Skip to content
Website
🧱 CFC 214Traditional timber framing: trusses, purlins and raftersChapter 2 of 10 in the section

Wall plate: bearing on masonry, anchorage and moisture protection

This chapter details the installation rules for a wall plate on a masonry levelling course or a reinforced concrete ring beam. You will learn how to insert an effective DPC, how to size and install mechanical or chemical anchors against uplift, how to protect purlin ends from trapped moisture, and how to provide inspection access.

Key takeaways

  • The continuous DPC under the wall plate blocks rising damp coming from the concrete.
  • Anchoring to the ring beam resists horizontal shear forces and wind uplift.
  • The purlin end must never touch masonry nor be sealed with mortar.
  • Visual access for subsequent inspection ensures the durability of the roof's structural bearing.

Moisture barrier on levelling courses and mechanical anchorage to the ring beam

Placed directly on an untreated concrete levelling course or on clay bricks, the wall plate draws water up through capillary action. Fresh concrete or concrete exposed to the weather retains a high water content that migrates immediately into the structural timber fibres if no membrane separates the materials. This permanent moisture triggers biological decay in the bearing timber, which is very often invisible from the ground, compromising the overall anchorage of the roof.

Damp-proof course (DPC)
Flexible bituminous waterproofing strip or rot-proof synthetic membrane, inserted continuously between the top of the masonry and the underside of the timber wall plate to prevent moisture transfer.

The DPC must project on both sides of the timber member by at least 15 mm in order to prevent any lateral contact with render or residual water drops. Level packing of the wall plate must never be done using softwood packers or temporary shims left behind in fresh mortar: rot-proof synthetic packers with high compressive strength or phenolic marine plywood packers are used.

Anchorage methods for the wall plate in the reinforced concrete ring beam
Anchorage systemSuitable substrateAdvantages on the construction sitePoints to watch
Expansion anchor boltNon-cracked reinforced concreteFast installation through pre-drilled timberStrict compliance with edge distances from the levelling course
Resin-anchored threaded rodReinforced concrete, solid masonryExcellent resistance to pull-out loadsMeticulous dust removal from the hole with a blower
Bent flat steel tie strapIn-situ cast concreteNo drilling required at the top of the wallExact setting-out required before pouring
Concrete screw for timber framingReinforced concrete levelling courseDemountable and free of expansion stressesPre-drilling diameter calibrated to the millimetre

Under art. 365 al. 3 CO, if the material supplied by the client or the site designated by him is found to be defective, or if any other circumstance arises which compromises the proper or timely execution of the work, the contractor must inform the client immediately, under penalty of bearing the consequences. If the concrete levelling course has significant depressions, flatness defects outside tolerances, or exposed reinforcement, the carpenter records these defects before any installation of the wall plate.

Protection of ends, ventilation and inspection pockets

The end of a wall plate embedded in a gable wall or a masonry padstone is the primary location for fungal decay caused by confinement. When penetrating a wall or entering a wall head, the end grain absorbs water ten to fifteen times faster than the longitudinal faces. Sealing the end of a wall plate with cement mortar accelerates its decay by trapping moisture with no means of escape.

  1. Provide a perimeter air gapLeave a clearance of at least 20 mm at the end of the purlin and 15 mm on the sides against the masonry to ensure air circulation around the member.
  2. Protect the end grain before placementApply a fungicidal and water-repellent preservative to the cut end, or wrap the end in a bituminous felt left open at the top.
  3. Ensure a ventilated mechanical bearingRest the end on a rot-proof packer or a ventilated bearing pad placed on the DPC, without any wet grout or mortar bedding.
  4. Provide access for subsequent inspectionAvoid airtight interior lining directly against the bearing timber; design demountable casings that allow inspection of the condition of the member.

Visual access after completion of interior finishing work is an essential technical requirement for durable timber framing. All too often, perimeter thermal insulation and plasterboard completely conceal the wall plate-to-wall connection, preventing the detection of accidental leaks from the verge or thermal bridges that cause internal condensation.

When adjusting purlins on construction sites at height, installing anchorages into the ring beam is carried out in accordance with OTConst art. 22, which requires a perimeter guardrail comprising a top rail at least 100 cm above the working surface, at least one intermediate rail, a toeboard of at least 15 cm, and a maximum spacing of 47 cm between elements. The carpenter works safely along the wall head without risking a fall to the exterior.

Timber-concrete interface: packing, tightening and levelling course isolation

The wall plate is directly subjected to residual moisture from the structural work and potential rising damp. On French-speaking Swiss construction sites, installing a timber sole plate on a reinforced concrete ring beam or brick masonry requires a continuous waterproof barrier. When the raw level shows variations in flatness, packing must not be improvised with construction site offcuts that risk rotting or settling under the load of the rafters.

Watertight DPC strip
Elastomeric bituminous interlayer membrane or rot-proof synthetic strip laid between the ring beam concrete and the underside of the wall plate, projecting by at least 20 mm on both sides to prevent any direct contact between the timber and the mineral structure.

Levelling is carried out before final fixing. Carpenters use polypropylene packers or dense, fully preservative-treated timber shims, placed in line with the mechanical anchorage points. Subsequent dry-packing under the member with non-shrink mortar ensures continuous bearing, preventing point bending of the plate under the heel of each truss or jack rafter.

Types of interlayer and bearing tolerances according to the type of mineral substrate
Masonry substrateInterlayer materialFixing methodFlatness check
Smooth reinforced concrete ring beamEPDM strip or 4 mm reinforced bitumenChemically anchored threaded rods with wide washersMaximum level tolerance: 5 mm under a 2 m straightedge
Rough / patched concreteBituminous strip on a fresh mortar bed or PVC packersExpansion anchor bolts for non-cracked concreteMaximum level tolerance: 8 mm with compensation using non-shrink mortar
Clay brick masonryThick bituminous felt with eaves projectionThrough-bolts anchored into the concrete padstoneMaximum level tolerance: straight line alignment with a chalk line under the plate

For the carpenter, coordination with the bricklayer is essential. Under art. 365 CO, the contractor must report without delay to the client any defect found in the supplied material or in the substrate designated by him as soon as the masonry levelling course displays defects that impair installation.

Purlin ends at the wall head and inspection pockets

The end of a wall plate or ridge purlin embedded in the head of a gable wall represents the area most vulnerable to wood-decay fungi. The end of the timber exposes its end grain fibres, where water absorption by capillary action is up to one hundred times higher than on the longitudinal faces. Encasing this end directly in mortar or against damp masonry leads to concealed internal rot.

  1. Provision of the ventilation pocketForm a masonry pocket leaving a free space of at least 20 mm around the perimeter of the timber member and at least 50 mm at the end, allowing ambient air to circulate.
  2. Shop treatment of the timber endLiberally apply a fungicidal and water-repellent preservative by brushing or dipping on the end-grain cuts prior to erection on the construction site.
  3. Installation of the insulating bearing packerSupport the purlin end on a packer made of durable, non-porous material, such as a galvanised steel bearing plate or a high-density synthetic pad, preventing direct contact with the bottom of the pocket recess.
  4. Provision of inspection accessEnsure the pocket can be inspected from the roof space via a removable access hatch or an airtight yet demountable casing, preventing complete encapsulation by interior insulation linings.

When assembling these heavy elements at the outer edge of the wall, collective safety comes first. In accordance with OTConst, a perimeter guardrail must be installed in unprotected locations where the fall height exceeds 2 m. Carpenters working to adjust the bearing of the wall plate must not dispense with these edge protection systems before the member is securely anchored to the ring beam.

Managing levelling course non-conformities and remediating bearings

On the construction site, defects observed at wall-plate level almost systematically stem from direct contact with damp masonry or from poorly installed anchor bolts in the reinforced concrete ring beam. When the site foreman observes an irregular, unsealed levelling course or one outside elevation tolerances, installation of the wall plate must not begin. Under art. 365 CO, if the material supplied by the client or the site designated by him is found to be defective, or if any other circumstance arises which compromises the proper or timely execution of the work, the contractor must inform the client immediately, under penalty of bearing the consequences. This written notice protects the carpenter against future damage claims related to rising damp.

  • Presence of standing water or absence of a watertight levelling screed: demand the installation of a torched-on elastomeric bituminous membrane or an EPDM waterproofing strip at least 1.2 mm thick under the timber sole plate.
  • Misaligned cast-in threaded rods or missing starter bars: reject cold-bending of the rods; specify new mechanical drillings with approved injection resin into sound concrete, at the statutory distance from the wall edges.
  • Confined purlin end without expansion gap: create a mechanical pocket to ensure a free perimeter air gap of at least 20 mm around the end fibres.
  • Fungal decay on existing work: cut back the bearing timbers to sound wood, prop the roof structure beneath the rafters, and insert a rot-proof isolation packer with certified remedial treatment.

The company's liability extends to verifying the overall stability of the structure. In accordance with CP, any person who, in directing or executing a construction or demolition project, intentionally breaches the recognised rules of the trade and thereby knowingly endangers the life or physical integrity of persons is liable to a custodial sentence not exceeding five years or to a monetary penalty; in the case of negligence, the penalty is a custodial sentence not exceeding three years or a monetary penalty. Anchorages into the ring beam must strictly comply with the specified embedment depths and tightening torques.

Frequently asked questions

How can a levelling course defect be corrected before installing the wall plate?

If the out-of-level exceeds the masonry tolerances, isolated timber packers that create voids under load must be avoided. The bricklayer must cast a reinforced levelling screed or use non-shrink grouting mortar. Between this rectified concrete and the plate, always install a continuous watertight DPC strip projecting by two centimetres on both sides to block any rising damp reaching the wood.

What should be done when an anchor bolt hits a rebar in the ring beam?

It is strictly forbidden to cut the main reinforcement of reinforced concrete without the civil engineer's approval. Shift the fixing point along the axis of the wall plate while observing the prescribed centres. If the timber is already drilled, drill a clean new through-hole in the timber member and inject a chemical anchor with a zinc-plated or stainless steel threaded rod into the newly drilled hole.

What minimum air clearance must be maintained around the end of a purlin?

The end of a wall plate must never touch raw masonry, plaster, or concrete. Provide a ventilated perimeter air gap of at least 20 millimetres at the end and on the lateral flanks of the timber. This gap allows the timber to dry out if it experiences accidental water ingress, thereby preventing confinement and the development of wood-decay fungi on the end grain.

How can access be arranged to inspect the wall plate after interior finishes are completed?

When installing insulation linings and interior wall finishes, provide an inspection access hatch or demountable grilles in line with the main anchors and recessed purlin ends. These pockets allow direct visual inspection of the timber's condition, verification that no residual moisture is present, and possible retightening of the anchor nuts after the building's first complete heating cycle.

Texts and standards cited

  • CO art. 365material and site: the contractor is liable for the good quality of the material he provides; if the material supplied by the client or the site designated by him is found to be defective, or if any other circumstance compromises the proper or timely execution of the work, he must immediately inform the client, under penalty of bearing the consequences (al. 3)
  • CPbreach of the rules of the art of construction: any person who, in directing or executing a construction or demolition project, intentionally breaches the rules of the trade and knowingly endangers the life or physical integrity of persons is liable to a custodial sentence of up to five years or to a monetary penalty; in the case of negligence, up to three years or to a monetary penalty

In the same section