Key takeaways
- Strictly follow the lifting points determined by the manufacturer during CNC cutting and fabrication.
- Always use a lifting spreader beam to eliminate lateral bending stresses.
- Install push-pull props and temporary ties before releasing the hook.
- Rigorous ground demarcation to prohibit any presence beneath moving loads.
Attachment, slinging and managing out-of-plane buckling risks
A traditional timber roof truss in solid timber or glulam possesses optimal structural stiffness in its vertical plane, for which it was calculated. Conversely, its lateral inertia remains extremely low. During the transient lifting phase, tilting up from the storage stack and subsequent aerial transport generate dynamic stresses capable of causing irreversible buckling or out-of-plane distortion of the rafters and tie beam.
- Out-of-plane buckling
- Lateral geometric distortion of a structural element under compressive or torsional forces acting outside its primary plane of inertia.
Direct two-leg slinging from the central crane hook applies oblique compressive forces to the top chord. The wider the sling angle, the more destructive the parasitic horizontal component becomes. Using a rigid spreader beam is essential as soon as the truss span exceeds standard basic dimensions. It ensures suspension legs remain strictly vertical, transferring the lifting load directly to the slinging points provided by the manufacturer without generating lateral pinching.
- Check conformity with the lifting plans provided by the timber engineering office.
- Inspect lifting pins and tighten workshop metallic brackets.
- Fit edge-protection sleeves onto structural timber components.
- Attach taglines to orient the component from a distance without manual handling.
When releasing from the trailer or pre-assembly stack, the initial tilt-up is carried out slowly. If the truss is lying flat, standing it up vertically requires temporarily reinforcing the tie beam with bolted timber side plates if calculations reveal excessive flexibility in the assembly.
Immediate stabilisation at the head and strict control of the slewing zone
Landing the truss on its final bearings, often wall plates on load-bearing walls or timber posts, is the most critical phase. While suspended, its equilibrium depends entirely on the crane hoist rope. Detaching the slings immediately upon contact with bearing shims is an error that causes severe overturn accidents.
- Landing and guidingSlow descent of the truss guided by two carpenters using taglines, without standing beneath the element.
- Bearing fixationInstalling temporary or permanent base-connection fasteners on the wall plates.
- Triangulated proppingInstalling at least two sturdy push-pull props anchored to a stable load-bearing structure, such as a concrete slab or braced posts.
- Spacing tiesFor subsequent trusses, immediate installation of a rigid spacing tie connected to the first already propped truss.
- Unhooking authorisationInstruct the crane operator to slacken slings only after visual confirmation of prop anchoring.
At workstations and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building components or falling objects and materials.
art. 17 OTConst
In accordance with general prevention rules, the ground hazard area within the slewing radius and beneath the path of the truss must be marked with physical barriers and warning signs. No personnel may stand under the load, whether in transit or being seated on truss heel joints.
| Component | Check point | Acceptance criterion |
|---|---|---|
| Push-pull props | Top and bottom anchorages | Bolts tightened, zero play |
| Temporary ties | Head connection | Specified timber section, fully nailed or screwed |
| Wall plate bearings | Alignment and packing | Full bearing contact, mechanical fixings engaged |
| Verticality | Plumb level | Plumb tolerance maintained before tension release |
Lifting kinematics and controlling out-of-plane distortion
A traditional or flitched timber truss possesses considerable major-axis inertia in its vertical plane, but extremely low transverse stiffness prior to installing purlins and permanent bracing. When breaking off the ground or semi-trailer, the slightest oblique pull induces a lateral bending component that initiates out-of-plane buckling. To eliminate these parasitic forces, slinging must strictly follow the attachment points defined by the engineering office or manufacturer on the cutting schedule.
- Lifting spreader beam
- Intermediate metallic beam suspended from the crane hook, distributing the load across multiple parallel vertical legs to eliminate horizontal force components on rafters or tie beams during lifting.
Using a rigid spreader beam is essential as soon as the truss span exceeds ten metres or timber sections feature high slenderness ratios. Unlike direct bridle slinging that compresses the top chords inwards and increases the risk of arching, a spreader beam ensures suspension legs remain perfectly plumb. Manufacturer-designed slinging points generally incorporate through-bolts, flat webbing slings with corner protectors at rafter nodes, or calibrated screw eyes installed on the neutral axis of load-bearing timbers.
| Truss configuration | Preferred lifting method | Predominant mechanical risk | Prevention measure during lifting |
|---|---|---|---|
| Traditional king-post truss with raised tie beam | 2 vertical legs under spreader beam at rafter nodes | Lateral buckling of the tie beam under residual compression | Temporary timber side plates bolted to the bottom chord |
| Stub-tie or collar-tie truss | 4 balanced attachment points under spreader frame | Spreading of knee braces and overturning at the apex | Temporary metallic restraint tie securing truss heel joints |
| Industrial flitched truss or glulam truss | Factory-drilled lifting holes with dedicated lifting pins | Instant out-of-plane buckling due to ridge torsion | Temporary longitudinal stiffener bolted along the top edge |
At workstations and passageways, measures must be taken to ensure that workers are not endangered, under art. 17 OTConst. Throughout the hoisting phase, carpenters guide the structure from a distance using two hemp or polypropylene taglines of at least 20 mm diameter, fastened to the ends of the tie beam. This manual guidance strictly forbids any direct physical contact with the moving load until it has been lowered down to bearing level on the wall plates.
Bearing anchoring, temporary bracing and unhooking protocol
The final landing of the truss on reinforced concrete wall plates or timber posts is the most critical phase on the construction site. Guidance concludes with precise engagement of tenons into mortises or seating onto cast-in metallic brackets. During this period, the crane keeps the truss under light tension: slacking the hoist rope is strictly forbidden until the spatial stabilisation system has taken up all overturning forces.
- Positioning and clamping truss heel jointsEngage heel brackets or birds-mouth joints on the wall plate. Immediately insert pins, coach screws or hold-down bolts without fully clamping thermal expansion play before checking setting-out axes.
- Installing top push-pull propsSecure a minimum of two heavy-duty tubular steel props between the king post or rafter-tie node and the concrete slab below, using metal anchors sized for pull-out loads.
- Lateral triangulation to adjacent bayIf an initial truss or stable gable already exists, diagonally nail two temporary bracing battens of minimum 24 x 100 mm cross-section to complete an undeformable stability triangle.
- Plumb verification and safe unhookingCheck verticality with an optical or spirit level. Instruct the crane operator to slacken slings slowly, observe that no residual out-of-plane deflection occurs, then detach lifting hooks from a safe access platform.
Anchoring temporary props at floor level requires particular attention. On a concrete slab, using suitable concrete screws provides immediate load-bearing capacity without curing time. On timber joisting, the prop base plate must be screwed directly into a main joist using coach screws, never into simple particle board subflooring. Once the truss is disconnected from the crane, immediate installation of the ridge purlin and wall-plate purlins ties the bay together before lifting the next element.
Managing crane lifting anomalies: stop procedure and securing operations
When lifting a timber roof truss, the occurrence of excessive out-of-plane buckling, a sudden gust of wind or improper seating on wall plates requires immediate stoppage of the operation. A timber truss structure exhibits minimal stiffness perpendicular to its fabrication plane. If the component starts to buckle under asymmetric pulling or wind loading, the crane operator must hold the winch without applying abrupt lowering movements that could generate dynamic loads damaging to joints.
- Stopping movement and maintaining rope tensionThe lifting supervisor signals an emergency stop to the crane operator. The load remains suspended, with the hoist rope held under controlled tension to prevent timber buckling failure or shearing of metal connectors.
- Evacuating the slewing zoneAll personnel clear the direct ground hazard footprint. Under art. 17 OTConst, at workstations and passageways, measures must be taken to ensure that workers are not endangered by the collapse of building components or falling objects and materials.
- Correcting geometry from a distanceStabilisation is carried out without stepping beneath the component, using perimeter taglines previously hitched to rafter nodes, or using dedicated guide poles.
- Emergency propping prior to any interventionIf the truss is already seated on its bearings but lists laterally, temporary diagonal timber bracing of minimum 60/120 mm cross-section is anchored from the slab or ring beam before carpenters are permitted to approach.
Any deliberate breach of technical handling rules engages the liability of site management. Art. 229 CP punishes with a custodial sentence of up to five years or a monetary penalty anyone who, in directing or executing a construction project, intentionally infringes the recognised rules of the trade and thereby knowingly endangers the life or physical integrity of persons.
Frequently asked questions
What should be done if the manufacturer-specified slinging points do not align with the site spreader beam?
Improvising direct slinging around structural timber members without engineering approval is prohibited. The lift must be suspended. The sling angle and point locations determine out-of-plane stresses in the connectors. The carpenter contacts the design office at the fabrication shop to recalculate the lifting arrangement or adjusts the drop-leg spacing on the spreader beam using certified shackles and approved master links.
At what wind speed must roof truss crane operations be stopped?
The operational limit is generally between 35 and 45 km/h depending on the exposed surface area of the truss, wind resistance and crane jib length. The Construction Work Ordinance requires operations to cease whenever meteorological conditions compromise safety. The lifting supervisor and crane operator must stop lifting as soon as taglines no longer guarantee full control over the trajectory.
Can the crane be unhooked as soon as the truss heels are fixed to the wall plates?
No. Securing the truss heels prevents horizontal sliding but provides no resistance against overturning or out-of-plane deflection of the structure. The element remains unstable under its own weight and wind forces. Detaching the crane hook is strictly conditional upon installing at least two temporary diagonal push-pull props, securely anchored at the head of the truss and fixed to the slab or supporting walls below.
Who is authorised to enter the restricted ground zone during lifting?
No person is permitted beneath the suspended load or within the slewing perimeter of the truss while it is in motion. The safety perimeter must be marked out on the ground using physical barriers or chains. Only erectors wearing personal protective equipment may approach the permanent bearings once the truss is stabilised at bearing height and the crane trolley has come to a complete stop.
Texts and standards cited
- OTConst art. 17protection against collapsing building components or falling objects and materials: at workstations and passageways, measures must be taken to ensure that workers are not endangered.
- CPbreach of the recognised rules of the building trade: anyone who, in directing or executing a construction or demolition project, intentionally infringes the recognised rules of the trade and thereby knowingly endangers the life or physical integrity of persons is liable to a custodial sentence of up to five years or a monetary penalty; if through negligence, to up to three years or a monetary penalty.
