Skip to content
Website
🧱 CFC 283Substrate, preparation and underlaysChapter 9 of 10 in the section

On a staircase: step by step, add-on nosing, slip resistance and nosing wear

This chapter details the cladding of a staircase by the parquet layer, from geometrical measuring step by step to slip-resistant treatment. You will learn how to adjust elements on concrete or wood, how to bond a solid add-on nosing resistant to shear stresses, and how to integrate slip safety devices.

Key takeaways

  • Systematic step-by-step measuring compensates for the dimensional deviations of the raw substrate.
  • The SIA 253 standard governs flatness tolerances and full-surface bonding adhesion.
  • The hardwood add-on nosing absorbs mechanical wear and protects the edge of the tread.
  • The mineral insert or slip-resistant machining guarantees operational safety without degrading the finish.

Measure each step and shim the flight of stairs before adhesive bonding

Cladding a concrete or wood-based panel staircase with bonded parquet tolerates no geometrical approximation. Unlike standard surfaces where slight deviations blend out over long lengths, a stringer or notched stringer immediately reveals the slightest out-of-squareness. The SIA 253 standard requires rigorous substrate verification: dryness of the work, surface cohesion and compliance with flatness tolerances. On a raw stringer, riser heights and tread depths frequently vary by several millimeters from one level to the next.

  1. Checking step heightsCheck the height of each raw step by incorporating the final thickness of the parquet and adhesive system. The initial starting step and the final landing step represent the critical points where the finished levels must align rigorously with adjacent floor coverings.
  2. Individual template takingMeasure each step independently using a stair gauge or an articulated-arm contour gauge. The tool records re-entrant angles, the out-of-plumb of the side cheeks and any curves of winders.
  3. Transfer and cutting for adjustmentTransfer the geometrical marks onto the parquet plank or layout sheet in the workshop. Allow for a millimeter-scale peripheral gap along the masonry stringers, which will be sealed with a flexible joint or masked by a grooved skirting board.
Preliminary substrate checks before bonding according to SIA 253 standard
Checked elementAcceptance criterionConsequence of a defect
Residual moisture of concreteSuitable moisture content without moisture returnAdhesive detachment and wood cupping
Surface cohesionSound, dust-free substrate, free from laitanceFailure of the bonding interface under the step
Step regularityStrict flatness under the 1 m straightedgePlank deflection and squeaking noises
Height differenceConstant tolerance across the entire flightTripping hazard for the user

Shape the add-on nosing and treat slip resistance

The stair nosing undergoes the highest mechanical stress of the entire floor: it absorbs the direct impact of the heel on the descent and the horizontal shear of the forefoot on the ascent. To guarantee the durability of the work, the edge cannot rest on a simple multi-layer parquet wear layer exposed at the end. The parquet layer installs a solid wood add-on nosing of the same species or a prefabricated tongue-and-groove reinforced assembly piece. The solid profile protects the tread against chipping and conceals the riser.

  1. Machining and profile assemblyShape the oak or hardwood add-on nosing with a slightly softened or rounded edge of a defined radius. Assemble the piece to the flat of the step using a loose tongue, locked groove or scarf joint to maximize the adhesion surface.
  2. Full-surface structural bondingApply a high shear-strength silane or polyurethane adhesive using a suitable notched trowel. Avoid any adhesive voids under the overhang of the stair nosing to prevent cracking under point loads.
  3. Mechanical holding under pressSecure the nosing and tread plank using angle clamps, clamping blocks or high-adhesion tape without residual tension for the full setting time prescribed by the manufacturer.
  4. Integration of the slip-resistant deviceMachine one or two longitudinal grooves set back from the nosing to insert an elastomer profile, a rough mineral resin or a carborundum tape certified against slipping.

The treatment of the slipperiness of the stair nosing is inseparable from the choice of varnish or finishing oil. A vitrifying film that is too smooth considerably amplifies the risk of slipping on the front edge. The application of a structured surface varnish, complemented by a visually contrasting textured insert, meets accident prevention requirements while ensuring uniform wood wear.

Structural bonding and clamping of the add-on nosing to the step

The stair nosing is subjected to repeated dynamic loads combining horizontal shear when stopping the foot and vertical bending under the user's weight. Laying parquet on a staircase without uncoupling the nosing from the rest of the tread exposes the work to rapid failure of the standard joint assembly. The edge piece must be shaped as an autonomous solid element or assembled in the workshop by jointing, tongue-and-groove reinforcement or a hardwood loose tongue, prior to full bonding onto the concrete or existing wood substrate.

To guarantee long-term stability in accordance with the rules of the parquet trade and the requirements of the SIA 253 standard, the add-on stair nosing cannot depend on simple facing fixation. Direct adhesion to the mineral substrate or old step requires meticulous preparation, free from sanding dust, laitance or varnish residues, combined with a zero-shrinkage reactive adhesive that compensates for micro-tensions.

  1. Dry fitting of the nosing element and treadPresent the cut-to-size step based on the measuring template. Check the plumb of the front edge and the exact overhang of the nosing relative to the face of the riser, reserving the mandatory peripheral gap against stringers or plaster cheeks.
  2. Gluing with a notched trowelApply the silane-terminated polymer or two-component polyurethane adhesive to the flat of the step using a suitable notched trowel. Ensure that the front edge receives a continuous bead without excessive squeeze-out onto the riser.
  3. Pressing and temporary mechanical clampingFirmly compress the assembly using pump clamps bearing against the underside of the structural slab or by wedging light diagonal props against the upper soffit. The use of high-strength masking tape stabilizes the edge during curing.
  4. Connection with the riserEngage the riser under the grooved nosing or against its rear face depending on the adopted cut. Maintain constant pressure to eliminate any air voids likely to generate squeaks upon impact.
Choice of bonding systems for add-on stair nosings according to substrate
Substrate typeRecommended adhesive typeIndicative consumptionRecommended clamping method
Dust-free raw concreteTwo-component polyurethane adhesive1000 to 1200 g/m²Stair clamps or prop shimming
Resurfaced cement screedHigh-modulus MS hybrid polymer adhesive900 to 1100 g/m²Lead weights distributed on the edge
Planed old wood stepSingle-component D4 polyurethane adhesive800 to 1000 g/m²Masked inclined screwing and clamps
Previously degreased metal substrateSolvent-free epoxy-urethane adhesive1100 to 1300 g/m²Edge clamping using mechanical pliers

Wear profiles, slip-resistant treatment and control according to SIA 253 standard

The edge of a staircase is the surface subjected to the highest mechanical abrasion in the entire building. Standard varnish or finishing oil applied to a soft-wood stair nosing degrades within weeks under repeated foot traffic. To ensure satisfactory durability and limit the risk of falls, the parquet layer must integrate specific wear systems and a continuous slip-resistant treatment along the entire useful length of the step.

The SIA 253 standard specifies the functional requirements relating to bonded floor coverings, particularly on stair points where user safety depends directly on slip resistance. The parquet layer's intervention consists of inserting slip-resistant elements that do not create a dangerous step transition but guarantee measurable roughness, even when footwear brings in external moisture.

  • Direct grooving in the mass of the hardwood: machining of two to three parallel grooves 3 millimeters wide and 2 millimeters deep, located between 10 and 40 millimeters from the front edge.
  • Incrustation of metal profiles in aluminum or brass with a carborundum insert: flush recessed installation in the sanded surface to prevent shoe snagging.
  • Pouring an elastomer or polyurethane resin filled with quartz grains: carried out after parquet finishing using an adhesive masking template to obtain a clean and uniform strip.
  • Installation of bevelled-edge protection angles: solution suited to intensive traffic areas where the end-grain wood of the nosing must be totally encapsulated against impacts from suitcases or light equipment.

During acceptance according to the SIA 253 standard, the parquet layer ensures that the visual contrast of the stair nosing is sufficient for visually impaired persons if tender specifications prescribe it, and that the transition between the abrasive strip and the wood plank exhibits rigorous flatness. The absence of a hollow sound under the nosing attests to effective adhesive transfer over 100% of the underside.

Management of defects: remediation of faulty nosings and slip-resistance defects

On a wooden staircase, dynamic loads at the nosing concentrate most of the mechanical shear stresses. A failure of the adhesive joint between the add-on nosing and the tread plank generally reveals insufficient clamping during curing, an unsuitable adhesive, or an original substrate exhibiting localized deformation. As soon as a clicking sound or loosening appears under heel traffic, the parquet layer must log the defect and check whether the issue stems from bonding weakness or structural movement. If the nosing moves, edge wear accelerates and the risk of toppling increases sharply for the user.

  1. Purging and cutting out the damaged nosingSaw the add-on nosing using a rail-guided plunge saw set back from the edge, then plane down the degraded wood to the load-bearing face of the riser.
  2. Reconstruction of the connectionRoute a groove into the sound edge of the in-place step to insert a solid wood loose tongue or a new calibrated interlocking profile.
  3. Structural bonding and pressingBond the new piece with a reactive polyurethane resin, maintain continuous clamping using suitable clamps and re-establish the slip-resistant device according to the SIA 253 standard.

When the issue concerns excessive slipperiness, insufficient friction coefficient requires immediate finish remediation. If the vitrifying agent proves too smooth or if add-on inserts detach under footwear, the parquet layer locally sands the facing, re-integrates recessed abrasive strips or applies a varnish filled with silica micro-beads. In the event of a dispute with the site management, the Code of Obligations governs the notification of defects and intervention deadlines for repair. Execution tolerances and slip values defined by the SIA 253 standard constitute the technical reference to certify the compliance of the work.

Frequently asked questions

How to intervene when an add-on nosing starts to squeak or exhibits slight play?

A squeak at the nosing reveals a flatness defect under the step or an adhesive that has broken its adhesion film. First check whether the movement originates from the substrate or the wood-on-wood bonding. If the nosing is screwed from underneath, re-tightening after shimming compensates for settlement. In the case of a bonded assembly without bottom access, the nosing must be removed by rip-cutting and a clean connection re-machined.

Can self-adhesive slip-resistant strips be installed on oiled stair parquet?

Wood oils leave a waxy or greasy surface residue that prevents standard adhesives from setting. To install a reliable slip-resistant strip, locally degrease the wood with a suitable solvent, then sand the groove down to raw wood. The ideal approach remains machining a two-millimeter-deep groove to mechanically recess a slip-resistant profile or pour a sanded epoxy resin that will not tear off under traffic.

What to do if the first or last step has a non-compliant height?

The cumulative thickness of the screed, adhesive and parquet modifies the final step height. If prior measuring was neglected, the first step may become too high and the last too low. The parquet layer must then shim the entire flight with compensation panels on the underside of the steps, or adjust the add-on nosings to restore a regular stepping pace and comply with SIA 253 standard tolerances.

How to treat excessive slipperiness on a varnished staircase already put into service?

Without dismantling the work, two technical solutions exist. The first consists of lightly de-nibbing the stair nosing area and applying a two-component polyurethane varnish filled with slip-resistant mineral particles. The second consists of routing one or two parallel grooves three centimeters from the edge to glue in soft elastomer profiles. This latter option offers significantly superior mechanical durability against repeated foot friction.

Texts and standards cited

  • SIA 253Installation of wooden floor coverings and resilient floor coverings, flatness requirements and walking safety
  • Code des obligationsGeneral rules relating to the works contract, the notice of defects and liability for defects in the work

In the same section