites, the 625 mm grid is the modular benchmark for optimising the use of wood fibre or wood-based racking panels and standardised insulation batts, thus limiting cut-off waste. However, 417 mm centres remain specified when wind loads or floor loads require an increased stud density, or where specific internal linings demand a closer pitch.
| Insulation thickness | Standard sawn section | Recommended centres | Field of application |
|---|---|---|---|
| 160 mm | 60 x 160 mm | 625 mm | Internal load-bearing walls or external walls with added external insulation |
| 200 mm | 60 x 200 mm | 625 mm | Standard external walls for detached houses or small multi-unit buildings (ground + 1) |
| 240 mm | 60 x 240 mm | 625 mm or 417 mm | External walls with high thermal performance or heavy roof loads |
| 240 mm and above | 80 x 240 mm | 417 mm | Studs under severe axial loads and large clear heights |
The minimum section width of 60 mm provides the bearing area required for nailing or stapling structural panels with flush joints, while ensuring the edge distances required by standard SIA 265. Below this, the risk of timber splitting during mechanical fixing under pneumatic pressure increases drastically. The wall thickness, generally between 160 and 240 mm, satisfies both the mechanical inertia requirements against buckling and the thermal performance criteria of the envelope.
- Stud buckling
- Elastic instability of a stud subjected to an axial compressive force. In the plane of the wall, the bracing panel prevents lateral displacement; out of the plane of the wall, resistance depends exclusively on the width of the stud and its clear storey height.
Ensure continuity at plates and accommodate concentrated loads
The transmission of vertical loads from upper levels down to the foundations requires strict axial continuity. The top plate receives floor joists or roof trusses, while the bottom plate distributes these forces onto the slab or raft via a treated sole plate. Design must imperatively include verification of compression perpendicular to the grain according to standard SIA 265. Crushing of the plate's perpendicular fibres is frequently the limiting factor even before the vertical studs buckle.
- Locating the load pathIdentify on the structural timber drawings the exact location of primary purlins, steel girders or glulam primary beams transferring a distinct point load onto the top plate.
- Fabrication of the reinforcing postAssemble two to four studs of the same section as the standard grid using staggered nailing or screwing, so as to form a monolithic post directly beneath the point of impact.
- Fit under the plateDress the end cuts perfectly square to ensure full wood-to-wood contact with both the top plate and bottom plate, eliminating any fitting gap likely to cause structural settlement.
- Continuation through lower storeysDuplicate the reinforcement stack identically through walls on lower storeys down to the solid reinforced concrete foundation, inserting rigid transfer blocks through the floor depth.
The execution of works must comply with recognised trade practice regarding the strength of timber structures. On the construction site, site foremen ensure that connections between paired studs prevent any relative slippage. For all erection work on structural timber components and lifting of prefabricated panels, the employer takes the required technical measures in accordance with art. 3 OPA to prevent workplace accidents and provide erectors with stable workstations.
Transmission of forces to plates and management of compression perpendicular to the grain
The transmission of vertical forces between studs and bottom or top plates constitutes the critical point of design according to standard SIA 265. While the wall stud acts mainly in axial compression parallel to the grain, the bottom plate and top plate take the loads perpendicular to their grain. This loading in transverse crushing has significantly lower mechanical resistance, which frequently makes it the limiting criterion for overall stability beneath storeys or roof levels.
To prevent localised indentation of studs into the bottom plate, the carpenter must verify the effective bearing area. On the lower storey of a multi-storey building, a standard section of 60 x 160 mm may prove insufficient not due to buckling, but through crushing of the sole plate. Resorting to a higher timber grade (for example glulam instead of C24 solid structural timber) or widening the bearing plate provides the appropriate technical solution to meet the requirements of standard SIA 265 without disrupting the insulation grid.
| Framing element | Loading direction | Predominant failure mode | Workshop or site measure |
|---|---|---|---|
| Standard stud | Axial compression (parallel to grain) | Out-of-plane or in-plane buckling | Lateral restraint provided by the structural sheathing |
| Bottom plate / sole plate | Transverse compression (perpendicular to grain) | Crushing of the plate timber fibres | Section enlargement or dense timber |
| Top head binder plate | Local bending and transverse compression | Indentation under girder or offset joist | Doubled plate or strict alignment |
| Cripple stud under lintel | Localised axial compression | Crushing beneath end bearing | Structural bolting or nailing to the king stud |
Handling point loads and continuity of the load path
When floor framing or roof structures concentrate their support reactions—at the end of a primary purlin, a floor girder or beside a trimmer beam—standard regular centres are no longer sufficient. A point load path requires inserting a cluster of paired studs or an integrated post within the wall thickness, without breaking thermal continuity or hindering subsequent installation of the interior lining.
- Locating load paths on production drawingsIdentify precisely the position of major support reactions transmitted by the roof or upper floors, in order to plan reinforcements from the workshop prefabrication stage.
- Pairing and mechanical fastening of studsFasten two or three studs together using structural nails or screws in a regular pattern, ensuring monolithic behaviour against buckling under heavy loads.
- Setting out and vertical alignment from floor to floorPosition the reinforcing post directly plumb with the one on the floor below to transfer the load down to the raft or basement without loading joists in cantilever.
- Installation of steel distribution platesIf necessary, insert a steel plate between the head of the stud and the top plate to spread the concentrated load and avoid local crushing of the timber according to standard SIA 265.
From a contractual standpoint and regarding site execution safety, the carpenter ensures that temporary erection loads, such as stacking component packs on an unpropped floor, do not cause any structural defects. The contractor applies general accident prevention regulations to ensure the permanent stability of both temporary and permanent works throughout the lifting phase.
Centre non-conformities and crushing: remedial measures on site
On a timber frame construction site, discovering a misalignment between the stud grid and the floor load path demands immediate action before loading the upper floors. When the centreline of a primary joist or main girder does not fall directly plumb over a standard stud, the top plate undergoes local bending and compression perpendicular to the grain not anticipated by standard SIA 265.
The site foreman exercises the duty to notify provided for by the Code of Obligations (CO) prior to any structural modification. In accordance with art. 365 CO, the contractor notifies the client if any circumstance compromises the proper or timely execution of the work. The timber engineer then issues a technical remediation detail to restore a direct load path to the bottom plate.
- Installation of paired reinforcing studsInsert beneath the top plate, directly plumb under the concentrated load, one or two supplementary studs cut to the millimetre. These components are secured to the nearest stud with through-screws every 300 mm to prevent any lateral buckling under axial load.
- Verification of compression on the bottom plateCheck the crushing stress perpendicular to the grain on the bottom plate according to the criteria of standard SIA 265. If exceeded, insert a steel spreader plate or replace the plate locally with a dense hardwood or glulam piece.
- Correction of structural sheathing fixingsWhen actual stud spacing drifts from the pitch of the bracing panels, never leave an edge joint unsupported. Nail an intermediate framing stud to maintain nail edge distances and preserve the calculated panel stiffness.
Frequently asked questions
How should a point load falling between two studs be supported?
The top plate must never be allowed to act in simple bending. The carpenter inserts a reinforcing stud of a section matching the standard grid directly beneath the bearing point. This element runs continuous down to the bottom plate. It is fixed with coach screws or partially threaded screws to the adjacent stud to eliminate any risk of torsional-flexural or axial buckling according to standard SIA 265.
What centres should be chosen to reconcile insulation and wood-based panels?
The standard grid in French-speaking Switzerland is fixed at 625 mm centre to centre, which corresponds exactly to standard 1250 mm wide OSB or gypsum-fibre panel sizes. This dimension limits cut-off waste and ensures a snug fit for standard insulation batts. Reducing the grid to 417 mm is only required under severe vertical loads or specific seismic requirements.
What minimum section should be selected for studs supporting two levels?
As a rule, C24 solid timber studs have a minimum section of 60 × 160 mm, commonly increased to 60 × 200 mm or even 60 × 240 mm to accommodate the required insulation thickness. The final sizing remains determined by the engineer's calculation sheet according to standard SIA 265, incorporating unbraced buckling height and accumulated floor load paths.
How can crushing of plate fibres beneath studs be avoided?
Compression stress perpendicular to the grain on plates is often the governing factor. If the limit values of standard SIA 265 are exceeded beneath a loaded stud, the load-bearing stud is doubled or tripled to enlarge the contact surface. The engineer may also specify inserting a hardwood bearing pad or installing a steel spreader plate to distribute the force uniformly into the concrete.
Texts and standards cited
- SIA 265Timber construction: sizing of structural components, permissible stresses and limit state verification
- CO art. 365contractor liability for provided materials and duty to notify in case of circumstances compromising the works
