Skip to content
Website
🧱 CFC 283Glued, floating or nailed installationChapter 2 of 10 in the section

Adhesive: elasticity, consumption, trowel and solid wood requiring greater flexibility

This chapter guides you through the rigorous selection of parquet adhesive and its deformation kinematics. You will learn to adapt the modulus of elasticity according to the width and structure of the boards, to calibrate the trowel teeth to ensure transfer, and to master the open time on your construction sites.

Key takeaways

  • Standard SIA 253 governs the permissible stresses transmitted by the bonding to the mineral substrate.
  • A wide solid board requires an elastic adhesive to absorb shrinkage without tearing the screed.
  • The trowel teeth dictate the consumption per square metre and the transfer rate.
  • Exceeding the open time forms a surface skin that destroys the mechanical adhesion beneath the boards.

Adapting the adhesive's elasticity to the dimensional constraints of the boards

Solid wood reacts continuously to indoor climate variations through tangential and radial dimensional changes. The wider a solid board is, the greater the absolute amplitude of its shrinkage or swelling. By applying a rigid adhesive under a solid oak strip wider than 120 millimetres, the shear stresses generated by hygroscopic movement are transferred entirely to the adhesive layer and the upper surface of the screed. If the surface cohesion of the mortar is less than the applied stress, the screed tears away through horizontal delamination. Conversely, if the substrate resists, the board experiences internal tensions that cause longitudinal splits in the heartwood.

Standard SIA 253 specifies that the bonded installation system must guarantee the stability of the work without altering the supporting substrate. To neutralise these shear forces, the parquet installer uses silane-terminated polymer-based adhesives or single-component polyurethanes classified as elastic to hard-elastic. An elastic adhesive allows slight transverse sliding under the board during seasonal variations, damping the peak tension transmitted to the cement or calcium sulphate screed. For multi-layer parquet, whose cross-laminated structure mechanically stabilises the wear layer, a hard-elastic adhesive remains preferred in order to limit wave deformations while firmly maintaining the assembly.

Mechanical behaviour of adhesives according to parquet board typology
Parquet typeBoard widthRecommended adhesive familyMechanical behaviour
Mosaic or on-edge lamellaeUp to 50 mmDispersion or hard-elastic silaneRigid to semi-rigid, locking small elements
2- or 3-ply multi-layerUp to 190 mmHard-elastic modified silane (SMP)Moderate absorption, excellent shear resistance
Traditional solid woodUp to 120 mmPolyurethane or hard-elastic silaneBalance between axial retention and joint flexibility
Wide solid woodGreater than 130 mmModified silane or elastic polyurethaneContinuous elastic deformation without film rupture

Calibrating the trowel, controlling consumption and respecting open time

The efficiency of a bond depends on the geometry of the adhesive beads crushed during installation. The choice of notched trowel directly determines the amount of adhesive deposited per square metre as well as the effective contact surface between the back of the parquet element and the screed. According to the execution guidelines of standard SIA 253, the adhesive transfer rate under the parquet board must reach at least 80% in general areas, and tend towards 100% on thick solid parquet or installations on heated screeds. An unsuitable tooth size leads to air pockets under the parquet, causing hollow walking noises and areas of lower mechanical resistance.

  • TKB B3 tooth profile: consumption of 800 to 1000 g/m², reserved for thin tongue-and-groove boards or small formats on a perfectly flat substrate.
  • TKB B11 tooth profile: consumption of 1000 to 1250 g/m², standard trowel for multi-layer parquet up to 200 mm wide and solid wood of standard thickness.
  • TKB B15 tooth profile: consumption of 1200 to 1500 g/m², wide triangular profile essential for thick solid flooring or rough-sawn undersides.
  • Regular replacement of trowel blades: steel wear reduces notch depth by 1 to 2 mm after a few dozen square metres, leading to an unnoticeable adhesive deficit.
Skinning time and open time
The skinning time is the waiting interval allowing partial solvent evaporation or the initiation of polymerisation. The open time represents the useful window during which the adhesive bed wets the reverse side of the wood perfectly without forming an insulating dry film.
  1. Control of thermo-hygrometric conditionsVerify that the ambient air shows between 40% and 65% relative humidity and a temperature between 18 and 22 °C to avoid the abrupt acceleration of the setting time of silane polymers.
  2. Adhesive application in fractionated areasSpread the adhesive using the trowel tilted at 45° over an area not exceeding the installation capacity of the crew for the next twenty minutes, without exceeding the open time guaranteed by the technical data sheet.
  3. Installation and mechanical clampingLay the board using an oblique sliding movement to flatten the ridges of adhesive, engage the tongue and groove, and tap with a heavy beating block to ensure immediate adhesion.
  4. Destructive verification probingLift a freshly laid board during start-up to validate the absence of a surface skin and visually check the uniform crushing of the grooves across the entire balancing layer.

Solid wood mechanics and shear stresses according to standard SIA 253

The bonded installation of wide solid oak or native hardwood boards subjects the screed-adhesive-wood interface to considerable physical stresses. Wood is a hygroscopic and anisotropic material whose tangential shrinkage reaches twice its radial shrinkage. During seasonal cycles in Switzerland, a 160 mm solid board tends to vary by one to three millimetres. If the chosen adhesive exhibits purely rigid behaviour, all this driving force is immediately converted into pure shear at the surface of the mineral substrate. According to standard SIA 253, the bonding system must reconcile the surface mechanical resistance of the screed and the shrinkage force specific to the wood species.

Analysis of failures shows two modes of failure induced by an overly rigid adhesive. With a traditional product based on hard epoxy or two-component polyurethane, the adhesive film refuses any elastic creep. If the cement or calcium sulphate screed lacks surface cohesion, the tension tears off the upper layer of the mortar: the parquet lifts, taking a friable mineral crust with it. If the substrate resists perfectly, the energy remains trapped within the cellular structure of the wood: the board splits along the grain or undergoes permanent cupping that breaks the assembly edges. Elastic and hard-elastic polymer adhesives instead act as a damping interface: they absorb a decisive share of the shear stresses without exceeding the breaking limit of the screed or splitting the boards.

Mechanical behaviour of adhesives and dimensional compatibility according to standard SIA 253
Adhesive familyModulus of elasticityMax. solid wood widthBehaviour under tension
Elastic modified silaneLow (flexible)120 mmAbsorbs shear; protects the mineral substrate but allows slight joint opening during dry periods.
Hard-elastic polymer hybridMedium (restrained)180 mmOptimal compromise; limits cupping while damping peak tension on the screed.
Hard two-component polyurethaneHigh (rigid)Less than 90 mm or engineeredComplete dimensional locking; full transfer of stresses to the mineral substrate without damping.

Trowel teeth, consumption and transfer control

The polymer's own elasticity only protects the structure if the final thickness of the adhesive bed is sufficient. An adhesive film crushed to less than 0.5 mm under a solid board loses its useful elastic elongation and buffering power. The geometry of the notched trowel, defined by TKB profiling standards, determines the height of the grooves and the consumption per square metre. For wide solid parquets and large engineered boards, installers use a TKB B11 or TKB B15 tooth profile, ensuring a deposition of 1000 to 1400 g/m². This quantity compensates for permissible flatness defects of the substrate and guarantees, after crushing the beads during board beating, a continuous joint of at least 1 to 1.5 mm in thickness.

Mastering the open time and controlling wetting condition the durability of the work according to standard SIA 253. The standard requires an effective adhesive transfer of at least 80% on the underside of each installed parquet board. This rate guarantees a homogeneous distribution of stresses and eliminates hollow areas that generate sound resonance or parasitic movements. The installation team must adapt the glued surface to its actual progress rate, without spreading adhesive over an area exceeding fifteen to twenty minutes of actual work, especially during complex cutting phases.

  • Regularly check the wear of the notched trowel and replace it as soon as the height of the notches decreases by 1 mm.
  • Check effective transfer by lifting a freshly laid board every ten rows to inspect the back of the wood.
  • Energetically beat down each board using an installer's beating block to crush the grooves and expel residual air.
  • Monitor the room's humidity and temperature in order to anticipate the shortening of the open time in hot or dry weather.

Management of bonding defects: delamination diagnosis and corrective measures

When the dimensional behaviour of a wide solid parquet exceeds the deformation capacity of the adhesive, the defect manifests itself rapidly as soon as the first seasonal hygroscopic variations occur. If the selected adhesive exhibits excessive rigidity in the face of wood shrinkage, the shear stresses exceed the permissible mechanical resistance of the assembly. Failure then occurs via two distinct mechanisms: either the board splits within its mass under the effect of internal restraint, or the stress tears away the top millimetre of the mineral screed. The parquet sounds hollow underfoot and marked height differences appear between the edges.

  • Continuous axial cracking of solid wood along the grain, characteristic of shrinkage prevented by a rigid adhesive.
  • Detachment under the adhesive line with transfer of smoothing mortar or screed laitance to the back of the board.
  • Internal cohesion failure of the adhesive bead due to lack of transfer linked to exceeding the open time.
  • Irreversible cupping of wide solid boards due to discontinuous binder distribution or worn trowel teeth.

The joint inspection record is based on the destructive removal of at least two representative elements, according to the evaluation principles of standard SIA 253. Visual inspection of the underside and substrate makes it possible to precisely locate the failure plane. If the adhesive bed remains perfectly adherent to the back of the board but carries away the surface film of the mortar, the defect stems from deficient substrate preparation or an overly stiff adhesive that has not absorbed the transverse stresses.

In the presence of widespread defects on a heavy-section solid parquet, complete removal of the unstable area remains the only sustainable solution. Adhesive residues and unstructured screed layers must be mechanically removed by planing or diamond sanding. Reinstallation strictly requires readjusting the peripheral expansion gaps, applying a high-elasticity polymer adhesive to absorb the residual movement of the wood, and a fresh combing ensuring at least eighty percent actual transfer.

Frequently asked questions

How to determine on-site whether detachment comes from the adhesive or the substrate?

Remove a non-adherent board to inspect the failure plane. If the adhesive adheres to the wood and shows a torn mineral crust, the screed lacked surface cohesion or the adhesive was too rigid. If the adhesive remains on the floor with no residue under the board, the open time was exceeded or the underside was dusty. An adhesive broken in two indicates an under-dimensioning of its elasticity according to standard SIA 253.

Can a solid oak board that sounds hollow be spot-consolidated without removing everything?

This intervention is only conceivable if the defect is very localized and the board does not present pronounced height differences. The injection of a suitable very fluid silane polymer, injected through discreet two-millimetre drill holes plugged with hard wax, makes it possible to fill a localized void. It is out of the question to employ rigid resins that would create undeformable anchor points under solid wood subject to seasonal dimensional movements.

Why does the width of a solid board require the use of a specific elastic adhesive?

Solid wood swells and shrinks in proportion to its total width. On a board exceeding one hundred and twenty millimetres, the millimetric amplitude of seasonal movements generates considerable shear forces at the edges. A modified silane-based elastic adhesive has sufficient elongation at break to accompany these variations without transferring the entire delamination load to the screed's anchorage surface.

What to do if the adhesive has started to form a skin during application?

As soon as a dry film forms on the surface, adhesive transfer to the parquet backing becomes nil. The altered beads must be immediately scraped off with a flat spatula down to the bare mineral substrate before polymerisation, then a fresh pass reapplied with the calibrated notched trowel. Laying a board on adhesive that has exceeded its open time leads to inevitable detachment within a few weeks.

Texts and standards cited

  • norme SIA 253Carpets, linoleum, plastic and elastic coverings, cork, parquet

In the same section