Skip to content
Website
🧱 CFC 283Section 4 of 610 chapters

Parquet sanding: grit sizes and flatness: the execution standard

Intended for team leaders, foremen and CFC 283 flooring installers, this guide compiles wood parquet sanding practices according to standard SIA 253. From diagonal initial cutting to finishing surface smoothing, it details abrasive sizing, edge management, leveling of unevenness defects and dust removal to guarantee an impeccable substrate before applying oils, waxes or sealers.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

norme SIA 253

2 mm

Minimum thickness of remaining wear layer before sanding on engineered parquet

norme SIA 253

4 mm

Minimum embedding depth of metal nails before coarse grit attack

norme SIA 253

15° to 30°

Diagonal attack pass angle relative to the wood grain to level the boards

norme SIA 253

0.8 mm

Maximum abrasion thickness commonly removed over a complete renovation cycle

norme SIA 253

2 mm

Flatness tolerance under the 2 m straightedge for a sanded parquet intended for sealing

Technical scope of parquet sanding in Western Switzerland

Sanding a wood installation is at the heart of enhancing solid and engineered parquet flooring. This section covers the mechanical action on the wood wear layer: leveling of height differences, opening of pores, regularization of general flatness and microscopic surface preparation prior to the application of finishes. It addresses the kinematics of continuous belt machines, the edge constraints of rotary edgers, fine particle extraction and coexistence on inhabited renovation construction sites.

This guide does not detail factory board manufacturing or the heating-up protocol for active slabs, which is handled by the heating engineer. Likewise, initial glued or nailed installation is considered here only from the perspective of its final geometry: protruding nails that threaten the drums, seasonal dimensional variations, and substrate flatness defects that require correcting the sander's initial attack.

  • Included: sequential abrasion, stripping of old varnishes, leveling of height differences, edges, corners, binder filling, suction and lighting control of flatness.
  • Excluded: sanding or shot-blasting of mineral substrates (CFC 281), adjustment of skirting boards and door thresholds (CFC 273), fiber-reinforced leveling compound under parquet and adjacent paints (CFC 272).

Swiss quality requirements demand optical regularity without inversion waves or cross-scratches visible against the light. The flooring craftsman commits his guarantee on the durability of the protective film or impregnation, which depends directly on the final grit selected during the last sanding pass.

Reading protocol and operational logic of the chapters

Executing flawless sanding requires compliance with a logical chain of interventions. Each chapter addresses a specific physical constraint, from the initial evaluation of the wear layer to final dust removal under grazing lighting. A poor decision made at the outset compromises the work with no possibility of surface rectification.

Organization of work steps on the construction site
StepAssociated chaptersPriority technical objective
Preliminary diagnosisU4-04 and U4-07Measure the remaining wear layer, punch down nails and identify unstable boards.
Rough sandingU4-01, U4-02 and U4-10Level the floor diagonally, remove old varnish and adjust the pressure.
Edges and junctionsU4-03 and U4-05Level borders with the rotary machine and fill gaps with binder.
Finishes and handoverU4-06, U4-08 and U4-09Extract dust in a clean environment, inspect with a grazing lamp and validate the appearance.

First, study the available wear thickness (U4-04) and the state of mechanical fixings (U4-07). On an old parquet floor, an unpunched nail instantly tears a new abrasive belt and irreparably marks the rubber of the sanding roller. This diagnosis dictates the aggressiveness of the first pass.

The second phase combines the dynamics of the large machine: the grit sequence without any skipped grades (U4-01), the diagonal passing direction to level cupping (U4-02), and the continuous feed speed essential to prohibit stopping depressions (U4-10). The combined mastery of the main machine and the edger (U4-03) conditions visual homogeneity near skirting boards.

Final preparation covers generalized joint filling (U4-05), fine dust collection in accordance with art. 33 OTConst to preserve the working atmosphere (U4-06), and coexistence in an inhabited environment (U4-08). Final visual and tactile inspection (U4-09) closes the cycle before applying protective coats.

📘 Chapters in this section 10

Parquet sanding: grits and flatness

The sequence: starting grit, intermediate grits, finishing grit, no skipping

Master the strict sequence of abrasives to remove scratches without clogging belts prematurely.

Parquet sanding: grits and flatness

The direction: diagonal attack, finishing along the grain, and the hollow left by the machine

Level cupped boards diagonally before aligning the final pass with the grain.

Parquet sanding: grits and flatness

Edges: edge sander, transition with the main machine, corners and half-moon marks

Connect the periphery to the center without creating visible circular marks along the skirting boards.

Parquet sanding: grits and flatness

How many sandings: wear layer, solid wood, engineered wood and parquet already sanded

Measure the remaining wear layer to determine the technical feasibility of a complete renovation.

Parquet sanding: grits and flatness

Filling: wood-dust paste, joints that are too wide and mastic extrusion

Formulate a homogeneous paste to seal gaps without material rejection upon drying.

Parquet sanding: grits and flatness

Dust: integrated extraction, bag, overpressure in the room and cleaning

Contain wood microparticles to respect ambient air and guarantee a clean construction site.

Parquet sanding: grits and flatness

Old parquet: nails to punch in, split boards, and paper torn by a head

Secure nails and stabilize boards to prevent sudden tearing of abrasive belts.

Parquet sanding: grits and flatness

In inhabited environments: noise, dust, room by room and uninhabitable dwelling for two days

Organize room rotation and nuisance management in occupied premises without disputes.

Parquet sanding: grits and flatness

Check before sealing: grazing light, bare hand, and the scratch you will no longer see

Detect micro-scratches and waves under grazing light before applying the varnish.

Parquet sanding: grits and flatness

The machine: belt pressure, feed speed, and the wave it leaves if you stop

Adjust cylinder pressure and coordinate movement to prevent any localized hollowing.