Skip to content
Website
🧱 CFC 283Finishes: lacquer, oil and waxChapter 4 of 10 in the section

Oiling: saturation, penetration time, wiping off the excess and sticky surface

This chapter details the rules for applying a hard oil to a bare sanded parquet floor. You will learn how to precisely manage the penetration time in the fibres, execute a perfect wipe without leaving excessive thickness, use the single-disc machine for finishing buffing, and technically remedy a floor that has remained tacky.

Key takeaways

  • Hard oil saturates the wood pores but must not form any continuous surface film.
  • Manual or mechanical wiping must imperatively take place before the product begins to gum up.
  • Single-disc machine polishing eliminates oil exudation and standardises the matness of the floor.
  • A sticky surface requires mild chemical stripping or complete sanding depending on the oxidation.

Managing oil penetration and removing excess before gumming occurs

Unlike a varnish that forms a continuous protective film on the surface, parquet oil acts by impregnation deep into the cellular structure of the wood. The mechanical and chemical bond is established in the pores opened by the final sanding grit. Any amount of oil left above the wood surface does not harden under foot traffic: it oxidises upon contact with atmospheric oxygen, thickens, becomes sticky and permanently traps ambient dust. A correctly oiled parquet floor is dry to the touch as soon as the work is completed.

Gumming of the oil
Intermediate oxidation stage during which binders and solvents begin to react with the ambient air. The fluid liquid becomes a viscous paste that is extremely difficult to wipe off without heavy solvent.

The first coat is applied using a flat brush (spalter), a short-pile roller or a notched squeegee, proceeding in regular strips along the grain of the wood. From the moment of spreading, the floor layer monitors absorption. The waiting time before wiping is generally between 15 and 30 minutes, depending on the ambient temperature, the room humidity and the density of the wood species. Oak or ash absorbs quickly through its large vessels, whereas dense or resinous wood slows down impregnation. If the oil dries too quickly due to a draught or excessive heat, the product sets prematurely.

  1. Even distributionDeposit the oil on the dust-free floor and spread it evenly without creating persistent puddles along the edges.
  2. Observation of oil exudationAllow the wood to absorb the product for the period prescribed by the manufacturer until the porous areas become matt and oily beads remain on the dense areas.
  3. Primary wipingRemove all liquid surplus using lint-free cotton cloths or a soft rubber squeegee pulled towards the untreated area.

Mechanising finishing wiping and treating a sticky surface

Manual wiping is not sufficient on medium to large construction sites. The use of a low-speed single-disc machine fitted with a white or beige pad is essential to standardise the finish and force the product down into micro-imperfections. Passing the machine compresses the oil into the grain and removes micro-droplets rejected by reverse capillarity, a phenomenon that occurs frequently when the wood warms up after application.

Choice of machine pad and role during the oiling phase
Tool or consumableMechanical actionIntervention stageDesired result
Beige or red padMedium frictionPenetration finishDrives dense oil into the wood and opens the pores
Standard white padGentle polishingMain wipingAbsorbs surplus without scratching the fibres
Cotton cloth under padMaximum absorptionImmediate final buffingLeaves the wood perfectly dry and matt

When a surface exhibits sticky areas following late or insufficient wiping, the floor layer must adapt their intervention according to the progress of hardening. If the product has been tacky for less than 24 to 48 hours, it is possible to reactivate the resin by applying a very thin coat of fresh oil or a specific solvent recommended by the manufacturer. Fresh oil dissolves the gummed oil in a few minutes. The single-disc machine equipped with a red or green pad immediately breaks up the amalgam, which is promptly wiped clean with clean cotton cloths placed under the disc.

Conversely, if the oil has dried for several days or weeks in excessive thickness, polymerisation prevents any clean redissolution. The film forms elastic crusts that instantly clog abrasives. Remedial work then requires meticulous manual scraping of the accumulation areas or complete sanding of the parquet floor with medium and then fine grit to return to bare wood, before restarting the saturation protocol from scratch. These defects engage the professional liability of the installer and considerably lengthen the duration of unavailability of the premises.

Control of penetration and mechanical neutralisation of the surface film

The fundamental principle of parquet oiling lies in saturating the pores without forming a superficial sacrificial film. The oxidative or waxy hard oil must penetrate intimately into the cellular network of the wood without creating a continuous film above the surface layer. Unlike a varnish which protects via a physical barrier resulting from film-forming drying, oil hardens by polymerisation under the action of atmospheric oxygen in internal contact with the wood fibres. Any amount of product left as excess on the surface layer oxidises in the open air without being able to dry through to the core. This technical error produces a viscous, staining and sticky film, which instantly traps construction site dust and leads to rejection of the work during acceptance in accordance with standard SIA 253.

During this fifteen to twenty-minute impregnation phase, the team leader monitors the absorption heterogeneity of the raw substrate. On indigenous wood species such as oak or ash, springwood areas and cracks absorb the binder abundantly, whereas medullary rays and summerwood saturate very quickly. Excess liquid must be redistributed using a flexible metal spreader or a short-pile mohair roller, moving the material from shimmering areas to areas that have become matt. If dried-out areas appear prematurely, a slight spot-recharge is carried out. As soon as the time limit is reached, the viscosity of the product increases due to the evaporation of solvents, prohibiting any additional delay.

Complete wiping constitutes the decisive phase of execution. As soon as the application time has expired, the excess is pulled with a soft rubber squeegee to gather the surplus, then wiped vigorously with a bleached, lint-free cotton cloth. This manual roughing-out intervention is imperatively followed by mechanical polishing using a rotary single-disc machine rotating at low speed (approximately 150 revolutions per minute). Equipped with a beige or white pad under which a clean absorbent cloth is fixed, the machine equalises the buffing, extracts residual oil lodged in the bevels and tongue-and-groove joints, and neutralises any risk of tackiness. The result is validated under grazing light: the appearance must present a perfectly uniform silky matness, with no shimmering reflection or greasy sensation to the touch.

Treatment of sticky surfaces and neutralisation of oxidation gumming

When a freshly treated parquet floor remains sticky after twenty-four to forty-eight hours, the cause systematically stems from incomplete wiping of the excess or insufficient mechanical polishing. The oil remaining on the surface has begun surface polymerisation, forming a watertight skin that deprives the lower layers of oxygen. This sticky material, consisting of unstable linoxin, will never dry spontaneously, even after waiting several weeks, and irreversibly traps impurities. Depending on the elapsed time and the thickness of the greasy deposit, remediation requires a rigorous protocol to sanitise the work without altering the base sanding.

Diagnosis of surface gumming and remedial protocols according to the state of oxidation
Defect stageMechanical observationCorrective methodRequired equipment
Fresh gumming (< 24 h)Sticky film under the fingernail, adherence of shoe soles, shiny streaksImmediate solvation by adding a thin coat of fresh oil or thinner, mixing and complete wipingSingle-disc machine at 150 rpm, red or green pad, clean cotton cloths
Intermediate gumming (24 h to 7 days)Gelified surface, soiling upon traffic, viscous peeling when scrapedSurface stripping with emulsifying intensive cleaner, abrasive brushing, rinsing with a wrung-out sponge then dryingSingle-disc machine, brown or black pad, wet vacuum cleaner, absorbent cloths
Hardened reticulation (> 7 days)Irregular crust hardened on the surface but soft underneath, rough orange-peel textureMechanical dry sanding to shear the surface film without cutting into the wood, dusting and equalising oilingSingle-disc machine with 120 to 150 grit abrasive screen, white pad for finishing

In the case of recent gumming, chemical reactivation remains the most rational and least invasive intervention. The controlled application of a tiny fraction of fresh oil or a suitable de-aromatised solvent dissolves the viscous resin by direct molecular affinity. The single-disc machine rotates the intermediate pad to break the nascent varnish, then dry cloths placed under a white pad mop up the entirety of the liquefied mixture. The wiping cloths must be replaced regularly during the work to avoid redepositing the greasy emulsion onto adjacent bays.

Protocols for repairing an oxidised oil film and emergency procedures on site

When complete wiping of the excess has not been carried out within the twenty to thirty-minute window, the drying hard oil begins its polymerisation upon contact with ambient air. Instead of deeply nourishing the cellular network of the wood, the product sets into a sticky, heterogeneous and patchily shiny surface film. This surface layer traps construction site dust, refuses to dry to the core and marks at the slightest footstep. Letting it ventilate while hoping for spontaneous hardening constitutes a major technical error: the film remains sticky for several weeks and compromises the acceptance of the work according to the appearance criteria of standard SIA 253.

  1. Immediate chemical neutralisation (observed within 24 to 48 hours)As soon as sticky areas appear the day after application, soften the film by re-applying a thin coat of the same hard oil or a de-aromatised solvent recommended by the manufacturer. Fresh solvents soften the resin undergoing oxidation. Work immediately with a single-disc machine equipped with a green or burgundy pad to shear the residual gumming, then wipe all greasy residue with pure cotton cloth until total dryness of the substrate.
  2. Mechanical abrasive sanding (observed after 72 hours)If the surface film has polymerised irreversibly into a rubbery mass, solvent stripping becomes ineffective. The surface must be mechanically sanded using a single-disc machine or an orbital sander fitted with a fine 120 to 150 grit abrasive disc or a silicon carbide mesh pad. The clogged abrasive must be replaced as soon as it is saturated to avoid burning the wood or creating scorch marks on the fibres.
  3. Mechanical equalising polishing and re-impregnationAfter thorough dust removal with an industrial vacuum cleaner, carry out mechanical polishing using a dry white pad to check the neutrality of the substrate. Apply a very thin maintenance coat, allow to penetrate for a maximum of ten minutes, then carry out a full wipe with a cloth under the drive plate. The final surface must present an immediate dry touch and a perfectly silky matt appearance.

Frequently asked questions

How to immediately identify whether the penetration time of a hard oil has been exceeded?

The impregnation period ranges between fifteen and twenty-five minutes depending on the ambient humidity. If the oil changes viscosity, becomes syrupy under the finger or excessively hinders the squeegee, the product is beginning its surface polymerisation. As soon as the cloth fluffs or catches instead of gliding freely, the limit has been crossed. The area must be immediately saturated with fresh oil to fluidify the film before extracting all the excess.

Why does an oiled parquet floor remain tacky in the hollows of bevels?

When passing the single-disc machine equipped with a wiping pad, the flat foam does not penetrate into the micro-bevels of bevelled boards. Oil accumulates there by capillarity and forms un-wiped liquid beads that take weeks to harden. The floor layer must imperatively rework each groove by hand using a clean cotton cloth or a flexible spatula wrapped in fabric to dry out each hollow.

Which type of pad should be favoured for mechanical polishing after wiping?

After removing the liquid surplus with a squeegee and then a cotton cloth, final polishing is carried out with a slow single-disc machine using a non-abrasive white pad. For open-pore parquet floors such as oak, adding a cloth under the disc makes it possible to absorb microscopic resurgences emerging from the vascular channels under mechanical pressure. The beige pad can be used on dense woods to satin-finish the fibre.

Can a sticky surface be rectified by applying a varnish or topcoat?

This intervention is strictly prohibited. Applying a polyurethane or aqueous-phase acrylic topcoat over an unpolymerised oily substrate leads to complete detachment due to the absence of chemical and mechanical adhesion. The varnish will blister, peel or whiten under the effect of the residual solvents of the oil. The only acceptable solution consists in chemically degreasing the surface or sanding it down to bare wood before any modification of the finishing system.

Texts and standards cited

  • norme SIA 253Wooden floor coverings and resilient coverings: flatness requirements, appearance tolerances and acceptance checks for surface finishes.
  • Ordonnance sur la prévention des accidentsGeneral obligation of the employer to take the preventive measures required by experience and occupational safety engineering.
  • Ordonnance sur les déchetsPrescriptions applicable to sorting, collection and safe disposal of polluted waste and construction site residues.

In the same section